Add CONFIG_CPU_FREQ_BOOST_SW Kconfig option such that software-managed
boost is enabled only after selecting "EXYNOS Frequency Overclocking -
Software".  It also depends on the thermal subsystem to be compiled in,
which is necessary for disabling boost and cooling down the device when
overheating is detected.

Software-managed boost _MUST_ _NOT_ be enabled without thermal subsystem
with properly defined overheating temperature thresholds.

This option doesn't affect the x86's hardware-driven boost support
in the acpi-cpufreq driver.
Signed-off-by: NLukasz Majewski <l.majewski@samsung.com>
Signed-off-by: NMyungjoo Ham <myungjoo.ham@samsung.com>
Acked-by: NViresh Kumar <viresh.kumar@linaro.org>
[rjw: Subject and changelog]
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Modify acpi-cpufreq's hardware-based boost solution to work with the
common cpufreq boost framework.
Signed-off-by: NLukasz Majewski <l.majewski@samsung.com>
Signed-off-by: NMyungjoo Ham <myungjoo.ham@samsung.com>
Acked-by: NViresh Kumar <viresh.kumar@linaro.org>
[rjw: Subject and changelog]
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

This commit adds boost frequency support in cpufreq core (Hardware &
Software). Some SoCs (like Exynos4 - e.g. 4x12) allow setting frequency
above its normal operation limits. Such mode shall be only used for a
short time.

Overclocking (boost) support is essentially provided by platform
dependent cpufreq driver.

This commit unifies support for SW and HW (Intel) overclocking solutions
in the core cpufreq driver. Previously the "boost" sysfs attribute was
defined in the ACPI processor driver code. By default boost is disabled.
One global attribute is available at: /sys/devices/system/cpu/cpufreq/boost.

It only shows up when cpufreq driver supports overclocking.
Under the hood frequencies dedicated for boosting are marked with a
special flag (CPUFREQ_BOOST_FREQ) at driver's frequency table.
It is the user's concern to enable/disable overclocking with a proper call
to sysfs.

The cpufreq_boost_trigger_state() function is defined non static on purpose.
It is used later with thermal subsystem to provide automatic enable/disable
of the BOOST feature.
Signed-off-by: NLukasz Majewski <l.majewski@samsung.com>
Signed-off-by: NMyungjoo Ham <myungjoo.ham@samsung.com>
Acked-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Add perf trace event "power:pstate_sample" to report driver state to
aid in diagnosing issues reported against intel_pstate.
Signed-off-by: NDirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

CPUFreq drivers that use clock frameworks interface,i.e. clk_get_rate(),
to get CPUs clk rate, have similar sort of code used in most of them.

This patch adds a generic ->get() which will do the same thing for them.
All those drivers are required to now is to set .get to cpufreq_generic_get()
and set their clk pointer in policy->clk during ->init().
Acked-by: NHans-Christian Egtvedt <egtvedt@samfundet.no>
Acked-by: NShawn Guo <shawn.guo@linaro.org>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NShawn Guo <shawn.guo@linaro.org>
Acked-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

There are some parts of common kernel which would be using routines
like clk_get_rate() on some platforms. Currently, they wouldn't be
called for SA1100 boards, but they are needed for successful kernel
compilation.

Create a dummy clk_get_rate() routine for SA1100 which can be called
by the cpufreq core. More dummy routines might be added later if
necessary.

Cc: Russell King <linux@arm.linux.org.uk>
Cc: Arnd Bergmann <arnd.bergmann@linaro.org>
Reported-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>
[rjw: Changelog]
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

When cpufreq_stats is compiled in as a module, cpufreq driver would
have already been registered. And so the CPUFREQ_CREATE_POLICY
notifiers wouldn't be called for it. Hence no sysfs entries for stats. :(

This patch calls cpufreq_stats_create_table() for each online CPU from
cpufreq_stats_init() and so if policy is already created for CPUx then
we will register sysfs stats for it.

