The fixup_pv_table assumes that the instructions are in the same
endian configuration as the data, but when the CPU is running in
BE8 the instructions stay in little-endian format.

Make sure if CONFIG_CPU_ENDIAN_BE8 is set that we do all the
alterations to the instructions taking in to account the LDR/STR
will be swapping the data endian-ness.

Since the code is only modifying a byte, we avoid dual-swapping
the data, and just change the bits we clear and ORR in (in the
case where the code is not thumb2).

For thumb2, we add the necessary rev16 instructions to ensure that
the instructions are processed in the correct format, as it was
easier than re-writing the code to contain a mask and shift.
Signed-off-by: NBen Dooks <ben.dooks@codethink.co.uk>
Reviewed-by: NDave Martin <Dave.Martin@arm.com>
Tested-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>

Add ARM_BE8() helper to wrap any code conditional on being
compile when CONFIG_ARM_ENDIAN_BE8 is selected and convert
existing places where this is to use it.
Acked-by: NNicolas Pitre <nico@linaro.org>
Reviewed-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NBen Dooks <ben.dooks@codethink.co.uk>

The Kconfig for arch/arm/mach-ixp4xx has a local definition
of ARCH_SUPPORTS_BIG_ENDIAN which could be used elsewhere.
This means that if IXP4xx is selected and this symbol is
selected eleswhere then an warning is produced.

Clean the following error up by making the symbol be
selected by the main ARCH_IXP4XX definition and have a
common definition in arch/arm/mm/Kconfig

warning: (ARCH_xxx) selects ARCH_SUPPORTS_BIG_ENDIAN which has unmet direct dependencies (ARCH_IXP4XX)
warning: (ARCH_xxx) selects ARCH_SUPPORTS_BIG_ENDIAN which has unmet direct dependencies (ARCH_IXP4XX)
Signed-off-by: NBen Dooks <ben.dooks@codethink.co.uk>

This reverts commit 07f9b61c.

07f9b61c was intended to be a cleanup that didn't change anything, but in
fact, for systems without _CBA (which is almost everything), it broke
extended config space for domain 0 and all config space for other domains.

Reference: http://lkml.kernel.org/r/20131004011806.GE20450@dangermouse.emea.sgi.comReported-by: NHedi Berriche <hedi@sgi.com>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>

When we do a treclaim or trecheckpoint we end up running with userspace
PPR and DSCR values.  Currently we don't do anything special to avoid
running with user values which could cause a severe performance
degradation.

This patch moves the PPR and DSCR save and restore around treclaim and
trecheckpoint so that we run with user values for a much shorter period.
More care is taken with the PPR as it's impact is greater than the DSCR.

This is similar to user exceptions, where we run HTM_MEDIUM early to
ensure that we don't run with a userspace PPR values in the kernel.
Signed-off-by: NMichael Neuling <mikey@neuling.org>
Cc: <stable@vger.kernel.org> # 3.9+
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

We can't take IRQs in tm_reclaim as we might have a bogus r13 and r1.

This turns IRQs hard off in this function.
Signed-off-by: NMichael Neuling <mikey@neuling.org>
Cc: <stable@vger.kernel.org> # 3.9+
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Commit 4df48999 "Add power8 EBB support" included a bug in the handling
of the FAB_CRESP_MATCH and FAB_TYPE_MATCH fields.

These values are pulled out of the event code using EVENT_THR_CTL_SHIFT,
however we were then or'ing that value directly into MMCR1.

This meant we were failing to set the FAB fields correctly, and also
potentially corrupting the value for PMC4SEL. Leading to no counts for
the FAB events and incorrect counts for PMC4.

The fix is simply to shift left the FAB value correctly before or'ing it
with MMCR1.
Reported-by: NSooraj Ravindran Nair <soonair3@in.ibm.com>
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>
Cc: <stable@vger.kernel.org> # 3.10+
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

modalias_show() should return an empty string on error, not -ENODEV.

