When initiating a transparent eSCO connection, make use of T2 settings
at first try. T2 is the recommended settings from HFP 1.6 WideBand
Speech. Upon connection failure, try T1 settings.

When CVSD is requested and eSCO is supported, try to establish eSCO
connection using S3 settings. If it fails, fallback in sequence to S2,
S1, D1, D0 settings.

To know which setting should be used, conn->attempt is used. It
indicates the currently ongoing SCO connection attempt and can be used
as the index for the fallback settings table.

These setting and the fallback order are described in Bluetooth HFP 1.6
specification p. 101.
Signed-off-by: NFrédéric Dalleau <frederic.dalleau@linux.intel.com>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

Synchronous Connection Complete event can return error "Connection
Rejected due to Limited resources (0x10)".
Handling this error is required for SCO connection fallback. This error
happens when the server tried to accept the connection but failed to
negotiate settings.
This error code has been verified experimentally by sending a T2 request
to a T1 only SCO listener.

Client dump follows :

< HCI Command (0x01|0x0028) plen 17 [hci0] 3.696064
        Handle: 12
        Transmit bandwidth: 8000
        Receive bandwidth: 8000
        Max latency: 13
        Setting: 0x0003
        Retransmission effort: Optimize for link quality (0x02)
        Packet type: 0x0380
> HCI Event (0x0f) plen 4 [hci0] 3.697034
      Setup Synchronous Connection (0x01|0x0028) ncmd 1
        Status: Success (0x00)
> HCI Event (0x2c) plen 17 [hci0] 3.736059
        Status: Connection Rejected due to Limited Resources (0x0d)
        Handle: 0
        Address: xx:xx:xx:xx:xx:AB (OUI 70-F3-95)
        Link type: eSCO (0x02)
        Transmission interval: 0x0c
        Retransmission window: 0x06
        RX packet length: 60
        TX packet length: 60
        Air mode: Transparent (0x03)

Server dump follows :

> HCI Event (0x04) plen 10 [hci0] 4.741513
        Address: xx:xx:xx:xx:xx:D9 (OUI 20-68-9D)
        Class: 0x620100
          Major class: Computer (desktop, notebook, PDA, organizers)
          Minor class: Uncategorized, code for device not assigned
          Networking (LAN, Ad hoc)
          Audio (Speaker, Microphone, Headset)
          Telephony (Cordless telephony, Modem, Headset)
        Link type: eSCO (0x02)
< HCI Command (0x01|0x0029) plen 21 [hci0] 4.743269
        Address: xx:xx:xx:xx:xx:D9 (OUI 20-68-9D)
        Transmit bandwidth: 8000
        Receive bandwidth: 8000
        Max latency: 13
        Setting: 0x0003
        Retransmission effort: Optimize for link quality (0x02)
        Packet type: 0x03c1
> HCI Event (0x0f) plen 4 [hci0] 4.745517
      Accept Synchronous Connection (0x01|0x0029) ncmd 1
        Status: Success (0x00)
> HCI Event (0x2c) plen 17 [hci0] 4.749508
        Status: Connection Rejected due to Limited Resources (0x0d)
        Handle: 0
        Address: xx:xx:xx:xx:xx:D9 (OUI 20-68-9D)
        Link type: eSCO (0x02)
        Transmission interval: 0x0c
        Retransmission window: 0x06
        RX packet length: 60
        TX packet length: 60
        Air mode: Transparent (0x03)
Signed-off-by: NFrédéric Dalleau <frederic.dalleau@linux.intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

Older Bluetooth devices may not support Setup Synchronous Connection or
SCO transparent data. This is indicated by the corresponding LMP feature
bits. It is not possible to know if the adapter support these features
before setting BT_VOICE option since the socket is not bound to an
adapter. An adapter can also be added after the socket is created. The
socket can be bound to an address before adapter is plugged in.

Thus, on a such adapters, if user request BT_VOICE_TRANSPARENT, outgoing
connections fail on connect() and returns -EOPNOTSUPP. Incoming
connections do not fail. However, they should only be allowed depending
on what was specified in Write_Voice_Settings command.

EOPNOTSUPP is choosen because connect() system call is failing after
selecting route but before any connection attempt.
Signed-off-by: NFrédéric Dalleau <frederic.dalleau@linux.intel.com>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

This patch defines constants and macro for transparent data LMP
features. It refers to Bluetooth Core V4.0 specification, Part C, Chap
3.3 which defines LMP feature mask.
Signed-off-by: NFrédéric Dalleau <frederic.dalleau@linux.intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

In order to establish a transparent SCO connection, the correct settings
must be specified in the Setup Synchronous Connection request. For that,
a setting field is added to ACL connection data to set up the desired
parameters. The patch also removes usage of hdev->voice_setting in CVSD
connection and makes use of T2 parameters for transparent data.
Signed-off-by: NFrédéric Dalleau <frederic.dalleau@linux.intel.com>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