When its not compiled as module, we will return early as policy wouldn't
be found for any of the CPUs.
Acked-by: NNicolas Pitre <nico@linaro.org>
Tested-by: NNicolas Pitre <nico@linaro.org>
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

We don't have code paths now where we need to do these two things
separately, so it is better do them in a single routine. Just as
they are allocated in a single routine.
Acked-by: NNicolas Pitre <nico@linaro.org>
Tested-by: NNicolas Pitre <nico@linaro.org>
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Either CPUs are hot-unplugged or suspend/resume occurs, cpufreq core
will send notifications to cpufreq-stats and stats structure and sysfs
entries would be correctly handled..

And so we don't actually need hotcpu notifiers in cpufreq-stats anymore.
We were only handling cpu hot-unplug events here and that are already
taken care of by POLICY notifiers.
Acked-by: NNicolas Pitre <nico@linaro.org>
Tested-by: NNicolas Pitre <nico@linaro.org>
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

There are several problems with cpufreq stats in the way it handles
cpufreq_unregister_driver() and suspend/resume..

 - We must not lose data collected so far when suspend/resume happens
   and so stats directories must not be removed/allocated during these
   operations, which is done currently.

 - cpufreq_stat has registered notifiers with both cpufreq and hotplug.
   It adds sysfs stats directory with a cpufreq notifier: CPUFREQ_NOTIFY
   and removes this directory with a notifier from hotplug core.

   In case cpufreq_unregister_driver() is called (on rmmod cpufreq driver),
   stats directories per cpu aren't removed as CPUs are still online. The
   only call cpufreq_stats gets is cpufreq_stats_update_policy_cpu() for
   all CPUs except the last of each policy. And pointer to stat information
   is stored in the entry for last CPU in the per-cpu cpufreq_stats_table.
   But policy structure would be freed inside cpufreq core and so that will
   result in memory leak inside cpufreq stats (as we are never freeing
   memory for stats).

   Now if we again insert the module cpufreq_register_driver() will be
   called and we will again allocate stats data and put it on for first
   CPU of every policy.  In case we only have a single CPU per policy, we
   will return with a error from cpufreq_stats_create_table() due to this
   code:

	if (per_cpu(cpufreq_stats_table, cpu))
		return -EBUSY;

   And so probably cpufreq stats directory would not show up anymore (as
   it was added inside last policies->kobj which doesn't exist anymore).
   I haven't tested it, though. Also the values in stats files wouldn't
   be refreshed as we are using the earlier stats structure.

 - CPUFREQ_NOTIFY is called from cpufreq_set_policy() which is called for
   scenarios where we don't really want cpufreq_stat_notifier_policy() to get
   called. For example whenever we are changing anything related to a policy:
   min/max/current freq, etc. cpufreq_set_policy() is called and so cpufreq
   stats is notified. Where we don't do any useful stuff other than simply
   returning with -EBUSY from cpufreq_stats_create_table(). And so this
   isn't the right notifier that cpufreq stats..

 Due to all above reasons this patch does following changes:
 - Add new notifiers CPUFREQ_CREATE_POLICY and CPUFREQ_REMOVE_POLICY,
   which are only called when policy is created/destroyed. They aren't
   called for suspend/resume paths..
 - Use these notifiers in cpufreq_stat_notifier_policy() to create/destory
   stats sysfs entries. And so cpufreq_unregister_driver() or suspend/resume
   shouldn't be a problem for cpufreq_stats.
 - Return early from cpufreq_stat_cpu_callback() for suspend/resume sequence,
   so that we don't free stats structure.
Acked-by: NNicolas Pitre <nico@linaro.org>
Tested-by: NNicolas Pitre <nico@linaro.org>
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

The only caller of speedstep_get_state() was removed in commit d4019f0a
("cpufreq: move freq change notifications to cpufreq core"). So building
speedstep-smi.o now triggers a GCC warning:
    drivers/cpufreq/speedstep-smi.c:148:12: warning: 'speedstep_get_state' defined but not used [-Wunused-function]

Remove this unused function.
Signed-off-by: NPaul Bolle <pebolle@tiscali.nl>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

KVM environments do not support APERF/MPERF MSRs. intel_pstate cannot
operate without these registers.

