The encoder power domain is obviously tied to the encoder, so store it
in struct intel_encoder. This avoids some indirection.

v2: Rebase
Signed-off-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170222063431.10060-3-ander.conselvan.de.oliveira@intel.com

Remove workaround for swapped HPD pins in broxton A stepping, which is
pre-production hardware.

Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170203140316.20792-1-ander.conselvan.de.oliveira@intel.com

HDMI 2.0 recommends that we set the Q bits in the AVI infoframe
even when the sink does not support quantization range selection (QS=0).
According to CEA-861 we can do that as long as the Q we send matches
the default quantization range for the mode.

Previously I think I had misread the spec as saying that you can't
send a non-zero Q at all when QS=0. But that's not what the spec
actually says.

v2: Fix typo in commit message (Jani)
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170111125725.8086-5-ville.syrjala@linux.intel.comReviewed-by: NJani Nikula <jani.nikula@intel.com>
Acked-by: NEric Anholt <eric@anholt.net>

Pull the logic to populate the quantization range information
in the AVI infoframe into a small helper. We'll be adding a bit
more logic to it, and having it in a central place seems like a
good idea since it's based on the CEA-861 spec.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170111125725.8086-4-ville.syrjala@linux.intel.comReviewed-by: NJani Nikula <jani.nikula@intel.com>
Acked-by: NEric Anholt <eric@anholt.net>

Make the code selecting the RGB quantization range a little less magicy
by wrapping it up in a small helper.

v2: s/adjusted_mode/mode in vc4 to make it actually compile
v3: Add a comment proposed by Eric
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170111141835.25369-1-ville.syrjala@linux.intel.comReviewed-by: NJani Nikula <jani.nikula@intel.com>
Acked-by: NEric Anholt <eric@anholt.net>

Notifiations like mode change, hot plug and edid to
the audio driver are added. This is inturn used by the
audio driver for its functionality.

A new interface file capturing the notifications needed by the
audio driver is added
Signed-off-by: NPierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: NJerome Anand <jerome.anand@intel.com>
Acked-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Geminilake is mostly backwards compatible with broxton, so change most
of the IS_BROXTON() checks to IS_GEN9_LP(). Differences between the
platforms will be implemented in follow-up patches.

v2: Don't reuse broxton's path in intel_update_max_cdclk().
    Don't set plane count as in broxton.

v3: Rebase

v4: Include the check intel_bios_is_port_hpd_inverted().
    Commit message.

v5: Leave i915_dmc_info() out; glk's csr version != bxt's. (Rodrigo)

v6: Rebase.

v7: Convert a few mode IS_BROXTON() occurances in pps, ddi, dsi and pll
    code. (Rodrigo)

v8: Squash a couple of DDI patches with more conversions. (Rodrigo)

Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1480667037-11215-2-git-send-email-ander.conselvan.de.oliveira@intel.com

Pass dev_priv to intel_setup_outputs() and functions called by it, since
those are all intel i915 specific functions. Also, in the majority of
the functions dev_priv is used more often than dev. In the rare cases
where there are a few calls back into drm core, a local dev variable was
added.

v2: Don't convert dev to &dev_priv->drm in intel_dsi_init. (Ville)
Signed-off-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1479910904-11005-1-git-send-email-ander.conselvan.de.oliveira@intel.com

In all cases we can now obtain the relevant crtc_state/conn_state
from the relevant callbacks, which means all the ->config accesses
can be removed and the code cleaned up.

Changes since v1:
- cstate -> crtc_state
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/8b02a6b4-606a-e43a-b357-ad17f491525b@linux.intel.com
[mlankhorst: Reinstate missing comment]
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>

drm_select_eld requires mode_config.mutex and connection_mutex
because it looks at the connector list and at the legacy encoders.

This is not required, because when we call audio_codec_enable we know
which connector it was called for, so pass the state.

This also removes having to look at crtc->config.

