Add sh7724 code to save and restore CPG state during
R-standby. Only CPG registers IRDACLKCR and SPUCLKCR
require software save and restore.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NKuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Add sh7724 code to save and restore RWDT state during
R-standby. Without this patch the watchdog will generate
a reset shortly after resuming from R-standby.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Make use of the recently added notifier chains for sh7724
r-standby register save/restore handling. At this point
only the BSC and INTC are handled.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Convert the processor platform device setup
functions from __initcall() and sometimes
device_initcall() to arch_initcall().

This makes sure that the platform devices are
registered a bit earlier so the devices are
available when drivers register using initcall
levels earlier than device_initcall().

A good example is platform devices needed by
i2c-sh_mobile.c which registers a bit earlier
using subsys_initcall().
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Add hwblk_id to on-chip sh7724 platform devices.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Convert the processor platform device setup
functions from __initcall() and sometimes
device_initcall() to arch_initcall().

This makes sure that the platform devices are
registered a bit earlier so the devices are
available when drivers register using initcall
levels earlier than device_initcall().

A good example is platform devices needed by
i2c-sh_mobile.c which registers a bit earlier
using subsys_initcall().
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NKuninori Morimoto <morimoto.kuninori@renesas.com>
Acked-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch follows Rev 0.50 manual
Signed-off-by: NKuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NKuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch adds TMU platform data for sh7724. Both clockevent
and clocksource support is enabled.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Kill off all of the clk_always_enabled leftovers and use the new flag
directly.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This adds the clock specifier to all of the SH-Mobile sh-sci ports.
Impacted CPUs are SH7343/SH7366/SH7722/SH7723/SH7724.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

All of the SH timers use a roughly identical structure for platform data,
which presently is broken out for each block. Consolidate all of these
definitions, as there is no reason for them to be broken out in the first
place.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Follows the SH7722/SH7723 changes.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

rtc-sh takes care of this now, so no need to have this always enabled.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This enables support for the CMT clockevents driver on SH7724.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This adds uio_pdrv_genirq support for the VEU.
Signed-off-by: NKuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This adds uio_pdrv_genirq support for the VPU.
Signed-off-by: NKuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This adds support for the SH-Mobile I2C controller on the SH7724.
Signed-off-by: NKuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This implements initial support for the SH-Mobile R2R CPU.
Based on Rev 0.11 of the initial SH7724 hardware manual.
Signed-off-by: NKuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>