The previous validity checks in intel_pstate_msrs_not_valid() are
insufficent in nested KVMs.

References: https://bugzilla.redhat.com/show_bug.cgi?id=1046317Signed-off-by: NDirk Brandewie <dirk.j.brandewie@intel.com>
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

This patch reorders reported frequencies from the highest to the lowest,
just like in other frequency drivers.
Signed-off-by: NMikulas Patocka <mpatocka@redhat.com>
Acked-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

The powernow-k6 driver used to read the initial multiplier from the
powernow register. However, there is a problem with this:

* If there was a frequency transition before, the multiplier read from the
  register corresponds to the current multiplier.
* If there was no frequency transition since reset, the field in the
  register always reads as zero, regardless of the current multiplier that
  is set using switches on the mainboard and that the CPU is running at.

The zero value corresponds to multiplier 4.5, so as a consequence, the
powernow-k6 driver always assumes multiplier 4.5.

For example, if we have 550MHz CPU with bus frequency 100MHz and
multiplier 5.5, the powernow-k6 driver thinks that the multiplier is 4.5
and bus frequency is 122MHz. The powernow-k6 driver then sets the
multiplier to 4.5, underclocking the CPU to 450MHz, but reports the
current frequency as 550MHz.

There is no reliable way how to read the initial multiplier. I modified
the driver so that it contains a table of known frequencies (based on
parameters of existing CPUs and some common overclocking schemes) and sets
the multiplier according to the frequency. If the frequency is unknown
(because of unusual overclocking or underclocking), the user must supply
the bus speed and maximum multiplier as module parameters.

This patch should be backported to all stable kernels. If it doesn't
apply cleanly, change it, or ask me to change it.
Signed-off-by: NMikulas Patocka <mpatocka@redhat.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

I found out that a system with k6-3+ processor is unstable during network
server load. The system locks up or the network card stops receiving. The
reason for the instability is the CPU frequency scaling.

During frequency transition the processor is in "EPM Stop Grant" state.
The documentation says that the processor doesn't respond to inquiry
requests in this state. Consequently, coherency of processor caches and
bus master devices is not maintained, causing the system instability.

This patch flushes the cache during frequency transition. It fixes the
instability.

Other minor changes:
* u64 invalue changed to unsigned long because the variable is 32-bit
* move the logic to set the multiplier to a separate function
  powernow_k6_set_cpu_multiplier
* preserve lower 5 bits of the powernow port instead of 4 (the voltage
  field has 5 bits)
* mask interrupts when reading the multiplier, so that the port is not
  open during other activity (running other kernel code with the port open
  shouldn't cause any misbehavior, but we should better be safe and keep
  the port closed)

This patch should be backported to all stable kernels. If it doesn't
apply cleanly, change it, or ask me to change it.
Signed-off-by: NMikulas Patocka <mpatocka@redhat.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Add a Documentation/ABI entry for
/sys/devices/system/cpu/intel_pstate/max_perf_pct,
/sys/devices/system/cpu/intel_pstate/min_perf_pct, and
/sys/devices/system/cpu/intel_pstate/no_turbo.

Cc: Dirk Brandewie <dirk.brandewie@gmail.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: NRamkumar Ramachandra <artagnon@gmail.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

To make the driver multiplatform-friendly, unconditional initialization
in an initcall is replaced with a platform driver probed only if
respective platform device is registered.

Tested at: Exynos4210 (TRATS) and Exynos4412 (TRATS2)
Signed-off-by: NLukasz Majewski <l.majewski@samsung.com>
Signed-off-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: NSachin Kamat <sachin.kamat@linaro.org>
Tested-by: NSachin Kamat <sachin.kamat@linaro.org>
Acked-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Sometimes boot loaders set CPU frequency to a value outside of frequency table
present with cpufreq core. In such cases CPU might be unstable if it has to run
on that frequency for long duration of time and so its better to set it to a
frequency which is specified in freq-table. This also makes cpufreq stats
inconsistent as cpufreq-stats would fail to register because current frequency
of CPU isn't found in freq-table.

