Keep track of how many times we ask the stack to linearize the
skb because the HW cannot handle skbs with more than 8 frags per
segment/single packet.

Change-ID: If455452060963a769bbe6112cba952e79e944b52
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When using something like "ip maddr add ..." to add another unicast mac
address to the netdev, the mac address comes into the set_rx_mode handler
in the multicast list whether it is a unicast or multicast address.
This was confusing the code when it was trying to search for addresses
that needed to be deleted from the VSI, because it was looking for the
VSI unicast address in the netdev unicast list.  The result was that a
new unicast address would get added to the VSI list and then immediately
removed, and would never actually make it down into the hardware.

This patch removes the separation from unicast and multicast in the search
for filters to be deleted.  It also simplifies the logic a little with a
jump to the bottom of the loop when an address is found.  Now it doesn't
matter which netdev list the address is hiding in, we'll check them all.

Change-ID: Ie3685a92427ae7d2212bf948919ce295bc7a874c
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Previously, the driver could call this function and have only true/false
returned, but false could mean multiple things like failure to read
or link was down. This change allows the caller to get all return values
in the call chain bubbled back to the source, which keeps information about
failures from being lost.

Also, in some unlikely scenarios, the firmware can become slow to respond
to admin queue (AQ) queries for link state.  Should the AQ time out,
the driver can detect the state and avoid a link change when there
may have been none.

Change-ID: Ib2ac38407b7880750fb891b392fa77457fe6c21c
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The checksum is not correct on big endian machines so add code to swap it
correctly.

Change-ID: Ic92b886d172a2cbe49f5d7eee1bc78e447023c7b
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NPaul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

During early development, we added the function name to all of the error
strings to make debugging simpler. Now that we've released the driver,
our users should have more comprehensible error messages. So tear the
roof off and give up the __func__. Ow.

Change-ID: I7e1766252c7a032b9af6520da6aff536bdfd533c
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In ethtool, there is a possibility of speed getting set to 0
if advertise is set to 0 (which it is when autoneg is disabled).
We never want this to happen as the firmware will actually attempt
to set the speed to 0 sending link down, so add an extra check
to make sure this doesn't happen.

Change-ID: I62e0eeee2cbf043d8e6f5c9c9f0b92794e877f01
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch extends the size of the text available for the interrupt names.
Without this patch, all the descriptive data available for the Flow
Director interrupts is truncated.

Change-ID: I2ac458f23ac3b4ea8f1edf73edc283b1d3704c7f
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

There was a possibility where the asq_last_status could get through without
update and thus report a previous error.  I don't think we've actually seen
this happen, but this patch will help make sure it doesn't.

Change-ID: I9e33927052a5ee6ea21f80b66d4c4b76c2760b17
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Signed-off-by: NChristopher Pau <christopher.pau@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e_init_pf_fcoe() didn't return anything except 0, it prints enough
error info already, and no driver logic depends on the return value,
so this can be void.

Change-ID: Ie6afad849857d87a7064c42c3cce14c74c2f29d8
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Fix a shift value that was wrong, ending up with a bad bitmask.  Also add
a blank line between two sets of #defines for better readability.

Change-ID: I3e41fa2a2ab904d3a4e6cbf13972ab0036a10601
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Rework an if expression to assure there is no type compare problem between
a size and a possible negative number.

Change-ID: I4921fcc96abfcf69490efce020a9e4007f251c99
Reported-by: NHelin Zhang <helin.zhang@intel.com>
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Early addition of new a device id.

Change-ID: I61a8c8556fdf4f5714be4e4089689e374f30293c
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Explicitly stop the rings belonging to each VF when disabling SR-IOV.
Even though the VFs were gone, and the associated VSIs were removed, the
rings were not stopped, and in some circumstances the hardware would
continue to access the memory formerly used by the rings, causing memory
corruption or DMAR errors, both of which would lead to general malaise
of the kernel.

To relieve this condition, explicitly stop all the rings associated with
each VF before releasing its resources.

Change-ID: I78c05d562c66e7b594b7e48d67860f49b3e5b6ec
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The driver was disabling Wake-on-LAN by default and waiting for the user
to expressly turn it on.  This patch has the driver turning on WoL from
the start if enabled in the hardware config, which matches the behavior
of our other drivers.

