Create a new device tree file for the Broadcom Northstar Plus
bcm958622hr SVK.  This SVK has 2GB RAM, 5 port Ethernet, 2 PCI slots,
and 1 UART.  Also, it has the ability to reboot via GPIO.  To be added
in the future are support for the USB and SLIC audio.
Signed-off-by: NJon Mason <jon.mason@broadcom.com>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>

Create a new device tree file for the Broadcom Northstar Plus
bcm958623hr SVK.  This SVK has 2GB RAM, 5 ports Ethernet, SATA, 2 PCI
slots, and 1 UART.  Also, it has the ability to reboot via GPIO.  To be
added in the future are support for the USB and SLIC audio.
Signed-off-by: NJon Mason <jon.mason@broadcom.com>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>

Create a new device tree file for the Broadcom Northstar Plus
bcm988312hr SVK.  This SVK has 2GB RAM, 5 ports Ethernet, 2 eSATA, 2 PCI
slots, and 1 UART.  Also, it has the ability to reboot via GPIO.  To be
added in the future is support for the USB.
Signed-off-by: NJon Mason <jon.mason@broadcom.com>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>

Create a new device tree file for the Broadcom Northstar Plus
bcm958522er SVK.  This SVK has 2GB RAM, 2 ports Ethernet, 2 PCI slots,
and 1 UART.  Also, it has the ability to reboot via GPIO.  To be added
in the future is support for the USB.
Signed-off-by: NJon Mason <jon.mason@broadcom.com>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>

Create a new device tree file for the Broadcom Northstar Plus
bcm958525er SVK.  This SVK has 2GB RAM, 2 ports Ethernet, 2 eSATA, 2 PCI
slots, and 1 UART.  Also, it has the ability to reboot via GPIO.  To be
added in the future is support for the USB.
Signed-off-by: NJon Mason <jon.mason@broadcom.com>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>

Add the ability to reboot the bcm958625xmc board via GPIO.
Unfortunately, not all of the NSP based boards use the same GPIO pin
and one doesn't have the ability to reboot via GPIO at all.  So, this
will need to be specified per DTS file.
Signed-off-by: NJon Mason <jon.mason@broadcom.com>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>

Add the ability to reboot the bcm958625hr board via GPIO.
Unfortunately, not all of the NSP based boards use the same GPIO pin and
one doesn't have the ability to reboot via GPIO at all.  So, this will
need to be specified per DTS file.
Signed-off-by: NJon Mason <jon.mason@broadcom.com>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>

Add 1GB of memory starting at physical offset 0x6000_0000.
Signed-off-by: NJon Mason <jon.mason@broadcom.com>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>

Add 2GB of memory starting at physical offset 0x6000_0000.
Signed-off-by: NJon Mason <jon.mason@broadcom.com>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>

Enable SATA on bcm958625xmc and add the i2c devices present.
Signed-off-by: NJon Mason <jon.mason@broadcom.com>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>

Add SATA support to bcm958625hr DTS
Signed-off-by: NJon Mason <jon.mason@broadcom.com>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>

The BCM958625HR board has 2GB of RAM available.  Increase the amount
from 512MB to 2GB and add the device type to the memory entry.

Fixes: 9a4865d4 ("ARM: dts: NSP: Specify RAM amount for BCM958625HR board")
Signed-off-by: NJon Mason <jon.mason@broadcom.com>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>

Add PWM support to the device tree for the Broadcom Northstar Plus SoC.
Signed-off-by: NYendapally Reddy Dhananjaya Reddy <yendapally.reddy@broadcom.com>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>

Driver for Northstar USB 2.0 PHY was added in 4.7-rc1 by:
commit d3feb406 ("phy: bcm-ns-usb2: new driver for USB 2.0 PHY on
Northstar").
It should be used to let EHCI platform driver init PHY.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>

Add the layout of the switch ports found on the BCM958625HR reference
board. The CPU port is hooked up to the AMAC0 Ethernet controlelr
adapter, so we also enable it.
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>

Add the Switch Register Access Block node, this peripheral is identical
to the BCM5301x Northstar SoC, but we utilize the SoC-wide
"brcm,nsp-srab" compatible string to illustrate the integration
difference here.
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>

Add Device Tree entries for the Ethernet devices (AMAC) present on the Broadcom
Northstar Plus SoCs.
Signed-off-by: NJon Mason <jon.mason@broadcom.com>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>

This commit adds definition for cpu_on, cpu_off and cpu_suspend
commands.  These definitions must match the corresponding PSCI
definitions in boot monitor.

Having those command and corresponding PSCI support in boot monitor
allows run time CPU hot plugin.

Link: http://lkml.kernel.org/r/E1b8koV-0004Hf-2j@rmk-PC.armlinux.org.ukSigned-off-by: NKeerthy <j-keerthy@ti.com>
Signed-off-by: NVitaly Andrianov <vitalya@ti.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Cc: Pratyush Anand <panand@redhat.com>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: Baoquan He <bhe@redhat.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Simon Horman <horms@verge.net.au>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Replace the non-standard vendor prefix stm with st for
STMicroelectronics. The drivers do not specify the vendor prefixes
since the I2C Core strips them away from the DT provided compatible
string. Therefore, changing existing device trees does not have any
impact on device detection.
Signed-off-by: NStefan Agner <stefan@agner.ch>
Signed-off-by: NRob Herring <robh@kernel.org>

The inet86dz board is a board used in 7" tablets from various oems.