Because we don't want this change to affect boot process badly, we go for the
next freq which is >= policy->cur ('cur' must be set by now, otherwise we will
end up setting freq to lowest of the table as 'cur' is initialized to zero).

In case current frequency doesn't match any frequency from freq-table, we throw
warnings to user, so that user can get this fixed in their bootloaders or
freq-tables.
Reported-by: NCarlos Hernandez <ceh@ti.com>
Reported-and-tested-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Sometimes boot loaders set CPU frequency to a value outside of frequency table
present with cpufreq core. In such cases CPU might be unstable if it has to run
on that frequency for long duration of time and so its better to set it to a
frequency which is specified in frequency table.

On some systems we can't really say what frequency we're running at the moment
and so for these we shouldn't check if we are running at a frequency present in
frequency table. And so we really can't force this for all the cpufreq drivers.

Hence we are created another flag here: CPUFREQ_NEED_INITIAL_FREQ_CHECK that
will be marked by platforms which want to go for this check at boot time.

Initially this is done for all ARM platforms but others may follow if required.
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Add a routine check to see if the platform supplied the OPP table.
Incase there's no OPP table exist, it will try to initialise it.

It's been tested on iMX6SL board where the platform doesn't have
an OPP table.
Signed-off-by: NJohn Tobias <john.tobias.ph@gmail.com>
Acked-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

The imx6q-cpufreq driver nowadays is not only running on imx6q but also
other i.MX6 series SoCs like imx6dl and imx6sl.  Update Kconfig prompt
and help text to make it clear to users.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Acked-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

on i.MX6Q, cpu freq change need to follow below flows:

1. each setpoint has different VDDARM, VDDSOC/PU voltage, get the setpoint
   table from dts;
2. when cpu freq is scaling up, need to increase VDDSOC/PU voltage before
   VDDARM, if VDDPU is off, no need to change it;
3. when cpu freq is scaling down, need to decrease VDDARM voltage before
   VDDSOC/PU, if VDDPU is off, no need to change it;

normally dts will pass vddsoc/pu freq/volt info to kernel, if not, will
use fixed value for vddsoc/pu voltage setting.
Signed-off-by: NAnson Huang <b20788@freescale.com>
Acked-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

In the current code, if we fail during a frequency transition, we
simply send the POSTCHANGE notification with the old frequency. This
isn't enough.

One of the core users of these notifications is the code responsible
for keeping loops_per_jiffy aligned with frequency changes. And mostly
it is written as:

	if ((val == CPUFREQ_PRECHANGE  && freq->old < freq->new) ||
	    (val == CPUFREQ_POSTCHANGE && freq->old > freq->new)) {
		update-loops-per-jiffy...
	}

So, suppose we are changing to a higher frequency and failed during
transition, then following will happen:
- CPUFREQ_PRECHANGE notification with freq-new > freq-old
- CPUFREQ_POSTCHANGE notification with freq-new == freq-old

The first one will update loops_per_jiffy and second one will do
nothing. Even if we send the 2nd notification by exchanging values of
freq-new and old, some users of these notifications might get
unstable.

This can be fixed by simply calling cpufreq_notify_post_transition()
with error code and this routine will take care of sending
notifications in the correct order.
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>
[rjw: Folded 3 patches into one, rebased unicore2 changes]
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

This introduces a new routine cpufreq_notify_post_transition() which
can be used to send POSTCHANGE notification for new freq with or
without both {PRE|POST}CHANGE notifications for last freq. This is
useful at multiple places, especially for sending transition failure
notifications.
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Use common clock framework (CCF) APIs to set the clock rates
instead of direct register manipulation. This now updates the
sysfs entry (cpuinfo_cur_freq) correctly which did not reflect
the correct value until now. While at it clean up the PLL s-div
parameter setting as it is handled by the PLL driver.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Acked-by: NViresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: NLukasz Majewski <l.majewski@samsung.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

When a CPU is hot removed we'll cancel all the delayed work items via
gov_cancel_work(). Sometimes the delayed work function determines that
it should adjust the delay for all other CPUs that the policy is
managing. If this scenario occurs, the canceling CPU will cancel its own
work but queue up the other CPUs works to run.