Changes since v1:
- Use intel_crtc->pipe instead of drm_crtc_index. (Ville)
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1478609742-13603-8-git-send-email-maarten.lankhorst@linux.intel.comReviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>

This is the last connector still looking at crtc->config. Fix this.
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1478609742-13603-7-git-send-email-maarten.lankhorst@linux.intel.com

The VBT provides the platform a way to mix and match the DDI ports vs.
GMBUS pins. Currently we only trust the VBT for DDI E, which I suppose
has no standard GMBUS pin assignment. However, there are machines out
there that use a non-standard mapping for the other ports as well.
Let's start trusting the VBT on this one for all ports on DDI platforms.

I've structured the code such that other platforms could easily start
using this as well, by simply filling in the ddi_port_info. IIRC there
may be CHV system that might actually need this.

v2: Include a commit message, include a debug message during init

Cc: stable@vger.kernel.org
Cc: Maarten Maathuis <madman2003@gmail.com>
Tested-by: NMaarten Maathuis <madman2003@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=97877Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1476208368-5710-3-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NJim Bride <jim.bride@linux.intel.com>
(cherry picked from commit e4ab73a1)
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

Unify our approach to things by passing around dev_priv instead of dev.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1477946245-14134-8-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NChris Wilson <chris@chris-wilson.co.uk>

The VBT provides the platform a way to mix and match the DDI ports vs.
GMBUS pins. Currently we only trust the VBT for DDI E, which I suppose
has no standard GMBUS pin assignment. However, there are machines out
there that use a non-standard mapping for the other ports as well.
Let's start trusting the VBT on this one for all ports on DDI platforms.

I've structured the code such that other platforms could easily start
using this as well, by simply filling in the ddi_port_info. IIRC there
may be CHV system that might actually need this.

v2: Include a commit message, include a debug message during init

Cc: stable@vger.kernel.org
Cc: Maarten Maathuis <madman2003@gmail.com>
Tested-by: NMaarten Maathuis <madman2003@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=97877Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1476208368-5710-3-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NJim Bride <jim.bride@linux.intel.com>

Saves 944 bytes of .rodata strings and 128 bytes of .text.

v2: Add parantheses around dev_priv. (Ville Syrjala)
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NDavid Weinehall <david.weinehall@linux.intel.com>
Acked-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: NJani Nikula <jani.nikula@linux.intel.com>
Acked-by: NChris Wilson <chris@chris-wilson.co.uk>
Acked-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>

Saves 864 bytes of .rodata strings and ~100 of .text.

v2: Add parantheses around dev_priv. (Ville Syrjala)
v3: Rebase.
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NDavid Weinehall <david.weinehall@linux.intel.com>
Acked-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: NJani Nikula <jani.nikula@linux.intel.com>
Acked-by: NChris Wilson <chris@chris-wilson.co.uk>
Acked-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>

Saves 472 bytes of .rodata strings.

v2: Add parantheses around dev_priv. (Ville Syrjala)
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NDavid Weinehall <david.weinehall@linux.intel.com>
Acked-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: NJani Nikula <jani.nikula@linux.intel.com>
Acked-by: NChris Wilson <chris@chris-wilson.co.uk>
Acked-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>

Saves 1392 bytes of .rodata strings.

Also change a few function/macro prototypes in i915_gem_gtt.c
from dev to dev_priv where it made more sense to do so.

v2: Add parantheses around dev_priv. (Ville Syrjala)
v3: Mention function prototype changes. (David Weinehall)
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: David Weinehall <david.weinehall@linux.intel.com>
Acked-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: NJani Nikula <jani.nikula@linux.intel.com>
Acked-by: NChris Wilson <chris@chris-wilson.co.uk>
Acked-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: NDavid Weinehall <david.weinehall@linux.intel.com>

Saves 4472 bytes of .rodata strings.