This causes the following false and annoying error:

> find /sys/devices -name modalias -print0 | xargs -0 cat >/dev/null
cat: /sys/devices/vio/4000/modalias: No such device
cat: /sys/devices/vio/4001/modalias: No such device
cat: /sys/devices/vio/4002/modalias: No such device
cat: /sys/devices/vio/4004/modalias: No such device
cat: /sys/devices/vio/modalias: No such device
Signed-off-by: NPrarit Bhargava <prarit@redhat.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
CC: <stable@vger.kernel.org>

Under heavy (DLPAR?) stress, we tripped this panic() in
arch/powerpc/kernel/iommu.c::iommu_init_table():

	page = alloc_pages_node(nid, GFP_ATOMIC, get_order(sz));
	if (!page)
		panic("iommu_init_table: Can't allocate %ld bytes\n", sz);

Before the panic() we got a page allocation failure for an order-2
allocation. There appears to be memory free, but perhaps not in the
ATOMIC context. I looked through all the call-sites of
iommu_init_table() and didn't see any obvious reason to need an ATOMIC
allocation. Most call-sites in fact have an explicit GFP_KERNEL
allocation shortly before the call to iommu_init_table(), indicating we
are not in an atomic context. There is some indirection for some paths,
but I didn't see any locks indicating that GFP_KERNEL is inappropriate.

With this change under the same conditions, we have not been able to
reproduce the panic.
Signed-off-by: NNishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
CC: <stable@vger.kernel.org>

arch/powerpc/kernel/sysfs.c exports PURR with write permission.
This may be valid for kernel in phyp mode. But writing to
the file in guest mode causes crash due to a priviledge violation
Signed-off-by: NMadhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
CC: <stable@vger.kernel.org>

The csum_partial_copy_generic() function saves the PowerPC non-volatile
r14, r15, and r16 registers for the main checksum-and-copy loop.
Unfortunately, it fails to restore them upon error exit from this loop,
which results in silent corruption of these registers in the presumably
rare event of an access exception within that loop.

This commit therefore restores these register on error exit from the loop.
Signed-off-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: NAnton Blanchard <anton@samba.org>
Cc: stable@vger.kernel.org
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The csum_partial_copy_generic() uses register r7 to adjust the remaining
bytes to process.  Unfortunately, r7 also holds a parameter, namely the
address of the flag to set in case of access exceptions while reading
the source buffer.  Lacking a quantum implementation of PowerPC, this
commit instead uses register r9 to do the adjusting, leaving r7's
pointer uncorrupted.
Signed-off-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: NAnton Blanchard <anton@samba.org>
Cc: stable@vger.kernel.org
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Previous commit 46723bfa... introduced a new config option
HAVE_BOOTMEM_INFO_NODE that ended up breaking memory hot-remove for ppc
when sparse vmemmap is not defined.

This patch defines HAVE_BOOTMEM_INFO_NODE for ppc and adds the call to
register_page_bootmem_info_node. Without this we get a BUG_ON for memory
hot remove in put_page_bootmem().

This also adds a stub for register_page_bootmem_memmap to allow ppc to build
with sparse vmemmap defined. Leaving this as a stub is fine since the same
vmemmap addresses are also handled in vmemmap_populate and as such are
properly mapped.
Signed-off-by: NNathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
CC: <stable@vger.kernel.org> [v3.9+]

IORESOURCE_BUSY is used to mark temporary driver mem-resources
instead of global regions. This suppresses warnings if regions
overlap with a region marked as BUSY.

This was always the case for VESA/VGA/EFI framebuffer regions so
do the same for simplefb regions. The reason we do this is to
allow device handover to real GPU drivers like
i915/radeon/nouveau which get the same regions via PCI BARs.

Maybe at some point we will be able to unregister platform
devices properly during the handover. In this case the simplefb
region would get removed before the new region is created.
However, this is currently not the case and would require rather
huge changes in remove_conflicting_framebuffers(). Add the BUSY
marker now and try to eventually rewrite the handover for a next release.

Also see kernel/resource.c for more information:

  /*
   * if a resource is "BUSY", it's not a hardware resource
   * but a driver mapping of such a resource; we don't want
   * to warn for those; some drivers legitimately map only
   * partial hardware resources. (example: vesafb)
   */

This suppresses warnings like:

  ------------[ cut here ]------------
  WARNING: CPU: 2 PID: 199 at arch/x86/mm/ioremap.c:171 __ioremap_caller+0x2e3/0x390()
  Info: mapping multiple BARs. Your kernel is fine.
  Call Trace:
    dump_stack+0x54/0x8d
    warn_slowpath_common+0x7d/0xa0
    warn_slowpath_fmt+0x4c/0x50
    iomem_map_sanity_check+0xac/0xe0
    __ioremap_caller+0x2e3/0x390
    ioremap_wc+0x32/0x40
    i915_driver_load+0x670/0xf50 [i915]
    ...
Reported-by: NTom Gundersen <teg@jklm.no>
Tested-by: NTom Gundersen <teg@jklm.no>
Tested-by: NPavel Roskin <proski@gnu.org>
Signed-off-by: NDavid Herrmann <dh.herrmann@gmail.com>
Link: http://lkml.kernel.org/r/1380724864-1757-1-git-send-email-dh.herrmann@gmail.comSigned-off-by: NIngo Molnar <mingo@kernel.org>

Previously, when a signal was registered with SA_SIGINFO, parameters 2
and 3 of the signal handler were written to registers r1 and r2 before
the register set was saved. This led to corruption of these two
registers after returning from the signal handler (the wrong values were
restored).
With this patch, registers are now saved before any parameters are
passed, thus maintaining the processor state from before signal entry.
Signed-off-by: NChristian Ruppert <christian.ruppert@abilis.com>
Signed-off-by: NVineet Gupta <vgupta@synopsys.com>

Turn on SDHCI for i.MX support so machines can boot with local rootfs
on SD. Tested on a Wandboard Quad.
Signed-off-by: NOlof Johansson <olof@lixom.net>
Reviewed-by: NFabio Estevam <fabio.estevam@freescale.com>

Commit ebd97be6 ('PCI: remove ARCH_SUPPORTS_MSI kconfig option')
removes the ARCH_SUPPORTS_MSI Kconfig option that allowed
architectures to indicate whether they support PCI MSI or not. Now,
PCI MSI support can be compiled in on any architecture thanks to the
use of weak functions thanks to 4287d824 ('PCI: use weak functions
for MSI arch-specific functions').

So, architecture specific code is now responsible to ensure that its
PCI MSI code builds in all cases, or be appropriately conditionally
compiled.

On Sparc, the MSI support is only provided for Sparc64, so the
ARCH_SUPPORTS_MSI kconfig option was only selected for SPARC64, and
not for the Sparc architecture as a whole. Therefore, removing
ARCH_SUPPORTS_MSI broke Sparc32 configurations with CONFIG_PCI_MSI=y,
because the Sparc-specific MSI code is not designed to be built on
Sparc32.

To solve this, this commit ensures that the Sparc MSI code is only
built on Sparc64. This is done thanks to a new Kconfig Makefile helper
option SPARC64_PCI_MSI, modeled after the existing SPARC64_PCI. The
SPARC64_PCI_MSI option is an hidden option that is true when both
Sparc64 PCI support is enabled and MSI is enabled. The
arch/sparc/kernel/pci_msi.c file is now only built when
SPARC64_PCI_MSI is true.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reported-by: NGuenter Roeck <linux@roeck-us.net>
Tested-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch proposes to remove the IRQF_DISABLED flag from sparc architecture
code. It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: NMichael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The length argument to strlcpy was still wrong. It could overflow the end of
full_boot_str by 5 bytes. Instead of strcat and strlcpy, just use snprint.
Reported-by: NBrad Spengler <spender@grsecurity.net>
Signed-off-by: NKees Cook <keescook@chromium.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This config item already exists generically in lib/Kconfig.debug.
Remove the duplicate config in arm64.
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