When an incoming eSCO connection is requested, check the selected voice
setting and reply appropriately. Voice setting should have been
negotiated previously.  For example, in case of HFP, the codec is
negotiated using AT commands on the RFCOMM channel. This patch only
changes replies for socket with deferred setup enabled.
Signed-off-by: NFrédéric Dalleau <frederic.dalleau@linux.intel.com>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

This patch defines constants for SCO airmode from SCO voice setting. It
refers to Bluetooth Core V4.0 specification, Part E, Chap 6.12 which
describe SCO voice setting format.
Signed-off-by: NFrédéric Dalleau <frederic.dalleau@linux.intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

This patch extends the current Bluetooth socket options with BT_VOICE.
This is intended to choose voice data type at runtime. It only applies
to SCO sockets. Incoming connections shall be setup during deferred
setup. Outgoing connections shall be setup before connect(). The desired
setting is stored in the SCO socket info. This patch declares needed
members, modifies getsockopt() and setsockopt().
Signed-off-by: NFrédéric Dalleau <frederic.dalleau@linux.intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

From Bluetooth Core v4.0 specification, 7.1.8 Accept Connection Request
Command "When accepting synchronous connection request, the Role
parameter is not used and will be ignored by the BR/EDR Controller."
Signed-off-by: NFrédéric Dalleau <frederic.dalleau@linux.intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

hci_connect is a super function for connecting hci protocols. But the
voice_setting parameter (introduced in subsequent patches) is only
needed by SCO and security requirements are not needed for SCO channels.
Thus, it makes sense to have a separate function for SCO.
Signed-off-by: NFrédéric Dalleau <frederic.dalleau@linux.intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

In rfcomm_tty_cleanup we purge the dlc->tx_queue which may contain
socket buffers referencing the tty_port and thus preventing the tty_port
destruction.
Signed-off-by: NGianluca Anzolin <gianluca@sottospazio.it>
Reviewed-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

The tty_port can be released in two cases: when we get a HUP in the
functions rfcomm_tty_hangup() and rfcomm_dev_state_change(). Or when the
user releases the device in rfcomm_release_dev().

In these cases we set the flag RFCOMM_TTY_RELEASED so that no other
function can get a reference to the tty_port.
The use of !test_and_set_bit(RFCOMM_TTY_RELEASED) ensures that the
'initial' tty_port reference is only dropped once.

The rfcomm_dev_del function is removed becase it isn't used anymore.
Signed-off-by: NGianluca Anzolin <gianluca@sottospazio.it>
Reviewed-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

Implement .activate, .shutdown and .carrier_raised methods of tty_port
to manage the dlc, moving the code from rfcomm_tty_install() and
rfcomm_tty_cleanup() functions.

At the same time the tty .open()/.close() and .hangup() methods are
changed to use the tty_port helpers that properly call the
aforementioned tty_port methods.
Signed-off-by: NGianluca Anzolin <gianluca@sottospazio.it>
Reviewed-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

Move the tty_struct initialization from rfcomm_tty_open() to
rfcomm_tty_install() and do the same for the cleanup moving the code from
rfcomm_tty_close() to rfcomm_tty_cleanup().

Add also extra error handling in rfcomm_tty_install() because, unlike
.open()/.close(), .cleanup() is not called if .install() fails.
Signed-off-by: NGianluca Anzolin <gianluca@sottospazio.it>
Reviewed-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

The current code removes the device from the device list in several
places. Do it only in the destructor instead and in the error path of
rfcomm_add_dev() if the device couldn't be initialized.
Signed-off-by: NGianluca Anzolin <gianluca@sottospazio.it>
Reviewed-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

In net/bluetooth/rfcomm/tty.c the struct tty_struct is used without
taking references. This may lead to a use-after-free of the rfcomm tty.

Fix this by taking references properly, using the tty_port_* helpers
when possible.

The raw assignments of dev->port.tty in rfcomm_tty_open/close are
addressed in the later commit 'rfcomm: Implement .activate, .shutdown
and .carrier_raised methods'.
Signed-off-by: NGianluca Anzolin <gianluca@sottospazio.it>
Reviewed-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

In case of a Low Energy only controller it makes no sense to configure
the full BR/EDR event mask. It will just enable events that can not be
send anyway and there is no guarantee that such a controller will accept
this value.

Use event mask 0x90 0xe8 0x04 0x02 0x00 0x80 0x00 0x20 for LE-only
controllers which enables the following events:

          Disconnection Complete
          Encryption Change
          Read Remote Version Information Complete
          Command Complete
          Command Status
          Hardware Error
          Number of Completed Packets
          Data Buffer Overflow
          Encryption Key Refresh Complete
          LE Meta

This is according to Core Specification, Part E, Section 3.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

When a socket is in deferred state there does actually exist an
underlying connection even though the connection state is not yet
BT_CONNECTED. In the deferred state it should therefore be allowed to
get socket options that usually depend on a connection, such as
SCO_OPTIONS and SCO_CONNINFO.

