Signed-off-by: NDean Anderson <dean@sensoray.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

s2255drv fixes for big endian architecture
Signed-off-by: NDean Anderson <dean@sensoray.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch adapts the changes submitted by Dainius Ridzevicius to the
linux-media mailing list on 8/14/09, to the current sources in order
to make the Kworld VS-DVB-T 323UR usb device work.

I also removed the "not validated" flag since I own the device and validated
that it works fine after the patch is applied.

Thanks to Devin Heitmueller for his guidance with the code.
Signed-off-by: NAntonio Larrosa <larrosa@kde.org>
Acked-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Video status capability for inputs on Sensoray 2255 driver.
Signed-off-by: NDean Anderson <dean@sensoray.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Current dvb_demux_tscheck processing doesn't allow to enable check on loaded
module. dvb_demux_tscheck can be enabled only when loading module (
dvb_dmx_init should be called to enable dvb_demux_tscheck ). This patch fix
this issue.
Signed-off-by: NAbylay Ospan <aospan@netup.ru>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NJean-François Moine <moinejf@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NJean-François Moine <moinejf@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Make the range of exposure values (0-0x1770) distribute evenly through
HV7131R's exposure control bytes.
Signed-off-by: NGerman Galkin <galkinga@gmail.com>
Signed-off-by: NJean-François Moine <moinejf@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NJean-François Moine <moinejf@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NErik Andrén <erik.andren@gmail.com>
Signed-off-by: NJean-François Moine <moinejf@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The version number in the CA_PMT message sent to the hardware was
alwaysed set to zero. This could cause problems if the PMT would
change during decryption of a channel since the new CA_PMT would have
the same version number as the old. The version number is now copied
from the original PMT.
Signed-off-by: NHenrik Kurelid <henrik@kurelid.se>
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The condition (msg[i].addr == 0xd0) is checked twice the second one
is not necessary.

This will remove the following compiler warning:
   az6027.c: In function 'az6027_i2c_xfer':
   az6027.c:942: warning: 'index' may be used uninitialized in this function
   az6027.c:943: warning: 'value' may be used uninitialized in this function
   az6027.c:944: warning: 'length' may be used uninitialized in this function
   az6027.c:945: warning: 'req' may be used uninitialized in this function
Signed-off-by: NMárton Németh <nm127@freemail.hu>
Cc: Manu Abraham <abraham.manu@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Make the local variables and functions static. Some of them are not exported by their
symbol name but used trough other means. For example a pointer of the operation
structure is passed through a function call.

This will remove the following sparse warnings (see "make C=1"):
 * pd-video.c:20:5: warning: symbol 'usb_transfer_mode' was not declared. Should it be static?
 * pd-video.c:621:5: warning: symbol 'fire_all_urb' was not declared. Should it be static?
 * pd-video.c:881:5: warning: symbol 'vidioc_s_std' was not declared. Should it be static?
 * pd-video.c:1024:5: warning: symbol 'vidioc_g_audio' was not declared. Should it be static?
 * pd-video.c:1033:5: warning: symbol 'vidioc_s_audio' was not declared. Should it be static?
 * pd-video.c:1193:5: warning: symbol 'usb_transfer_stop' was not declared. Should it be static?
 * pd-video.c:1522:14: warning: symbol 'pd_video_poll' was not declared. Should it be static?
 * pd-video.c:1528:9: warning: symbol 'pd_video_read' was not declared. Should it be static?
 * pd-radio.c:164:5: warning: symbol 'tlg_fm_vidioc_g_tuner' was not declared. Should it be static?
 * pd-radio.c:206:5: warning: symbol 'fm_get_freq' was not declared. Should it be static?
 * pd-radio.c:249:5: warning: symbol 'fm_set_freq' was not declared. Should it be static?
 * pd-radio.c:261:5: warning: symbol 'tlg_fm_vidioc_g_ctrl' was not declared. Should it be static?
 * pd-radio.c:267:5: warning: symbol 'tlg_fm_vidioc_g_exts_ctrl' was not declared. Should it be static?
 * pd-radio.c:288:5: warning: symbol 'tlg_fm_vidioc_s_exts_ctrl' was not declared. Should it be static?
 * pd-radio.c:315:5: warning: symbol 'tlg_fm_vidioc_s_ctrl' was not declared. Should it be static?
 * pd-radio.c:321:5: warning: symbol 'tlg_fm_vidioc_queryctrl' was not declared. Should it be static?
 * pd-radio.c:340:5: warning: symbol 'tlg_fm_vidioc_querymenu' was not declared. Should it be static?
 * pd-main.c:58:12: warning: symbol 'firmware_name' was not declared. Should it be static?
 * pd-main.c:59:19: warning: symbol 'poseidon_driver' was not declared. Should it be static?
Signed-off-by: NMárton Németh <nm127@freemail.hu>
Acked-by: NHuang Shijie <shijie8@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Use NULL when calling a function with pointer parameter, initializing a
pointer and returning a pointer. This will remove the following sparse
warning at different locations (see "make C=1"):
 * warning: Using plain integer as NULL pointer
Signed-off-by: NMárton Németh <nm127@freemail.hu>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