Commit 3617f2 (cpufreq: Fix timer/workqueue corruption due to double
queueing) has tried to fix this, but reading governor_enabled is not
protected by cpufreq_governor_lock. Even though od_dbs_timer() checks
governor_enabled before gov_queue_work(), this scenario may occur. For
example:

 CPU0                                        CPU1
 ----                                        ----
 cpu_down()
  ...                                        <work runs>
  __cpufreq_remove_dev()                     od_dbs_timer()
   __cpufreq_governor()                       policy->governor_enabled
    policy->governor_enabled = false;
    cpufreq_governor_dbs()
     case CPUFREQ_GOV_STOP:
      gov_cancel_work(dbs_data, policy);
       cpu0 work is canceled
        timer is canceled
        cpu1 work is canceled
        <waits for cpu1>
                                              gov_queue_work(*, *, true);
                                               cpu0 work queued
                                               cpu1 work queued
                                               cpu2 work queued
                                               ...
        cpu1 work is canceled
        cpu2 work is canceled
        ...

At the end of the GOV_STOP case cpu0 still has a work queued to
run although the code is expecting all of the works to be
canceled. __cpufreq_remove_dev() will then proceed to
re-initialize all the other CPUs works except for the CPU that is
going down. The CPUFREQ_GOV_START case in cpufreq_governor_dbs()
will trample over the queued work and debugobjects will spit out
a warning:

WARNING: at lib/debugobjects.c:260 debug_print_object+0x94/0xbc()
ODEBUG: init active (active state 0) object type: timer_list hint: delayed_work_timer_fn+0x0/0x14
Modules linked in:
CPU: 1 PID: 1205 Comm: sh Tainted: G        W    3.10.0 #200
[<c01144f0>] (unwind_backtrace+0x0/0xf8) from [<c0111d98>] (show_stack+0x10/0x14)
[<c0111d98>] (show_stack+0x10/0x14) from [<c01272cc>] (warn_slowpath_common+0x4c/0x68)
[<c01272cc>] (warn_slowpath_common+0x4c/0x68) from [<c012737c>] (warn_slowpath_fmt+0x30/0x40)
[<c012737c>] (warn_slowpath_fmt+0x30/0x40) from [<c034c640>] (debug_print_object+0x94/0xbc)
[<c034c640>] (debug_print_object+0x94/0xbc) from [<c034c7f8>] (__debug_object_init+0xc8/0x3c0)
[<c034c7f8>] (__debug_object_init+0xc8/0x3c0) from [<c01360e0>] (init_timer_key+0x20/0x104)
[<c01360e0>] (init_timer_key+0x20/0x104) from [<c04872ac>] (cpufreq_governor_dbs+0x1dc/0x68c)
[<c04872ac>] (cpufreq_governor_dbs+0x1dc/0x68c) from [<c04833a8>] (__cpufreq_governor+0x80/0x1b0)
[<c04833a8>] (__cpufreq_governor+0x80/0x1b0) from [<c0483704>] (__cpufreq_remove_dev.isra.12+0x22c/0x380)
[<c0483704>] (__cpufreq_remove_dev.isra.12+0x22c/0x380) from [<c0692f38>] (cpufreq_cpu_callback+0x48/0x5c)
[<c0692f38>] (cpufreq_cpu_callback+0x48/0x5c) from [<c014fb40>] (notifier_call_chain+0x44/0x84)
[<c014fb40>] (notifier_call_chain+0x44/0x84) from [<c012ae44>] (__cpu_notify+0x2c/0x48)
[<c012ae44>] (__cpu_notify+0x2c/0x48) from [<c068dd40>] (_cpu_down+0x80/0x258)
[<c068dd40>] (_cpu_down+0x80/0x258) from [<c068df40>] (cpu_down+0x28/0x3c)
[<c068df40>] (cpu_down+0x28/0x3c) from [<c068e4c0>] (store_online+0x30/0x74)
[<c068e4c0>] (store_online+0x30/0x74) from [<c03a7308>] (dev_attr_store+0x18/0x24)
[<c03a7308>] (dev_attr_store+0x18/0x24) from [<c0256fe0>] (sysfs_write_file+0x100/0x180)
[<c0256fe0>] (sysfs_write_file+0x100/0x180) from [<c01fec9c>] (vfs_write+0xbc/0x184)
[<c01fec9c>] (vfs_write+0xbc/0x184) from [<c01ff034>] (SyS_write+0x40/0x68)
[<c01ff034>] (SyS_write+0x40/0x68) from [<c010e200>] (ret_fast_syscall+0x0/0x48)

