Skip to content

R
raspberrypi-kernel

openeuler / raspberrypi-kernel

通知 13
Star 1
Fork 0
R
raspberrypi-kernel
切换分支/标签
  1. 06 10月, 2009 1 次提交
  3. 21 9月, 2009 1 次提交
  5. 18 9月, 2009 6 次提交
    • J
      libata: Add pata_atp867x driver for Artop/Acard ATP867X controllers · d15d6e6c
      由 John(Jung-Ik) Lee 提交于 
      This is a new pata driver for ARTOP 867X 64bit 4-channel UDMA133 ATA ctrls.
Based on the Atp867 data sheet rev 1.2, Acard, and in part on early ide codes
from Eric Uhrhane <ericu@google.com>.
Signed-off-by: NJohn(Jung-Ik) Lee <jilee@google.com>
Reviewed-by: NGrant Grundler <grundler@google.com>
Reviewed-by: NGwendal Gringo <gwendal@google.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>
      d15d6e6c
    • R
      pata_amd: do not filter out valid modes in nv_mode_filter · 90950a25
      由 Robert Hancock 提交于 
      On a Compaq Presario V3000 laptop (NVIDIA MCP51 chipset), pata_amd selects
PIO0 mode for the PATA DVD-RAM drive instead of MWDMA2 which it supports:

ata4.00: ATAPI: HL-DT-ST DVDRAM GSA-4084N, KQ09, max MWDMA2
ata4: nv_mode_filter: 0x39f&0x7001->0x1, BIOS=0x0 (0x0) ACPI=0x7001 (60:600:0x11)
ata4.00: configured for PIO0

For some reason, the BIOS-set UDMA configuration returns 0 and the ACPI _GTM
reports that UDMA2 and PIO0 are enabled. This causes nv_mode_filter to end up
allowing only PIO0 and UDMA0-2. Since the drive doesn't support UDMA we end up
using PIO0.

Since the controllers should always support PIO4, MWDMA2 and UDMA2 regardless
of what cable type is used, let's make sure we don't filter out these modes
regardless of what wacky settings the BIOS is using.
Signed-off-by: NRobert Hancock <hancockrwd@gmail.com>
Cc: stable@kernel.org
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>
      90950a25
    • M
      sata_promise: update reset code · ff7cddf5
      由 Mikael Pettersson 提交于 
      sata_promise's reset code has deviated quite a bit from
the Promise reference driver's, and it has been observed
to fail to recover from errors in some cases.

This patch thus updates the reset code to more closely
match the reference driver:

- soft reset (pdc_reset_port):
  * wait for ATA engine to not be in packet command mode
    (2nd gen only)
  * write reset bit in PDC_CTLSTAT before the first read
    in the loop
  * for 2nd gen SATA follow up with FPDMA reset and clearing
    error status registers
- hard reset (pdc_sata_hardreset):
  * wait for ATA engine to not be in packet command mode
    (2nd gen only)
  * reset ATA engine via the PCI control register
  * Tejun's change to use non-waiting hardreset + follow-up SRST

I'm not changing the hotplug mask bits since they are taken care
of by sata_promise's ->freeze() and ->thaw() operations. And I'm
not writing the PMP port # because that's always zero (for now).

Tested here on various controllers. In particular, one disk
which used to timeout and fail to recover from certain hdparm
and smartmonctl commands now works nicely.
Signed-off-by: NMikael Pettersson <mikpe@it.uu.se>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>
      ff7cddf5
    • M
      sata_promise: disable hotplug on 1st gen chips · 0ae6654d
      由 Mikael Pettersson 提交于 
      1st generation Promise SATA chips are prone to generating spurious
hotplug events which can disrupt normal operation. This has been
observed on 20376 and 20378 chips. This patch thus disables hotplug
support on 1st gen chips while leaving it enabled for 2nd gen chips.

The pdc_sata_hotplug_offset() function becomes redundant so it is
removed.