[    1.904000] BUG: scheduling while atomic: swapper/1/0x00000002
[    1.908000] Modules linked in:
[    1.916000] CPU: 0 PID: 1 Comm: swapper Not tainted 3.12.0-rc2-lemote-los.git-5318619-dirty #1
[    1.920000] Stack : 0000000031aac000 ffffffff810d0000 0000000000000052 ffffffff802730a4
          0000000000000000 0000000000000001 ffffffff810cdf90 ffffffff810d0000
          ffffffff8068b968 ffffffff806f5537 ffffffff810cdf90 980000009f0782e8
          0000000000000001 ffffffff80720000 ffffffff806b0000 980000009f078000
          980000009f290000 ffffffff805f312c 980000009f05b5d8 ffffffff80233518
          980000009f05b5e8 ffffffff80274b7c 980000009f078000 ffffffff8068b968
          0000000000000000 0000000000000000 0000000000000000 0000000000000000
          0000000000000000 980000009f05b520 0000000000000000 ffffffff805f2f6c
          0000000000000000 ffffffff80700000 ffffffff80700000 ffffffff806fc758
          ffffffff80700000 ffffffff8020be98 ffffffff806fceb0 ffffffff805f2f6c
          ...
[    2.028000] Call Trace:
[    2.032000] [<ffffffff8020be98>] show_stack+0x80/0x98
[    2.036000] [<ffffffff805f2f6c>] __schedule_bug+0x44/0x6c
[    2.040000] [<ffffffff805fac58>] __schedule+0x518/0x5b0
[    2.044000] [<ffffffff805f8a58>] schedule_timeout+0x128/0x1f0
[    2.048000] [<ffffffff80240314>] msleep+0x3c/0x60
[    2.052000] [<ffffffff80495400>] do_probe+0x238/0x3a8
[    2.056000] [<ffffffff804958b0>] ide_probe_port+0x340/0x7e8
[    2.060000] [<ffffffff80496028>] ide_host_register+0x2d0/0x7a8
[    2.064000] [<ffffffff8049c65c>] ide_pci_init_two+0x4e4/0x790
[    2.068000] [<ffffffff8049f9b8>] amd74xx_probe+0x148/0x2c8
[    2.072000] [<ffffffff803f571c>] pci_device_probe+0xc4/0x130
[    2.076000] [<ffffffff80478f60>] driver_probe_device+0x98/0x270
[    2.080000] [<ffffffff80479298>] __driver_attach+0xe0/0xe8
[    2.084000] [<ffffffff80476ab0>] bus_for_each_dev+0x78/0xe0
[    2.088000] [<ffffffff80478468>] bus_add_driver+0x230/0x310
[    2.092000] [<ffffffff80479b44>] driver_register+0x84/0x158
[    2.096000] [<ffffffff80200504>] do_one_initcall+0x104/0x160
Signed-off-by: NYoichi Yuasa <yuasa@linux-mips.org>
Reported-by: NAaro Koskinen <aaro.koskinen@iki.fi>
Tested-by: NAaro Koskinen <aaro.koskinen@iki.fi>
Cc: linux-mips@linux-mips.org
Cc: Linux Kernel Mailing List <linux-kernel@vger.kernel.org>
Patchwork: https://patchwork.linux-mips.org/patch/5941/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

On my MacBook Air lfb_size is 4M, which makes the bitshit
overflow (to 256GB - larger than 32 bits), meaning we fall
back to efifb unnecessarily.

Cast to u64 to avoid the overflow.
Signed-off-by: NTom Gundersen <teg@jklm.no>
Reviewed-by: NDavid Herrmann <dh.herrmann@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Link: http://lkml.kernel.org/r/1380644320-1026-1-git-send-email-teg@jklm.noSigned-off-by: NIngo Molnar <mingo@kernel.org>

When 5e12a613 and 0cd3754a were introduced, Netgear ReadyNAS 102 .dts
file was queued for inclusion and missed the update to have Mbus (and
then BootROM) ranges properties declared. It also missed the relocation
of Armada 370/XP PCIe DT nodes introduced by 14fd8ed0 after de1af8d4.
This patch fixes that which makes 3.12-rc3 bootable on the NAS.
Signed-off-by: NArnaud Ebalard <arno@natisbad.org>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

The FAULT_FLAG_WRITE flag has been set based on uninitialized variable.

Fixes a regression added by commit 759496ba ("arch: mm: pass
userspace fault flag to generic fault handler")
Signed-off-by: NFelipe Pena <felipensp@gmail.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Like we are doing on DDR0 we need to cleanly shutdown DDR1 if it is
used before rebooting.
If DDR1 is not initialized, we check it and avoid dereferencing its address.
Even by adding two more instructions, we are able to complete the procedure
within a single cache line.
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

HWMOD removal for MMC is breaking edma_start as the events are being manually
triggered due to unused channel list not being clear.

The above issue is fixed by reading the "dmas" property from the DT node if it
exists and clearing the bits in the unused channel list if the dma controller
used by any device is EDMA. For this purpose we use the of_* helpers to parse
the arguments in the dmas phandle list.