In gov_queue_work(), lock cpufreq_governor_lock before gov_queue_work,
and unlock it after __gov_queue_work(). In this way, governor_enabled
is guaranteed not changed in gov_queue_work().
Signed-off-by: NJane Li <jiel@marvell.com>
Acked-by: NViresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Local variable used only in this file is made static.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Acked-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Local variables used only in this file are made static.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Acked-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

The contents of this header file are not referenced in the driver.
Remove its inclusion.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Acked-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

The arm_big_little cpufreq driver is only used by ARM bigLITTLE
platforms and hence must depend on CONFIG_BIG_LITTLE.

This was highlighted by Russell earlier when he reported this issue:

drivers/built-in.o: In function `bL_cpufreq_set_rate':
powercap_sys.c:(.text+0x5ed9a0): undefined reference to `bL_switch_request_cb'
Reported-by: NRussell King <linux@arm.linux.org.uk>
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

The Intel P-state driver is currently undocumented. Add some
documentation based on the cover-letter sent with the original series.

Cc: Dirk Brandewie <dirk.brandewie@gmail.com>
Acked-by: NRandy Dunlap <rdunlap@infradead.org>
Signed-off-by: NRamkumar Ramachandra <artagnon@gmail.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Pull battery fixes from Anton Vorontsov:
 "Two fixes:

   - fix build error caused by max17042_battery conversion to the regmap
     API.

   - fix kernel oops when booting with wakeup_source_activate enabled"

* tag 'for-v3.13-fixes' of git://git.infradead.org/battery-2.6:
  max17042_battery: Fix build errors caused by missing REGMAP_I2C config
  power_supply: Fix Oops from NULL pointer dereference from wakeup_source_activate

Pull ACPI and PM fixes and new device IDs from Rafael Wysocki:
 "These commits, except for one, are regression fixes and the remaining
  one fixes a divide error leading to a kernel panic.  The majority of
  the regressions fixed here were introduced during the 3.12 cycle, one
  of them is from this cycle and one is older.

  Specifics:

   - VGA switcheroo was broken for some users as a result of the
     ACPI-based PCI hotplug (ACPIPHP) changes in 3.12, because some
     previously ignored hotplug events started to be handled.  The fix
     causes them to be ignored again.

   - There are two more issues related to cpufreq's suspend/resume
     handling changes from the 3.12 cycle addressed by Viresh Kumar's
     fixes.

   - intel_pstate triggers a divide error in a timer function if the
     P-state information it needs is missing during initialization.
     This leads to kernel panics on nested KVM clients and is fixed by
     failing the initialization cleanly in those cases.

   - PCI initalization code changes during the 3.9 cycle uncovered BIOS
     issues related to ACPI wakeup notifications (some BIOSes send them
     for devices that aren't supposed to support ACPI wakeup).  Work
     around them by installing an ACPI wakeup notify handler for all PCI
     devices with ACPI support.

   - The Calxeda cpuilde driver's probe function is tagged as __init,
     which is incorrect and causes a section mismatch to occur during
     build.  Fix from Andre Przywara removes the __init tag from there.