When power management is not configured (CONFIG_PM) then some code is no longer
necessary.

This patch will remove the following compiler warnings:
 * pd-dvb.c: In function 'poseidon_fe_release':
 * pd-dvb.c:101: warning: unused variable 'pd'
 * pd-video.c:14: warning: 'pm_video_suspend' declared 'static' but never defined
 * pd-video.c:15: warning: 'pm_video_resume' declared 'static' but never defined
Signed-off-by: NMárton Németh <nm127@freemail.hu>
Acked-by: NHuang Shijie <shijie8@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

When temporarily there is no video signal, sometimes it takes more than 0.5
secs for the cx88 chip to generate a single frame. If a dma timeout occurs
during recording, it confuses the recording application (at least mencoder)
and the recording stops.

Since there is already an #if 0 for 2 seconds buffer timeout in the code
at the -hg development tree, re-enabling that seemed the most simple
solution.
Signed-off-by: NMarton Balint <cus@fazekas.hu>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Address a problem found in MythTV where if we are in digital mode, switch to
analog mode, and the switch back to digital mode, the first tuning request
after switching back to digital mode gets dropped.  This is because the au8522
maintains internal state, and would think the demod was already tuned to the
target frequency.

Thanks to Zaphod Beeblebrox for reporting this issue.
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

With applications like MythTV, switching inputs results in closing the digital
side and then immediately opening the analog side.  This exposes a race
condition where the dvb_frontend kernel thread powers down the chip and closes
the i2c gate even though we're in the middle of bringing up the analog part
of the chip (since the shutdown of the dvb_frontend kernel thread occurs
asychronously).

Introduce a construct to keep track of what mode we're in, and drop requests
to power down or management the gate if we've already switched to analog mode.

Thanks to Zaphod Beeblebrox for reporting this issue.
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

If the platform hooks are provided, soc_camera powers off the device
on close and powers it on on open. This resets the ADDRESS_MODE registers
which then can be different to the value the driver has computed for them.

This patch setups runtime pm usage for mt9t031 and uses the resume function
to write the ADDRESS_MODE registers in order to fix the above described
problem.
Signed-off-by: NValentin Longchamp <valentin.longchamp@epfl.ch>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

To save power soc-camera powers subdevices down, when they are not in use,
if this is supported by the platform. However, the V4L standard dictates,
that video nodes shall preserve configuration between uses. This requires
runtime power management, which is implemented by this patch. It allows
subdevice drivers to specify their runtime power-management methods, by
assigning a type to the video device.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: The first two parameters of soc_camera_limit_side() are usually pointers  to struct v4l2_rect elements. They are signed, so adjust the prototype  accordingly

This will remove the following sparse warning (see "make C=1"):

 * incorrect type in argument 1 (different signedness)
       expected unsigned int *start
       got signed int *<noident>

as well as a couple more signedness mismatches.
Signed-off-by: NMárton Németh <nm127@freemail.hu>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Fix a regression in the firmware loading time where it went from 1080 ms to
4700 ms.  This was noticed when the em28xx based HVR-950 took noticably longer
to load the driver.

Regression introduced in hg 12824.  The developer added an msleep() call with
an argument based on a newly introduced xc3028_ctrl field, which is left
initialized to zero for pretty much every board that is currently supported.
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

tm6000 sometimes can't read from i2c, but this is currently required for
tuner-xc2028 to work.