Change-ID: I43faedb907f8ba4d1a61b72a7c86072b97af12b1
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In some rare cases the reset can take longer to complete so increase the
amount of time we wait.

Change-ID: Ib5628ec54b526a811ee33d1214fe763226406671
Signed-off-by: NPaul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Some applications use a listen() backlog of 1.

Prior kernels were silently enforcing a qlen_log of 4, so that we were
sending up to /proc/sys/net/ipv4/tcp_synack_retries SYNACK messages.

Fixes: ef547f2a ("tcp: remove max_qlen_log")
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixed an assignment coding style issue
Signed-off-by: NYuvaraja Mariappan <ymariappan@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ursula Braun says:

====================
s390: qeth patches for net-next

here are some s390 related patches for net-next. The qeth patches
are performance optimizations in the driver. The qdio patch corrects
a warning condition.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If HiperSockets Completion Queueing is enabled, qdio always
issues a warning, since the condition is always met.
This patch fixes the condition in WARN_ON_ONCE that was always
true.
Signed-off-by: NEugene Crosser <Eugene.Crosser@ru.ibm.com>
Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In layer2 mode of the qeth driver, MAC address lists
from struct net_device require mapping to the OSA-card.
The existing implementation is inefficient for lists with
more than several MAC addresses, since for every
ndo_set_rx_mode callback it removes all MAC addresses first,
and then registers the current MAC address list.
This patch changes implementation of ndo_set_rx_mode callback
in qeth, only performing hardware registration/removal for
new/deleted addresses. To shorten lookup of MAC addresses
registered addresses are kept in a hashtable instead of a
linear list.
Signed-off-by: NLakhvich Dmitriy <ldmitriy@ru.ibm.com>
Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com>
Reviewed-by: NEugene Crosser <Eugene.Crosser@ru.ibm.com>
Reviewed-by: NThomas Richter <tmricht@de.ibm.com>
Tested-by: NChristian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for GRO (generic receive offload) in the layer 2
part of device driver qeth. This results in a performance
improvement when GRO and RX is turned on.
Signed-off-by: NThomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Nikolay Aleksandrov says:

====================
bridge: netlink: complete port attribute support

This is the second set that completes the bridge port's netlink support and
makes everything from sysfs available via netlink. I've used sysfs as a
guide of what and how to set again. I've tested setting/getting every
option and also this time tested enabling KASAN. Again there're a few long
line warnings about the ifla attribute names in br_port_info_size() but
as the previous set - it's good to know what's been accounted for.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add IFLA_BRPORT_MULTICAST_ROUTER to allow setting/getting port's
multicast_router via netlink.
Signed-off-by: NNikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add IFLA_BRPORT_FLUSH to allow flushing port's fdb similar to sysfs's
flush.
Signed-off-by: NNikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add the following attributes in order to export port's timer values:
IFLA_BRPORT_MESSAGE_AGE_TIMER, IFLA_BRPORT_FORWARD_DELAY_TIMER and
IFLA_BRPORT_HOLD_TIMER.
Signed-off-by: NNikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add IFLA_BRPORT_TOPOLOGY_CHANGE_ACK and IFLA_BRPORT_CONFIG_PENDING to
allow getting port's topology_change_ack and config_pending respectively
via netlink.
Signed-off-by: NNikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add IFLA_BRPORT_(ID|NO) to allow getting port's port_id and port_no
respectively via netlink.
Signed-off-by: NNikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add IFLA_BRPORT_DESIGNATED_(COST|PORT) to allow getting the port's
designated cost and port respectively via netlink.
Signed-off-by: NNikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add IFLA_BRPORT_BRIDGE_ID to allow getting the designated bridge id via
netlink.
Signed-off-by: NNikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add IFLA_BRPORT_ROOT_ID to allow getting the designated root id via
netlink.
Signed-off-by: NNikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the user specifies a VRF device in a get route query the custom route
pointing to the VRF device is returned:

    $ ip route ls table vrf-red
    unreachable default
    broadcast 10.2.1.0 dev eth1  proto kernel  scope link  src 10.2.1.2
    10.2.1.0/24 dev eth1  proto kernel  scope link  src 10.2.1.2
    local 10.2.1.2 dev eth1  proto kernel  scope host  src 10.2.1.2
    broadcast 10.2.1.255 dev eth1  proto kernel  scope link  src 10.2.1.2

