SDIO reset was not happening properly on mwifiex as cancel_work_sync
in mwifiex_sdio_remove used to kill the calling work function itself.
Due to this, the interface was not getting removed and card was not
getting added again. Reset work function has been made independent
of adapter variable and cancel_work_sync has been moved to cleanup
function.
Signed-off-by: NMaithili Hinge <maithili@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Signed-off-by: NOleksij Rempel <linux@rempel-privat.de>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

replace REG_WRITE to REG_RMW and place every thing in one
RMW buffer.
Signed-off-by: NOleksij Rempel <linux@rempel-privat.de>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

it is possible to reduce time needed for this function
by rplacing REG_WRITE with REG_RMW (plus dummy 0) and putt all commands
in same buffer.
Signed-off-by: NOleksij Rempel <linux@rempel-privat.de>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

it will reduce exution time from 14ms to 2ms on ar9271
Signed-off-by: NOleksij Rempel <linux@rempel-privat.de>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

use REG_RMW in ath9k_hw_analog_shift_rmw.
It will double execution speed on usb bus.
Signed-off-by: NOleksij Rempel <linux@rempel-privat.de>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Signed-off-by: NOleksij Rempel <linux@rempel-privat.de>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Signed-off-by: NOleksij Rempel <linux@rempel-privat.de>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Signed-off-by: NOleksij Rempel <linux@rempel-privat.de>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Signed-off-by: NOleksij Rempel <linux@rempel-privat.de>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Signed-off-by: NOleksij Rempel <linux@rempel-privat.de>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

this will reduce some overhead on usb bus.
Signed-off-by: NOleksij Rempel <linux@rempel-privat.de>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

insted of reading each register separatly
and waste 4ms on each operation, we can
use one shot read.
Signed-off-by: NOleksij Rempel <linux@rempel-privat.de>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

REG_READ generate most overhead on usb bus. It send and read micro packages
and reduce usb bandwidth. To reduce this overhead we should read in batches.
Signed-off-by: NOleksij Rempel <linux@rempel-privat.de>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Signed-off-by: NOleksij Rempel <linux@rempel-privat.de>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Signed-off-by: NOleksij Rempel <linux@rempel-privat.de>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Signed-off-by: NOleksij Rempel <linux@rempel-privat.de>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This function uses mixed styles for register names/numbers which
is make harder reading and optimisation.
Signed-off-by: NOleksij Rempel <linux@rempel-privat.de>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Since usb bus add extra delay on each request, a command
with read + write requests is too expensive. We can dramtically
reduce usb load by moving this command to firmware.

In my tests, this patch will reduce channel scan time
for about 5-10 seconds.
Signed-off-by: NOleksij Rempel <linux@rempel-privat.de>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

I changed REG_CR+2 and (MSR) to MSR because MSR is defined as (REG_CR + 2).
Signed-off-by: NTaehee Yoo <ap420073@gmail.com>
Acked-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Seems H/W report correctly firmware Autorun value only at initialization
stage. When we close interface and open it again, Autorun value is 0 and
we try to load firmware what kills the device. To fix clear
REQUIRE_FIRMWARE firmware flag, to do not load firmware again, once we
discover Autorun mode.
Reported-and-tested-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

AIC needs to be registered only when BTCOEX is enabled.
This fixes the error reported by kbuild:

>> ERROR: "ar9003_hw_attach_aic_ops" [drivers/net/wireless/ath/ath9k/ath9k_hw.ko] undefined!
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Some BCM47XX SoC routers have LEDs connected to extra PCIe bcma buses.
Handling them in arch code requires predictable GPIO numbers.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

With patch '960d6d08 "mwifiex: delay skb allocation for RX
until cmd53 over"' we no more pass skb parameter to MP aggregation setup
helper function. We instead pass length to be aggregated.

This patch fixes an issue where we were passing length parameter of NULL
skb to aggregation routine resulting into crash. We should instead pass
rx_len received from mp_regs.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

There are no known BCM4354 PCIe devices released so removing
support from the driver until proven otherwise.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Recently support was added for the BCM4345 SDIO chipset by
commit 9c510265 ("brcmfmac: Add support for BCM4345 SDIO chipset")
however this was verified using a BCM43455 device, which is
a more recent revision of the chip. This patch assure that
older revisions are not probed as they would fail.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NSyed Asifful Dayyan <syedd@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch added support for the BCM43430 802.11n SDIO chipset.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NDaniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The BCM4356 PCIe wireless device was added recently but overlooked
the fact that the MODULE_FIRMWARE() macros were missing for the
firmwares needed by this device.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

SDIO uses a thread to handle all communication with the device,
for this data is exchanged between threads. This data needs proper
memory barriers to make sure that data "exchange" is going correct.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NDaniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Several host controllers supporting runtime-pm are causing issues
with our sdio wireless cards because they disable the sdio interrupt
upon going into runtime suspend. This patch avoids that by doing
a pm_runtime_forbid() call during the probe. Tested with Sony Vaio
Duo 13 which uses sdhci-acpi host controller.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

It's clear from the indenting that curly braces were intended here.

Fixes: e35000ea ('mwifiex: preprocess packets from TX queue')
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Add the USB Id to link the D-Link DWA 130 USB Wifi adapter
to the rt2830 driver.
Signed-off-by: NScott Branden <sbranden@broadcom.com>
Signed-off-by: NPieter Truter <ptruter@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Multicast is not yet properly supported for all connection types;
actually, only non-secure AP is supported. For all other cases,
fall back to old "pseudo-DMS" approach. Namely, for:
- PBSS
- secure connection

When re-routing MCAST Rx->Tx on the AP, do not Tx back to the origin
of the frame
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Use dedicated vring for multicast frames; this vring allocated for
AP and PBSS (both P2P GO and client) configurations

For short frames, use MCS0; for long - MCS1
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Sync with the wmi definitions from the firmware team
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Fix checkpatch warning:
WARNING: Prefer ether_addr_copy() over memcpy() if the
Ethernet addresses are __aligned(2)
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

For the networking code and for hardware network accelerators,
it is better to have IP header 4*n aligned. On the other side,
DMA on Rx path require buffer to be aligned on 4*n as well.
Having 14 bytes of Ethernet header, these 2 alignment
requests are in contradiction.

To solve this, order hardware offload block to not remove
SNAP header. This adds extra 6 bytes between addresses and
ethertype, making it 20 bytes total. This way, both buffer and
IP header are 4*n aligned. Remaining is only to remove SNAP
by shifting addresses 6 bytes. This involves data copying, so
this feature should be disabled unless required by the platform.

Module parameter "rx_align_2" (bool, default - false)
introduced to control this feature. Feature is completely disabled
when parameter is false.
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

"echo" used to be called when no firmware loaded to the NIC,
this causes error output.

Probe firmware with "echo" only after it returned "ready" event.
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>