Tested on 1st gen 20376 and 20378 mainboard chips and on a 2nd gen
SATA300 PCI card.
Signed-off-by: NMikael Pettersson <mikpe@it.uu.se>
Tested-by: NKurt Roeckx <kurt@roeckx.be>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>
      0ae6654d
    • T
      libata: fix spurious WARN_ON_ONCE() on port freeze · 4dc738ed
      由 Tejun Heo 提交于 
      Commit 54c38444 makes libata abort qcs
after the port is frozen.  This is necessary to guarantee that TF
registers are accessed after the DMA engine is shutdown after an
error.  However, this triggers WARN_ON_ONCE() check in
ata_qc_complete() spuriously.  Move WARN_ON_ONCE() downwards such that
failing commands while frozen doesn't trigger it.
Signed-off-by: NTejun Heo <tj@kernel.org>
Cc: stable <stable@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>
      4dc738ed
    • T
      ahci: restore pci_intx() handling · 31b239ad
      由 Tejun Heo 提交于 
      Commit a5bfc471 dropped explicit
pci_intx() manipulation from ahci because it seemed unnecessary and
ahci doesn't seem to be the right place to be tweaking it if it were.
This was largely okay but there are exceptions.  There was one on an
embedded platform which was fixed via firmware and now bko#14124
reports it on a HP DL320.

  http://bugzilla.kernel.org/show_bug.cgi?id=14124

I still think this isn't something libata drivers should be caring
about (the only ones which are calling pci_intx() explicitly are
libata ones and one other driver) but for now reverting the change
seems to be the right thing to do.
Signed-off-by: NTejun Heo <tj@kernel.org>
Reported-by: NThomas Jarosch <thomas.jarosch@intra2net.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>
      31b239ad
  7. 11 9月, 2009 5 次提交
  9. 09 9月, 2009 8 次提交
  11. 02 9月, 2009 11 次提交
  13. 01 9月, 2009 1 次提交
    • B
      ata_piix: parallel scanning on PATA needs an extra locking · 60c3be38
      由 Bartlomiej Zolnierkiewicz 提交于 
      Commit log for commit 517d3cc1
("[libata] ata_piix: Enable parallel scan") says:

    This patch turns on parallel scanning for the ata_piix driver.
    This driver is used on most netbooks (no AHCI for cheap storage it seems).
    The scan is the dominating time factor in the kernel boot for these
    devices; with this flag it gets cut in half for the device I used
    for testing (eeepc).
    Alan took a look at the driver source and concluded that it ought to be safe
    to do for this driver.  Alan has also checked with the hardware team.

and it is all true but once we put all things together additional
constraints for PATA controllers show up (some hardware registers
have per-host not per-port atomicity) and we risk misprogramming
the controller.

I used the following test to check whether the issue is real:

  @@ -736,8 +736,20 @@ static void piix_set_piomode(struct ata_
   			(timings[pio][1] << 8);
   	}
   	pci_write_config_word(dev, master_port, master_data);
  -	if (is_slave)
  +	if (is_slave) {
  +		if (ap->port_no == 0) {
  +			u8 tmp = slave_data;
  +
  +			while (slave_data == tmp) {
  +				pci_read_config_byte(dev, slave_port, &tmp);
  +				msleep(50);
  +			}
  +
  +			dev_printk(KERN_ERR, &dev->dev, "PATA parallel scan "
  +				   "race detected\n");
  +		}
   		pci_write_config_byte(dev, slave_port, slave_data);
  +	}

   	/* Ensure the UDMA bit is off - it will be turned back on if
   	   UDMA is selected */

and it indeed triggered the error message.

Lets fix all such races by adding an extra locking to ->set_piomode
and ->set_dmamode methods for PATA controllers.

[ Alan: would be better to take the host lock in libata-core for these
  cases so that we fix all the adapters in one swoop.  "Looks fine as a
  temproary quickfix tho" ]

Cc: Arjan van de Ven <arjan@linux.intel.com>
Acked-by: NAlan Cox <alan@linux.intel.com>
Cc: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
      60c3be38
  15. 12 8月, 2009 6 次提交
  17. 29 7月, 2009 1 次提交