This patch adds an option to tuner-xc2028 to not rely on i2c reading.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Move the fifo reset from pxa_camera_start_capture to pxa_camera_irq direct
before the dma start after an end of frame interrupt to prevent images from
shifting because of old data at the begin of the frame.
Signed-off-by: NStefan Herbrechtsmeier <hbmeier@hni.uni-paderborn.de>
Acked-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Tested-by: NAntonio Ospite <ospite@studenti.unina.it>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

soc_mbus_bytes_per_line() returns -EINVAL on error but we store it in an
unsigned int so the test for less than zero doesn't work.  I think it
always returns "small" positive values so we can just cast it to int
here.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This fixes a regression of

	7d58289f (mx1: prefix SOC specific defines with MX1_ and deprecate old names)
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Never call dvb_frontend_detach if we failed to attach a frontend. This fixes
the following oops, which will be triggered by a missing stv090x module:

[    8.172997] DVB: registering new adapter (TT-Budget S2-1600 PCI)
[    8.209018] adapter has MAC addr = 00:d0:5c:cc:a7:29
[    8.328665] Intel ICH 0000:00:1f.5: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[    8.328753] Intel ICH 0000:00:1f.5: setting latency timer to 64
[    8.562047] DVB: Unable to find symbol stv090x_attach()
[    8.562117] BUG: unable to handle kernel NULL pointer dereference at 000000ac
[    8.562239] IP: [<e08b04a3>] dvb_frontend_detach+0x4/0x67 [dvb_core]

Ref http://bugs.debian.org/575207Signed-off-by: NBjørn Mork <bjorn@mork.no>
Cc: stable@kernel.org
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Send one DiSEqC byte to make sure that the pin is set to low level.
Signed-off-by: NOliver Endriss <o.endriss@gmx.de>
Reviewed-by: NManu Abraham <abraham.manu@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

An earlier regression fix for the mxb driver (V4L/DVB: saa7146_vv: fix
regression where v4l2_device was registered too late) caused a new
regression in the av7110 driver.

Reverted the old fix and fixed the problem in the mxb driver instead.
Tested on mxb and budget-av cards.

The real problem is that the saa7146 framework has separate probe()
and attach() driver callbacks which should be rolled into one. This
is now done for the mxb driver, but others should do the same. Lack
of hardware makes this hard to do, though. I hope to get hold of some
hexium cards and then I can try to improve the framework to prevent
this from happening again.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

v4l: fix config dependencies: mxb and saa7191 are V4L2 drivers, not V4L1
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

As part of upstream merge, set_params() function was removed from isif.c.
This requires removal of BUG_ON() and check for set_params ptr in
vpfe_capture.c. Without this kernel crash dump is seen while bootup on DM365

Also made following changes:-

 1) converted error messages to debug messages since it is not right to flood
    the console with error messages for user mistakes.
 2) returns -EINVAL if ioctl is not supported
Signed-off-by: NMuralidharan Karicheri <m-karicheri2@ti.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The 0461:0815 camera is spca561 based not spca508
Signed-off-by: NJohn Ellson <john.ellson@comcast.net>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The 046d:08da usb id shouldn't be associated with the stv06xx driver as they're
not compatible with each other.
This fixes a bug where Quickcam Messenger cams fail to use its proper driver
(gspca-zc3xx), rendering the camera inoperable.
Signed-off-by: NErik Andrén <erik.andren@gmail.com>
Tested-by: NGabriel Craciunescu <nix.or.die@googlemail.com>
Signed-off-by: NJean-François Moine <moinejf@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Use DECLARE_WAIT_QUEUE_HEAD_ONSTACK to make lockdep happy
Signed-off-by: NYong Zhang <yong.zhang0@gmail.com>
Signed-off-by: NJean-François Moine <moinejf@free.fr>
CC: Brian Johnson <brijohn@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

xawtv using DGA on a Radeon graphics card provides bogus
values to S_FBUF, which will then screw up overlay video:

https://bugs.launchpad.net/ubuntu/+source/xawtv/+bug/499734

This fixes the bytesperline value if it is off completely.
Signed-off-by: NMichael Hunold <michael@mihu.de>
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch fixes a bug in vpfe_probe() that doesn't call mutex_unlock() if memory
allocation for ccdc_cfg fails. See also the smatch warning report from Dan
Carpenter that shows this as an issue.
Signed-off-by: NMurali Karicheri <m-karicheri2@ti.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NVaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: NMuralidharan Karicheri <mkaricheri@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The previous loop goes until last == VIDEO_MAX_FRAME, so this could
potentially go one past the end of the loop.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Acked-by: NSakari Ailus <sakari.ailus@maxwell.research.nokia.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>