#elif CONFIG_44x
in ibm4xx.h should've been
 #elif defined(CONFIG_44x)
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

indirect chains of includes are arch-specific and can't
be relied upon...  (hell, even attempt to build it for
itanic would trigger vmalloc.h ones; err.h triggers
on e.g. alpha).
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The crypto_hash_update call in hmac_init gave the number 1
instead of the length of the sg list in bytes.  This is a
missed conversion from the digest => hash change.

As tcrypt only tests crypto_hash_digest it didn't catch this.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
  [CIFS] statfs for cifs unix extensions no longer experimental
  [CIFS] New POSIX locking code not setting rc properly to zero on successful
  [CIFS] Support deep tree mounts (e.g. mounts to //server/share/path)

* master.kernel.org:/pub/scm/linux/kernel/git/davej/agpgart:
  [AGPGART] Rework AGPv3 modesetting fallback.
  [AGPGART] Add suspend callback for i965
  [AGPGART] Fix number of aperture sizes in 830 gart structs.
  [AGPGART] Intel 965 Express support.
  [AGPGART] agp.h: constify struct agp_bridge_data::version
  [AGPGART] const'ify VIA AGP PCI table.
  [AGPGART] CONFIG_PM=n slim: drivers/char/agp/intel-agp.c
  [AGPGART] CONFIG_PM=n slim: drivers/char/agp/efficeon-agp.c
  [AGPGART] Const'ify the agpgart driver version.
  [AGPGART] remove private page protection map

* master.kernel.org:/pub/scm/linux/kernel/git/davej/cpufreq:
  [CPUFREQ] sw_any_bug_dmi_table can be used on resume, so it isn't initdata
  [CPUFREQ] Fix some more CPU hotplug locking.
  [CPUFREQ] Workaround for BIOS bug in software coordination of frequency
  [CPUFREQ] Longhaul - Add voltage scaling to driver
  [CPUFREQ] Fix sparse warning in ondemand
  [CPUFREQ] make drivers/cpufreq/cpufreq_ondemand.c:powersave_bias_target() static
  [CPUFREQ] Longhaul - Add ignore_latency option
  [CPUFREQ] Longhaul - Disable arbiter
  [CPUFREQ][2/2] ondemand: updated add powersave_bias tunable
  [CPUFREQ][1/2] ondemand: updated tune for hardware coordination
  [CPUFREQ] Fix typo.

missing le16_to_cpu()
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

In

|Author: James Simmons <jsimmons@kozmo.(none)>
|Date:   Thu Mar 13 22:37:08 2003 -0800
|
|    [FBCON] Cursor handling clean up. I nuked several static variables.

we have

-static void fbcon_vbl_handler(int irq, void *dummy, struct pt_regs *fp)
+static void fb_vbl_handler(int irq, void *dev_id, struct pt_regs *fp)

and 3 years later a couple of instances missed back then still remains
there.
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

iommu_init() and iounit_init() are never called for sun4, but that's not
enough - these calls should be ifdefed out since the functions in question
simply do not exist for CONFIG_SUN4 kernel.
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

memcpy() from iomem is a bad thing...
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Back when pci_dev had base_address[], loop of form
	base = &...->base_address[0];
	for (.....) {
		...
		*base++ = addr;
	}
was fine, but when that array got spread in ->resource[...].start
replacing the initialization with
	base = &...->resource[0].start;
was not a sufficient modification.  IOW this code got broken for cases
when there had been more than one resource to fill.  All way back in
2.3.41-pre3...
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

several targets have no ....at() family and m32r calls its only chown variant
chown32(), with __NR_chown being undefined.  creat(2) is also absent in some
targets.
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

sw_any_bug_dmi_table can be used on resume, so it isn't initdata.
Signed-off-by: NJeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: NDave Jones <davej@redhat.com>

Lukewarm IQ detected in hotplug locking
BUG: warning at kernel/cpu.c:38/lock_cpu_hotplug()
[<b0134a42>] lock_cpu_hotplug+0x42/0x65
[<b02f8af1>] cpufreq_update_policy+0x25/0xad
[<b0358756>] kprobe_flush_task+0x18/0x40
[<b0355aab>] schedule+0x63f/0x68b
[<b01377c2>] __link_module+0x0/0x1f
[<b0119e7d>] __cond_resched+0x16/0x34
[<b03560bf>] cond_resched+0x26/0x31
[<b0355b0e>] wait_for_completion+0x17/0xb1
[<f965c547>] cpufreq_stat_cpu_callback+0x13/0x20 [cpufreq_stats]
[<f9670074>] cpufreq_stats_init+0x74/0x8b [cpufreq_stats]
[<b0137872>] sys_init_module+0x91/0x174
[<b0102c81>] sysenter_past_esp+0x56/0x79

As there are other places that call cpufreq_update_policy without
the hotplug lock, it seems better to keep the hotplug locking
at the lower level for the time being until this is revamped.
Signed-off-by: NDave Jones <davej@redhat.com>

* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband: (65 commits)
  IB: Fix typo in kerneldoc for ib_set_client_data()
  IPoIB: Add some likely/unlikely annotations in hot path
  IPoIB: Remove unused include of vmalloc.h
  IPoIB: Rejoin all multicast groups after a port event
  IPoIB: Create MCGs with all attributes required by RFC
  IB/sa: fix ib_sa_selector names
  IB/iser: INFINIBAND_ISER depends on INET
  IB/mthca: Simplify calls to mthca_cq_clean()
  RDMA/cma: Document rdma_accept() error handling
  IB/mthca: Recover from catastrophic errors
  RDMA/cma: Document rdma_destroy_id() function
  IB/cm: Do not track remote QPN in timewait state
  IB/sa: Require SA registration
  IPoIB: Refactor completion handling
  IB/iser: Do not use FMR for a single dma entry sg
  IB/iser: fix some debug prints
  IB/iser: make FMR "page size" be 4K and not PAGE_SIZE
  IB/iser: Limit the max size of a scsi command
  IB/iser: fix a check of SG alignment for RDMA
  RDMA/cma: Protect against adding device during destruction
  ...

* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6:
  [netdrvr] mv643xx_eth: fix obvious typo, which caused build breakage
  [netdrvr] lp486e: fix typo

Signed-off-by: NKrishna Kumar <krkumar2@in.ibm.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Signed-off-by: NEli Cohen <eli@dev.mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

IPoIB doesn't use anything from <linux/vmalloc.h>, so don't include it.
Signed-off-by: NDotan Barak <dotanb@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

When ipoib_ib_dev_flush() is called because of a port event, the
driver needs to rejoin all multicast groups, since the flush will call
ipoib_mcast_dev_flush() (via ipoib_ib_dev_down()).  Otherwise no
(non-broadcast) multicast groups will be rejoined until the networking
core calls ->set_multicast_list again, and so multicast reception will
be broken for potentially a long time.
Signed-off-by: NEli Cohen <eli@mellanox.co.il>
Signed-off-by: NMichael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

RFC 4391 ("Transmission of IP over InfiniBand (IPoIB)") says:

  If the IB multicast group does not already exist, one must be
  created first with the IPoIB link MTU.  The MGID MUST use the same
  P_Key, Q_Key, SL, MTU, and HopLimit as those used in the
  broadcast-GID.  The rest of attributes SHOULD follow the values used
  in the broadcast-GID as well.

However, the current IPoIB driver is only setting the attributes
required by the InfiniBand spec to create a multicast group, so in
particular the MTU and HopLimit are not being set.  Add these
attributes when creating MCGs, and also set the Rate attribute, since
IPoIB pays attention to that attribute as well.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Relevant SA queries are actually "greater than" / "less than", not
"greater than or equal" / "less than or equal" as the names imply.
(See IB spec 1.2 Vol 1, 15.2.5.16 PATHRECORD/Table 205 PathRecord)
Signed-off-by: NMichael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

iSER won't build without CONFIG_INET enabled, so make Kconfig reflect that.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

If a QP has separate send and receive CQs, then the send CQ will never
have receive completions from that QP in it.  So when cleaning the
send CQ, there's no need to pass in an SRQ pointer, even if the QP is
attached to an SRQ.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Document the reject sending and modifying QP to error done in rdma_accept().
Signed-off-by: NOr Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: NSean Hefty <sean.hefty@intel.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Trigger device remove and then add when a catastrophic error is
detected in hardware.  This, in turn, will cause a device reset, which
we hope will recover from the catastrophic condition.

Since this might interefere with debugging the root cause, add a
module option to suppress this behaviour.
Signed-off-by: NJack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: NMichael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Clarify that rdma_destroy_id cancels outstanding asynchronous operations on the
Associated id.
Signed-off-by: NOr Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: NSean Hefty <sean.hefty@intel.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Do not track remote QPN in TimeWait state, since QP is not connected.
Signed-off-by: NMichael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Require users to register with SA module, to prevent the sa_query
module text from going away while an SA query callback is still
running.  Update all in-tree users for the new interface.
Signed-off-by: NMichael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: NSean Hefty <sean.hefty@intel.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Split up ipoib_ib_handle_wc() into ipoib_ib_handle_rx_wc() and
ipoib_ib_handle_tx_wc() to make the code easier to read.  This will
also help implement NAPI in the future.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Fast Memory Registration (fmr) is used to register for rdma an sg whose
elements are not linearly sequential after dma mapping.

The IB verbs layer provides an "all dma memory MR (memory region)" which
can be used for RDMA-ing a dma linearly sequential buffer.

Change the code to use the dma mr instead of doing fmr when dma mapping
produces a single dma entry sg.
Signed-off-by: NErez Zilber <erezz@voltaire.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

fix and add some debug prints related to iser
handling of memory for rdma.
Signed-off-by: NErez Zilber <erezz@voltaire.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

As iser is able to use at most one rdma operation for the
execution of a scsi command, and registration of the sg
associated with scsi command has its restrictions, the code
checks if an sg is "aligned for rdma".

Alignment for rdma is measured in "fmr page" units whose
possible resolutions are different between HCAs and can be
smaller, equal or bigger to the system page size.

When the system page size is bigger than 4KB (eg the default
with ia64 kernels) there a bigger chance that an sg would be
aligned for rdma if the fmr page size is 4KB.

Change the code to create FMR whose pages are of size 4KB
and to take that into account when processing the sg.
Signed-off-by: NErez Zilber <erezz@voltaire.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Currently, the data length of a command coming down from scsi-ml
is limited only by the size of its sg list (sg_tablesize). The
max data length may be different for different page size values.
By setting max_sectors, we limit the data length to
max_sectors*512 bytes.
Signed-off-by: NErez Zilber <erezz@voltaire.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

dma mapping may include a "compaction" of the sg associated with scsi command.
Hence, the size of the maximal prefix of the SG which is aligned for rdma must be
compared against the length of the dma mapped sg (mem->dma_nents) and not against
the size of it before it was mapped (mem->size).
Signed-off-by: NErez Zilber <erezz@voltaire.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>