v2: Add parantheses around dev_priv. (Ville Syrjala)
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NDavid Weinehall <david.weinehall@linux.intel.com>
Acked-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: NJani Nikula <jani.nikula@linux.intel.com>
Acked-by: NChris Wilson <chris@chris-wilson.co.uk>
Acked-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>

More .rodata string saving by avoid __I915__ magic inside WARNs.

v2: Add parantheses around dev_priv. (Ville Syrjala)
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NDavid Weinehall <david.weinehall@linux.intel.com>
Acked-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: NJani Nikula <jani.nikula@linux.intel.com>
Acked-by: NChris Wilson <chris@chris-wilson.co.uk>
Acked-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>

This saves 1872 bytes of .rodata strings.

v2:
 * Rebase.
 * Add parantheses around dev_priv. (Ville Syrjala)
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NDavid Weinehall <david.weinehall@linux.intel.com>
Acked-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: NJani Nikula <jani.nikula@linux.intel.com>
Acked-by: NChris Wilson <chris@chris-wilson.co.uk>
Acked-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>

This saves 3248 bytes of .rodata strings.

v2: Add parantheses around dev_priv. (Ville Syrjala)
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NDavid Weinehall <david.weinehall@linux.intel.com>
Acked-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: NJani Nikula <jani.nikula@linux.intel.com>
Acked-by: NChris Wilson <chris@chris-wilson.co.uk>
Acked-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>

It's perfectly legal for the sink to support 12bpc only for
some lower resolution modes, while the higher resolution modes
can only be used with 8bpc. So let's take the sink's max TMDS clock
into account before we go and decide that a particular mode can
be used with 12bpc.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NAnder Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1475070703-6435-11-git-send-email-ville.syrjala@linux.intel.com

Storing the port enum in intel_encoder makes it convenient to know the
port attached to an encoder. Moving the port information up from
intel_digital_port to intel_encoder avoids unecessary intel_digital_port
access and handles MST encoders cleanly without requiring conditional
checks for them (thanks danvet).

v2:
Renamed the port enum member from 'attached_port' to 'port' (danvet)
Fixed missing initialization of port in intel_sdvo.c (danvet)

v3:
Fixed missing initialization of port in intel_crt.c (Ville)

v4:
Storing port for DVO encoders too.
Signed-off-by: NDhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: NLyude <cpaul@redhat.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1474334681-22690-3-git-send-email-dhinakaran.pandiyan@intel.com

This reverts commit 237ed86c.

Our current implementation of live status check (repeat 9 times
with 10ms delays between each attempt as a workaround for
buggy displays) imposes a rather serious penalty, time wise,
on intel_hdmi_detect().  Since we we already skip live status
checks on platforms before gen 7, and since we seem to have
coped quite well before the live status check was introduced
for newer platforms too, the previous behaviour is probably
preferable, at least unless someone can point to a use-case
that the live status check improves (apart from "Bspec says so".)
Signed-off-by: NDavid Weinehall <david.weinehall@linux.intel.com>
Fixes: 237ed86c ("drm/i915: Check live status before reading edid")
Fixes: f8d03ea0 ("drm/i915: increase the tries for HDMI hotplug live status checking")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=97139
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=94014Acked-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org # v4.4+
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20160817124748.31208-1-david.weinehall@linux.intel.com

Some places iterate over connector_state to find the right
connector, pass it along as argument.
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470755054-32699-7-git-send-email-maarten.lankhorst@linux.intel.comReviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This is mostly code churn, with exception of a few places:
- intel_display.c has changes in intel_sanitize_encoder
- intel_ddi.c has intel_ddi_fdi_disable calling intel_ddi_post_disable,
  and required a function change. Also affects intel_display.c
- intel_dp_mst.c passes a NULL crtc_state and conn_state to
  intel_ddi_post_disable for shutting down the real encoder.

  If we would pass conn_state, then conn_state->connector !=
  intel_dig_port->connector and conn_state->best_encoder !=
  to_intel_encoder(intel_dig_port).