   - During the 3.12 cycle ACPIPHP started to print warnings about
     missing _ADR for devices that legitimately don't have it.  Fix from
     Toshi Kani makes it only print the warnings where they make sense"

* tag 'pm+acpi-3.13-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  ACPIPHP / radeon / nouveau: Fix VGA switcheroo problem related to hotplug
  intel_pstate: Fail initialization if P-state information is missing
  ARM/cpuidle: remove __init tag from Calxeda cpuidle probe function
  PCI / ACPI: Install wakeup notify handlers for all PCI devs with ACPI
  cpufreq: preserve user_policy across suspend/resume
  cpufreq: Clean up after a failing light-weight initialization
  ACPI / PCI / hotplug: Avoid warning when _ADR not present

Pull kvm bugfixes from Marcelo Tosatti.

* git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: nVMX: Unconditionally uninit the MMU on nested vmexit
  KVM: x86: Fix APIC map calculation after re-enabling

Merge patches from Andrew Morton:
 "Ten fixes"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
  epoll: do not take the nested ep->mtx on EPOLL_CTL_DEL
  sh: add EXPORT_SYMBOL(min_low_pfn) and EXPORT_SYMBOL(max_low_pfn) to sh_ksyms_32.c
  drivers/dma/ioat/dma.c: check DMA mapping error in ioat_dma_self_test()
  mm/memory-failure.c: transfer page count from head page to tail page after split thp
  MAINTAINERS: set up proper record for Xilinx Zynq
  mm: remove bogus warning in copy_huge_pmd()
  memcg: fix memcg_size() calculation
  mm: fix use-after-free in sys_remap_file_pages
  mm: munlock: fix deadlock in __munlock_pagevec()
  mm: munlock: fix a bug where THP tail page is encountered

The EPOLL_CTL_DEL path of epoll contains a classic, ab-ba deadlock.
That is, epoll_ctl(a, EPOLL_CTL_DEL, b, x), will deadlock with
epoll_ctl(b, EPOLL_CTL_DEL, a, x).  The deadlock was introduced with
commmit 67347fe4 ("epoll: do not take global 'epmutex' for simple
topologies").

The acquistion of the ep->mtx for the destination 'ep' was added such
that a concurrent EPOLL_CTL_ADD operation would see the correct state of
the ep (Specifically, the check for '!list_empty(&f.file->f_ep_links')

However, by simply not acquiring the lock, we do not serialize behind
the ep->mtx from the add path, and thus may perform a full path check
when if we had waited a little longer it may not have been necessary.
However, this is a transient state, and performing the full loop
checking in this case is not harmful.

The important point is that we wouldn't miss doing the full loop
checking when required, since EPOLL_CTL_ADD always locks any 'ep's that
its operating upon.  The reason we don't need to do lock ordering in the
add path, is that we are already are holding the global 'epmutex'
whenever we do the double lock.  Further, the original posting of this
patch, which was tested for the intended performance gains, did not
perform this additional locking.
Signed-off-by: NJason Baron <jbaron@akamai.com>
Cc: Nathan Zimmer <nzimmer@sgi.com>
Cc: Eric Wong <normalperson@yhbt.net>
Cc: Nelson Elhage <nelhage@nelhage.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Davide Libenzi <davidel@xmailserver.org>
Cc: "Paul E. McKenney" <paulmck@us.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Min_low_pfn and max_low_pfn were used in pfn_valid macro if defined
CONFIG_FLATMEM.  When the functions that use the pfn_valid is used in
driver module, max_low_pfn and min_low_pfn is to undefined, and fail to
build.

  ERROR: "min_low_pfn" [drivers/block/aoe/aoe.ko] undefined!
  ERROR: "max_low_pfn" [drivers/block/aoe/aoe.ko] undefined!
  make[2]: *** [__modpost] Error 1
  make[1]: *** [modules] Error 2

This patch fix this problem.
Signed-off-by: NNobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Cc: Kuninori Morimoto <kuninori.morimoto.gx@gmail.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>