These tablets are a23 based 7" tablets featuring a 1024x600 LCD,
512MB RAM, 4G NAND, rtl8188etv usb wifi, gsl1680 touchschreen,
micro-sd slot, 3.5mm headphone jack and a micro-usb otg connector
which doubles as charging port.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The Polaroid MID2407PXE03 is an a23 based 7" tablet based on a M86_MB V2.0
PCB, featuring a 800x480 LCD, 512MB RAM, 4G NAND, esp8089 wifi, gsl1680
touchschreen, micro-sd slot, 3.5mm headphone jack and a micro-usb otg
connector which doubles as charging port.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

This results in quite a nice cleanup for this dts file.

As an added bonus this also enables backlight, regulator and full otg
support. I've tested that all these works as advertised.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

This results in quite a nice cleanup for this dts file.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Add a drivevbus-supply property so that the drivevbus regulator
reports the right voltage value.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Copy sun8i-q8-common.dtsi to sun8i-reference-design-tablet.dtsi. This
is part of renaming all the sun?i-q8-common.dtsi files to
sun?i-reference-design-tablet.dtsi since most of the hw-config in there
is shared by all sunxi tablets.

Note that in this case we keep sun5i-q8-common.dtsi as it is shared
between a23 / a33 q8 tablets. Also we leave the usb-wifi config in
there (rather then in sun8i-reference-design-tablet.dtsi) as most
sun8i tablets use sdio wifi rather then usb wifi.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

This results in a nice cleanup for this dts file.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

This results in quite a nice cleanup for this dts file.

Note as a side-effect this also enables the on board speaker / headphones
out. I've tested that this works as advertised.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Remove all mention of q8 from sun5i-reference-design-tablet.dtsi.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Set lradc vref to the actual avcc ldo, rather then to the fixed 3v0
regulator from common-regulators.dtsi.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Rename sun5i-q8-common.dtsi to sun5i-reference-design-tablet.dtsi. This
is part of renaming all the sun?i-q8-common.dtsi files to
sun?i-reference-design-tablet.dtsi since most of the hw-config in there
is shared by all sunxi tablets.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

This is a preparation patch for renaming sun5i-q8-common.dtsi to
sun5i-reference-design-tablet.dtsi and sharing it between all
the A13 tablet dts files.

Since we only have a panel config for the 18 tablets (for now) move
this to the q8 specific dts file.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Rename sunxi-q8-common.dtsi to sunxi-reference-design-tablet.dtsi. This
is part of renaming all the sun?i-q8-common.dtsi files to
sun?i-reference-design-tablet.dtsi since most of the hw-config in there
is shared by all sunxi tablets.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Commit 0dfd582e ("watchdog: qcom: use timer devicetree
binding") moved to use the watchdog as a subset timer
register block. Some devices have the watchdog completely
standalone with slightly different register offsets as
well so let's account for the differences here.

The existing "kpss-standalone" compatible string doesn't
make it entirely clear exactly what the device is so
rename to "kpss-wdt" to reflect watchdog timer
functionality. Also update ipq4019 DTS with an SoC
specific compatible.
Signed-off-by: NMatthew McClintock <mmcclint@codeaurora.org>
Signed-off-by: NThomas Pedersen <twp@codeaurora.org>
Reviewed-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

Update the compatible string to align with driver and also
add SoC specific string to DTS.

CC: linux-watchdog@vger.kernel.org
Signed-off-by: NMatthew McClintock <mmcclint@codeaurora.org>
Signed-off-by: NThomas Pedersen <twp@codeaurora.org>
Reviewed-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

Building both ARMv4 and ARMv5 dtbs when SOC_SAM_V4_V5 is an issue for
kernelci because it will then attempt to boot ARMv4 kernels on at91sam9
which doesn't work.

Use CONFIG_SOC_AT91RM9200 and CONFIG_SOC_AT91SAM9 instead.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

Separate the definitions for the emac and the gmac in different files and
include them in the final board dts that uses them.

Solves:
Warning (unit_address_vs_reg): Node /ahb/apb/ethernet@f0028000 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /ahb/apb/ethernet@f802c000 has a unit name, but no reg property
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

Add a reg property in the endpoint node as documented in
Documentation/devicetree/bindings/media/video-interfaces.txt

Solves:
Warning (unit_address_vs_reg): Node /ahb/apb/isi@f8048000/port/endpoint@0 has a unit name, but no reg property
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

The ISI is only present on the at91sam9g25, move the definition to the
at91sam9g25ek board dts to avoid warnings.

Solves the following warning for other 9x5ek boards:
Warning (unit_address_vs_reg): Node /ahb/apb/isi@f8048000 has a unit name, but no reg property
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

i2c-gpio doesn't need a reg property. Change the node names to i2c-gpio-x
as used in other dts to remove the unit-address.

Solves:
Warning (unit_address_vs_reg): Node /i2c@0 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /i2c@1 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /i2c@2 has a unit name, but no reg property
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

vcc_3v3_reg is a fixed regulator and doesn't need a reg property. Remove
its unit-address.

Solves:
Warning (unit_address_vs_reg): Node /fixedregulator@0 has a unit name, but no reg property
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>