  We also shouldn't pass crtc_state, because in that case the
  disabling sequence may potentially be different depending on
  which crtc is disabled last. Nice way to introduce bugs.

No other functional changes are done, diff stat is already huge.
Each encoder type will need to be fixed to use the atomic states
separately.
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470755054-32699-6-git-send-email-maarten.lankhorst@linux.intel.comReviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

With the output_types bitmask there's no need to loop through
the encoders anymore when checking for HDMI+non-HDMI cloning.

v2: Use output_types bitmask
v3: Fix the logic to really check that there are no non-HDMI encoders
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> (v2)
Link: http://patchwork.freedesktop.org/patch/msgid/1466621833-5054-11-git-send-email-ville.syrjala@linux.intel.com

Since drm_i915_private is now a subclass of drm_device we do not need to
chase the drm_i915_private->dev backpointer and can instead simply
access drm_i915_private->drm directly.

   text	   data	    bss	    dec	    hex	filename
1068757	   4565	    416	1073738	 10624a	drivers/gpu/drm/i915/i915.ko
1066949	   4565	    416	1071930	 105b3a	drivers/gpu/drm/i915/i915.ko

Created by the coccinelle script:
@@
struct drm_i915_private *d;
identifier i;
@@
(
- d->dev->i
+ d->drm.i
|
- d->dev
+ &d->drm
)

and for good measure the dev_priv->dev backpointer was removed entirely.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NMatthew Auld <matthew.auld@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1467711623-2905-4-git-send-email-chris@chris-wilson.co.uk

Since we now subclass struct drm_device, we can save pointer dances by
noting the equivalence of struct drm_device and struct drm_i915_private,
i.e. by using to_i915().

   text    data     bss     dec     hex filename
1073824    4562     416 1078802  107612 drivers/gpu/drm/i915/i915.ko
1068976    4562     416 1073954  106322 drivers/gpu/drm/i915/i915.ko

Created by the coccinelle script:

@@
expression E;
identifier p;
@@
- struct drm_i915_private *p = E->dev_private;
+ struct drm_i915_private *p = to_i915(E);
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NDave Gordon <david.s.gordon@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1467628477-25379-1-git-send-email-chris@chris-wilson.co.uk

Defer connector registration from during construction to the driver
registration phase. This is important for ordering the action correctly,
e.g. not using debugfs before it is ready.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1466773227-7994-4-git-send-email-chris@chris-wilson.co.uk

Currently the backlight is being registered in the load phase (before
the display and its objects are registered). Move the backlight
registration into the analogous phase by performing it from the
connector registration, just after its creation.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1466773227-7994-3-git-send-email-chris@chris-wilson.co.uk

We now have a connector->func that serves the same purpose as our own
intel_connector->unregister vfunc allowing us to unwrap ourselves and
use drm_connector_register() (and friends) as the central function.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1466160034-12173-2-git-send-email-chris@chris-wilson.co.uk

For all outputs except dp_mst, we have a 1:1 relationship between
connectors and encoders and the driver is relying on the atomic helpers:
we can drop the custom ->best_encoder() implementation and let the core
call drm_atomic_helper_best_encoder() for us.
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1465300095-16971-7-git-send-email-boris.brezillon@free-electrons.com

Apparently some CHV boards failed to hook up the port presence straps
for HDMI ports as well (earlier we assumed this problem only affected
eDP ports). So let's check the VBT in addition to the strap, and if
either one claims that the port is present go ahead and register the
relevant connector.

While at it, change port D to register DP before HDMI as we do for ports
B and C since
commit 457c52d8 ("drm/i915: Only ignore eDP ports that are connected")

Also print a debug message when we register a HDMI connector to aid
in diagnosing missing/incorrect ports. We already had such a print for
DP/eDP.

v2: Improve the comment in the code a bit, note the port D change in
    the commit message

Cc: Radoslav Duda <radosd@radosd.com>
Tested-by: NRadoslav Duda <radosd@radosd.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=96321Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464945463-14364-1-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
(cherry picked from commit 22f35042)
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

Apparently some CHV boards failed to hook up the port presence straps
for HDMI ports as well (earlier we assumed this problem only affected
eDP ports). So let's check the VBT in addition to the strap, and if
either one claims that the port is present go ahead and register the
relevant connector.