    $ ip route get oif vrf-red 10.2.1.40
    10.2.1.40 dev vrf-red
        cache

Add the flags to skip the custom route and go directly to the FIB. With
this patch the actual route is returned:

    $ ip route get oif vrf-red 10.2.1.40
    10.2.1.40 dev eth1  src 10.2.1.2
        cache
Signed-off-by: NDavid Ahern <dsa@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Merge tag 'mac80211-next-for-davem-2015-10-05' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next

Johannes Berg says:

====================
For the current cycle, we have the following right now:
 * many internal fixes, API improvements, cleanups, etc.
 * full AP client state tracking in cfg80211/mac80211 from Ayala
 * VHT support (in mac80211) for mesh
 * some A-MSDU in A-MPDU support from Emmanuel
 * show current TX power to userspace (from Rafał)
 * support for netlink dump in vendor commands (myself)
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

David Ahern says:

====================
net: Add saddr op to l3mdev and vrf

First 2 patches are re-sends of patches that got lost in the ethosphere
Tuesday; they were part of the first round of l3mdev conversions.
Next 3 handle the source address lookup for raw and datagram sockets
bound to a VRF device.

The conversion to the get_saddr op also fixes locally originated TCP
packets showing up at the VRF device. The use of the FLOWI_FLAG_L3MDEV_SRC
flag in ip_route_connect_init was causing locally generated packets
to skip the VRF device.

v2
- rebased to top of net-next per device delete fix and hash based
  multipath patches
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ping originated on box through a VRF device is showing up in tcpdump
without a source address:
    $ tcpdump -n -i vrf-blue
    08:58:33.311303 IP 0.0.0.0 > 10.2.2.254: ICMP echo request, id 2834, seq 1, length 64
    08:58:33.311562 IP 10.2.2.254 > 10.2.2.2: ICMP echo reply, id 2834, seq 1, length 64

Add the call to l3mdev_get_saddr to raw_sendmsg.
Signed-off-by: NDavid Ahern <dsa@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add operation to l3mdev to lookup source address for a given flow.
Add support for the operation to VRF driver and convert existing
IPv4 hooks to use the new lookup.
Signed-off-by: NDavid Ahern <dsa@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

VRF device needs the same path selection following lookup to set source
address. Rather than duplicating code, move existing code into a
function that is exported to modules.

Code move only; no functional change.
Signed-off-by: NDavid Ahern <dsa@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

IPv6 addrconf keys off of IFF_SLAVE so can not use it for L3 slave.
Add a new private flag and add netif_is_l3_slave function for checking
it.
Signed-off-by: NDavid Ahern <dsa@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid Ahern <dsa@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It occurred to me yesterday that 741a11d9 ("net: ipv6: Add
RT6_LOOKUP_F_IFACE flag if oif is set") means that xfrm6_dst_lookup
needs the FLOWI_FLAG_SKIP_NH_OIF flag set. This latest commit causes
the oif to be considered in lookups which is known to break vti. This
explains why 58189ca7 did not the IPv6 change at the time it was
submitted.

Fixes: 42a7b32b ("xfrm: Add oif to dst lookups")
Signed-off-by: NDavid Ahern <dsa@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This enables eTSEC's filer (Rx parser) and the FGPI Rx
interrupt (Filer General Purpose Interrupt) as a wakeup
source event.

Upon entering suspend state, the eTSEC filer is given
a rule to match incoming L2 unicast packets.  A packet
matching the rule will be enqueued in the Rx ring and
a FGPI Rx interrupt will be asserted by the filer to
wakeup the system.  Other packet types will be dropped.
On resume the filer table is restored to the content
before entering suspend state.
The set of rules from gfar_filer_config_wol() could be
extended to implement other WoL capabilities as well.

The "fsl,wake-on-filer" DT binding enables this capability
on certain platforms that feature the necessary power
management infrastructure, targeting mainly printing and
imaging applications.
(refer to Power Management section of the SoC Ref Man)

Cc: Li Yang <leoli@freescale.com>
Cc: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: NClaudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>