Some RV100 cards with 2 VGA ports show up with DVI+VGA, however
some boards with DVI+VGA have the same subsystem ids. Better
to have a VGA port show up as DVI than having a non-useable
DVI port.

reported by DHR in irc.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

For some reason on resume, executing the BIOS scripts locks up the whole chipset, by avoiding the dynclk table the machine resumes properly and seems to function okay.
Signed-off-by: NDave Airlie <airlied@redhat.com>

This works well enough on a js21, but it would be nice if IBM could supply
more tables for the later Power6/7 machines.
Signed-off-by: NDave Airlie <airlied@redhat.com>

We really don't want to be polling tv-out but since we weren't forcing the
i2c lines to invalid (tv-out has no DDC), we were adding tv connectors to the
polling setup and this was causing blinking on secondary displays.

This fixes the regression Torsten reported.
Reported-by: NTorsten Kaiser <just.for.lkml@googlemail.com>
Tested-by: NTorsten Kaiser <just.for.lkml@googlemail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Noticed by Rafał Miłecki.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

- Enable GPIO voltage for non pm modes as well so resetting
the default voltage works.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

- Use radeon hpd enum consistently (in both hotplug and dp)
- Legacy r100 with DVI should be HPD_1 not NONE
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

The lowest power states often cause display problems, so only enable
them when all displays are off.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

- remove non_clock_info struct
- track power state misc flags
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This also simplifies the code and enables reclocking with multiple heads
active by tracking whether the power states are single or multi-head
capable.

Eventually, we will want to select a power state based on external
factors (AC/DC state, user selection, etc.).

(v2) Update for evergreen
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Should work better on some panels.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Some vbios dac_adj tables are all zeros.  Check for that
case and use the default table if so.

Should fix fdo bug 27478.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NAdam Jackson <ajax@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

fixing the i2c prescale in the last patch
gets it working on r1xx.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

The bios has alternate pll output limits for LCD panels.
If available, use these for pll divider calculations.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

We kept pointers to requested and current clock modes in every power state.
That was useless, more /global/ pointers in power struct are enough.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Reviewed-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Fixes fdo bug #26329
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Tested-by: NTobias Jakobi <liquid.acid@gmx.net>
Signed-off-by: NDave Airlie <airlied@redhat.com>

It's happened time and time again (most recently with the support for EDID
hardcoded in the BIOS ROM) that new code didn't check for rdev->bios being
non-NULL before triggering dereferences of it. This would result in an
oops/panic on setups with no BIOS ROM. Hopefully this central test will be
more robust.
Signed-off-by: NMichel Dänzer <daenzer@vmware.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

machine is compatible is an OF-specific call.  It should have
the of_ prefix to protect the global namespace.
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Acked-by: NMichal Simek <monstr@monstr.eu>

This adds initial Evergreen KMS support, it doesn't include
any acceleration features or interrupt handling yet.

Major changes are DCE4 handling for PLLs for the > 2 crtcs.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

The idea is to flag a power state with a certain type and use
that type to decide on what state to select.  On r6xx+, we
select a state and then transition between clock modes in that
state.  On pre-r6xx, we transition between states directly.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

The general idea is to validate the current hw state
against the set of power states and select a power
state based on that.  This patch just pulls the power
states from the bios and prints the information.  It
is not currently hooked up in the actual power management
code.  Hooking it up will require reworking the the current
power state selection code and will be handled in a future
patch.

Additionally, we'd need to decide on some default lower
power states for cards without power tables.

v2 - increment state_index after checking for default state
v3 - fix typo in pm init on pre-atom cards, handle pre-atom
cards without x86 bioses
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Some servers hardcode an edid in rom so that they will
work properly with KVMs.  This is a port of the relevant
code from the ddx.

[airlied: reworked to validate edid at boot stage - and
remove special quirk, if there is a valid EDID in the BIOS rom
we'll just try and use it.]
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

wire hw i2c support into radeon i2c algo.

fixes merged:
- handle bus probing correctly
- use meaningful error numbers
- abort if transaction fails
- The line mapping is different depending on the asic.
- protect hw i2c engine with a mutex
- rs300 doesn't have a pin select bit
- r200 has a different pin select setup
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Currently just a wrapper around bit algo
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

drivers/gpu/drm/radeon/radeon_combios.c: In function 'radeon_combios_get_lvds_info':
drivers/gpu/drm/radeon/radeon_combios.c:893: warning: comparison is always false due to limited range of data type

Cc: Dave Airlie <airlied@linux.ie>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NMichel Dänzer <daenzer@vmware.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This detects if the sideport memory is enabled and
if it is VRAM is evicted on suspend/resume.

This should fix s/r issues on some IGPs.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Look up primary dac adj values from the table if
there is no bios or bios dac table to reference.

The lookup table may need to be adjusted for certain
families.

Should fix kernel bug 14945.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

we were just using 1 before.

reported on irc by soreau
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This populates the connectors with HPD (Hot Plug Detect)
information.  This will be used in subsequent patches
for automatic digital monitor connect/disconnect handling.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

- keep the atom i2c id in the i2c rec
- fix gpio regs for GPIO and MDGPIO on pre-avivo chips
- track whether the i2c line is hw capable
- track whether the i2c line uses the multimedia i2c block
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

If the chip isn't initialised properly this can happen.
also fix return value in combios clocks function.
Signed-off-by: NDave Airlie <airlied@redhat.com>

doesn't have a tv-out port
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This enables initialization of external tmds chips on pre-atom
and mac systems.  Macs are untested.  Also, some macs have single
link tmds chips while others have dual link tmds chips.  We need
to figure out which ones have which.

This gets external TMDS working on my RS485 and RV380.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

- Change reg/mask names to match what we use internally
and in the bios
- Clarify how i2c over gpio on radeon actually works
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This will be useful for mode validation and certain
atom tables.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Doesn't have a tv-out port
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

doesn't have a tv-out port
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Original radeon didn't have a connector table in the
bios.  Check for the CRT table and if we have one,
add a VGA connector.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@linux.ie>