While at it, change port D to register DP before HDMI as we do for ports
B and C since
commit 457c52d8 ("drm/i915: Only ignore eDP ports that are connected")

Also print a debug message when we register a HDMI connector to aid
in diagnosing missing/incorrect ports. We already had such a print for
DP/eDP.

v2: Improve the comment in the code a bit, note the port D change in
    the commit message

Cc: Radoslav Duda <radosd@radosd.com>
Tested-by: NRadoslav Duda <radosd@radosd.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=96321Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464945463-14364-1-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NChris Wilson <chris@chris-wilson.co.uk>

Rather than let the core generate usless encoder names, let's pass in
something that actually identifies the piece of hardware we're dealing
with.

v2: Use 'DSI %c' instead of 'MIPI %c' for DSI encoders (Jani)
v3: Use port_name() in DSI code since we have it
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464371966-15190-7-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NChris Wilson <chris@chris-wilson.co.uk>

Set the lane count for HDMI to 4. This will make it easier to
unduplicate CHV phy code.

This also fixes the the soft reset programming for HDMI with CHV. After
commit a8f327fb ("drm/i915: Clean up CHV lane soft reset
programming"), it wouldn't set the right bits for PCS23 since it relied
on a lane count that was never set.

v2: Set lane_count in *_get_config() to please state checker. (0day)
v3: Set lane_count for DDI in DVI mode too. (CI)
v4: Add note about CHV soft lane reset. (Ander)

Fixes: a8f327fb ("drm/i915: Clean up CHV lane soft reset programming")
Signed-off-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: NJim Bride <jim.bride@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461761065-21195-2-git-send-email-ander.conselvan.de.oliveira@intel.com
(cherry picked from commit d4d6279a)
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

DP dual mode type 1 DVI adaptors aren't required to implement any
registers, so it's a bit hard to detect them. The best way would
be to check the state of the CONFIG1 pin, but we have no way to
do that. So as a last resort, check the VBT to see if the HDMI
port is in fact a dual mode capable DP port.

v2: Deal with VBT code reorganization
    Deal with DRM_DP_DUAL_MODE_UNKNOWN
    Reduce DEVICE_TYPE_DP_DUAL_MODE_BITS a bit
    Accept both DP and HDMI dvo_port in VBT as my BSW
    at least declare its DP port as HDMI :(
v3: Ignore DEVICE_TYPE_NOT_HDMI_OUTPUT (Shashank)

Cc: stable@vger.kernel.org
Cc: Tore Anderson <tore@fud.no>
Reported-by: NTore Anderson <tore@fud.no>
Fixes: 7a0baa62 ("Revert "drm/i915: Disable 12bpc hdmi for now"")
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Shashank Sharma <shashank.sharma@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1462362322-31278-1-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NShashank Sharma <shashank.sharma@intel.com>
(cherry picked from commit d6199256)
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

To save a bit of power, let's try to turn off the TMDS output buffers
in DP++ adaptors when we're not driving the port.

v2: Let's not forget DDI, toss in a debug message while at it
v3: Just do the TMDS output control based on adaptor type. With the
    helper getting passed the type, we wouldn't actually have to
    check at all in the driver, but the check eliminates the debug
    output more honest

Cc: stable@vger.kernel.org
Cc: Tore Anderson <tore@fud.no>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Shashank Sharma <shashank.sharma@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1462216105-20881-4-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NShashank Sharma <shashank.sharma@intel.com>
(cherry picked from commit b2ccb822)
Signed-off-by: NJani Nikula <jani.nikula@intel.com>