Also introduced is a minor clean up of a checkpatch error in old code.
Reviewed-by: NSekhar Nori <nsekhar@ti.com>
Reported-by: NBalaji T K <balajitk@ti.com>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Olof Johansson <olof@lixom.net>
Cc: Nishanth Menon <nm@ti.com>
Cc: Pantel Antoniou <panto@antoniou-consulting.com>
Cc: Jason Kridner <jkridner@beagleboard.org>
Cc: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: NJoel Fernandes <joelf@ti.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

On the TC2 testchip, when all CPUs in a cluster enter standbywfi
and commit a power down request, the power controller will wait
for standbywfil2 coming from L2 cache controller to shut the
cluster down.
By the time all CPUs in a cluster commit a power down request
and enter wfi, the power controller cannot backtrack, or put it
another way, a CPU must not be allowed to complete execution
independently of the power controller, the only way for it to
resume properly must be upon wake-up IRQ pending and subsequent
reset triggered from the power controller.

Current MCPM back-end for TC2 disables the GIC CPU IF only when
power down is committed through the tc2_pm_suspend() method, that
makes sense since a suspended CPU is still online and can receive
interrupts whereas a hotplugged CPU, since it is offline,
migrated all IRQs and shutdown the per-CPU peripherals, hence
their PPIs.

The flaw with this reasoning is the following. If all CPUs in
a clusters are entering a power down state either through CPU
idle or CPU hotplug, when the last man successfully completes
the MCPM power down sequence (and executes wfi), power controller
waits for L2 wfi signal to quiesce the cluster and shut it down.
If, when all CPUs are sitting in wfi, an online CPU hotplugs back
in one of the CPUs in the cluster being shutdown, that CPU
receives an IPI that causes wfi to complete (since tc2_pm_down()
method does not disable the GIC CPU IF in that case - CPU being
hotplugged out, not idle) and the power controller will never see
the stanbywfil2 signal coming from L2 that is required for
shutdown to happen and the system deadlocks.

Further to this issue, kexec hotplugs secondary CPUs out during
kernel reload/restart.
Because kexec may (deliberately) trash the old kernel text, it is
not OK for CPUs to follow the MCPM soft reboot path, since
instructions after the WFI may have been replaced by kexec.

If tc2_pm_down() does not disable the GIC cpu interface, there is a
race between CPU powerdown in the old kernel and the IPI from the
new kernel that triggers secondary boot, particularly if the
powerdown is slow (due to L2 cache cleaning for example).  If the
new kernel wins the race, the affected CPU(s) will not really be
reset and may execute garbage after the WFI.

The only solution to this problem consists in disabling the GIC
CPU IF on a CPU committed to power down regardless of the power
down entry method (CPU hotplug or CPU idle). This way, CPU wake-up
is under power controller control, which prevents unexpected wfi
exit caused by a pending IRQ.

This patch moves the GIC CPU IF disable call in the TC2 MCPM
implementation from the tc2_pm_suspend() method to the
tc2_pm_down() method to fix the mentioned race condition(s).
Reviewed-by: NDave Martin <Dave.Martin@arm.com>
Tested-by: Dave Martin <Dave.Martin@arm.com> (for kexec)
Signed-off-by: NSudeep KarkadaNagesha <sudeep.karkadanagesha@arm.com>
Signed-off-by: NLorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: NNicolas Pitre <nico@linaro.org>
Signed-off-by: NOlof Johansson <olof@lixom.net>

the current dts is lacking interrupt and dma prop for video input
processor of prima2 and atlas6, this patch fixes it.
Signed-off-by: NRenwei Wu <Renwei.Wu@csr.com>
Signed-off-by: NBarry Song <Baohua.Song@csr.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

we lost an address range <0x56000000 0x56000000 0x1b00000> for peri-iobg
of prima2.
Signed-off-by: NBarry Song <Baohua.Song@csr.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Makefile missed to include atlas6-evb.dtb for ARCH_ATLAS6.
Signed-off-by: NBarry Song <Baohua.Song@csr.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

sirf uart and usp-based uart driver with full dma support has
hit 3.12, here we fix the fifosize, dma channels for some HW
prop.
Signed-off-by: NQipan Li <Qipan.Li@csr.com>
Signed-off-by: NBarry Song <Baohua.Song@csr.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Currently, development on arm64 is aided by a Foundation_v8 emulator
distributed by ARM [1]. To run their kernels, users will execute:

  $ ./Foundation_v8 --image linux-system.axf --block-device raring-rootfs

To mount the raring-rootfs filesystem, the kernel parameter should
typically include:

  root=/dev/vda

For this device to be present, the kernel must be compiled with
VIRTIO_{MMIO,BLK}. To make this work out-of-the-box, make it part of the
default configuration.

[1]: https://silver.arm.com/browse/FM00A

Cc: Will Deacon <will.deacon@arm.com>
Cc: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: NRamkumar Ramachandra <artagnon@gmail.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

Most readily available root filesystems are formatted as EXT4 these
days. For example, see the raring rootfs that the Debian folk is
preparing [1].

[1]: http://people.debian.org/~wookey/bootstrap/rootfs/

Cc: Will Deacon <will.deacon@arm.com>
Cc: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: NRamkumar Ramachandra <artagnon@gmail.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

Without that fix, at the end of the shutdown process, the board is
still powered (led glowing, fan running, ...).
Signed-off-by: NArnaud Ebalard <arno@natisbad.org>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

NETGEAR ReadyNAS 102 Power button definition in .dts file flags
associated GPIO active low instead of active high. This results
in reversed events reported by input subsystem (0 returned when
the button is pressed, 1 when released). This patch makes
associated GPIO active high to recover correct behaviour.
Signed-off-by: NArnaud Ebalard <arno@natisbad.org>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

__initdata tag should be placed between the variable name and equal
sign for the variable to be placed in the intended .init.data section.
Signed-off-by: NBartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/5934/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The patch fixes the following compiler warning:
    CC      arch/avr32/kernel/process.o
  arch/avr32/kernel/process.c: In function 'copy_thread':
  arch/avr32/kernel/process.c:292: warning: assignment makes integer \
  from pointer without a cast
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Acked-by: NHans-Christian Egtvedt <egtvedt@samfundet.no>

Since commit 01426478
(avr32: Use generic idle loop) the kernel throws the
following warning on avr32:

  WARNING: at 900322e4 [verbose debug info unavailable]
  Modules linked in:
  CPU: 0 PID: 0 Comm: swapper Not tainted 3.12.0-rc2 #117
  task: 901c3ecc ti: 901c0000 task.ti: 901c0000
  PC is at cpu_idle_poll_ctrl+0x1c/0x38
  LR is at comparator_mode+0x3e/0x40
  pc : [<900322e4>]    lr : [<90014882>]    Not tainted
  sp : 901c1f74  r12: 00000000  r11: 901c74a0
  r10: 901d2510  r9 : 00000001  r8 : 901db4de
  r7 : 901c74a0  r6 : 00000001  r5 : 00410020  r4 : 901db574
  r3 : 00410024  r2 : 90206fe0  r1 : 00000000  r0 : 007f0000
  Flags: qvnzc
  Mode bits: hjmde....G
  CPU Mode: Supervisor
  Call trace:
   [<90039ede>] clockevents_set_mode+0x16/0x2e
   [<90039f00>] clockevents_shutdown+0xa/0x1e
   [<9003a078>] clockevents_exchange_device+0x58/0x70
   [<9003a78c>] tick_check_new_device+0x38/0x54
   [<9003a1a2>] clockevents_register_device+0x32/0x90
   [<900035c4>] time_init+0xa8/0x108
   [<90000520>] start_kernel+0x128/0x23c

When the 'avr32_comparator' clockevent device is registered,
the clockevent core sets the mode of that clockevent device
to CLOCK_EVT_MODE_SHUTDOWN. Due to this, the 'comparator_mode'
function calls the 'cpu_idle_poll_ctrl' to disables idle poll.
This results in the aforementioned warning because the polling
is not enabled yet.

Change the code to only disable idle poll if it is enabled by
the same function to avoid the warning.

Cc: stable@vger.kernel.org
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Acked-by: NHans-Christian Egtvedt <egtvedt@samfundet.no>

Use kbuild to add asm-generic headers that do nothing, also remove the arch
specific wrapper headers.

This only affects headers that do nothing but include the generic
equivalent. It does not touch any header that does a little more.
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>
Signed-off-by: NHans-Christian Egtvedt <egtvedt@samfundet.no>

Ran into this cryptic PMU bootup log recently:

[    0.124047] Performance Events:
[    0.125000] smpboot: ...

Turns out we print this if no PMU is detected. Fall back to
the right condition so that the following is printed:

[    0.122381] Performance Events: no PMU driver, software events only.

Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Link: http://lkml.kernel.org/n/tip-u2fwaUffakjp0qkpRfqljgsn@git.kernel.orgSigned-off-by: NIngo Molnar <mingo@kernel.org>