This patch fixes the behavior of some user space code that behaves as
follows without it:

$ sudo tools/btiotest -i 00:1B:DC:xx:xx:xx -d -s
accept=2 reject=-1 discon=-1 defer=1 sec=0 update_sec=0 prio=0 voice=0x0000
Listening for SCO connections
bt_io_get(OPT_DEST): getsockopt(SCO_OPTIONS): Transport endpoint is not connected (107)
Accepting connection
Successfully connected to 60:D8:19:xx:xx:xx. handle=43, class=000000

The conditions that the patch updates the if-statements to is taken from
similar code in l2cap_sock.c which correctly handles the deferred state.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

There are two places where DIV_ROUND_UP may be used. It makes code a bit
clearer.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

The usage of strict_strtol() is not preferred, because
strict_strtol() is obsolete. Thus, kstrtol() should be
used.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

The USB hid implementation does retrieve the reports during the start.
However, this implementation does not call the HID command GET_REPORT
(which would fetch the current status of each report), but use the
DATA command, which is an Output Report (so transmitting data from the
host to the device).
The Wiimote controller is already guarded against this problem in the
protocol, but it is not conformant to the specification to set all the
reports to 0 on start.
Signed-off-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: NDavid Herrmann <dh.herrmann@gmail.com>
Acked-by: NJiri Kosina <jkosina@suse.cz>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

We can re-enable hidinput_input_event to allow the leds of bluetooth
keyboards to be set.
Now the callbacks uses hid core to retrieve the right HID report to
send, so this version is safer.
Signed-off-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: NDavid Herrmann <dh.herrmann@gmail.com>
Acked-by: NJiri Kosina <jkosina@suse.cz>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

Trivial change in the coding style.
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

Replace the occurrences of integer literals in hci_event.c with the
newly introduced macros in hci.h.
Signed-off-by: NMikel Astiz <mikel.astiz@bmw-carit.de>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

Make the code in hci_get_auth_req() more readable by using the
defined macros instead of inlining magic numbers.
Signed-off-by: NMikel Astiz <mikel.astiz@bmw-carit.de>
Signed-off-by: NTimo Mueller <timo.mueller@bmw-carit.de>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

Add macros for the HCI capabilities as described in the Bluetooth Core
Specification v4.0, Volume 2, part E, section 7.1.29.
Signed-off-by: NMikel Astiz <mikel.astiz@bmw-carit.de>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

bgmac uses bcm47xx_nvram.h which is only available when BCM47XX was
selected. Earlier BCMA_HOST_SOC depended on BCM47XX so this was not
build on any other archs, but that changed. We should modify this
driver to get access to the nvram or the variables through platform
data.

This fixes a build problem in linux-next reported by Stephen Rothwell:

drivers/net/ethernet/broadcom/bgmac.c:19:27: fatal error: bcm47xx_nvram.h: No such file or directory
 #include <bcm47xx_nvram.h>
                           ^
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Reported-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

taken from Ralink linux and windows drivers:

0x1b75, 0x7733 AirLive 450Mbps Wireless-N Dual Band USB Adapter
0x0b05, 0x17bc ASUS USB-N66 450Mbps Dual Band USB Adapter
0x0b05, 0x17ad ASUS USB-N66 Dual Band N Network Adapter
0x050d, 0x1103 Belkin Wireless Adapter
0x148f, 0xf301 Cameo Ralink3573 3x3 single band USB dongle
0x7392, 0x7733 Edimax
0x0e66, 0x0020 Hawking HD45U Dual Band USB Wireless-N Adapter
0x0e66, 0x0021 Hawking HD45U Dual Band Wls-450N Adapter
0x04bb, 0x094e I-O DATA WN-AG450U Wireless LAN Adapter
0x0789, 0x016b Logitec LAN-W450AN/U2
0x0846, 0x9012 NETGEAR WNDA4100 N900 Wireless Dual Band USB Adapter
0x0846, 0x9019 NETGEAR WNDA4200D Wireless Dual Band USB Adapter
0x2019, 0xed19 Planex GW-USDual450
0x148f, 0x3573 Ralink 802.11n USB Wireless LAN Card
0x0df6, 0x0067 Sitecom Wireless Dualband Network Adapter N750 X6
0x0df6, 0x006a Sitecom Wireless Dualband Network Adapter N900 X7
0x0586, 0x3421 ZyXEL Dual-Band Wireless N450 USB Adapter

Cc: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: Helmut Schaa <helmut.schaa@googlemail.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: users@rt2x00.serialmonkey.com
Cc: linux-wireless@vger.kernel.org
Signed-off-by: NXose Vazquez Perez <xose.vazquez@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When antenna diversity combining is enabled in the EEPROM,
the initial values for the MAIN/ALT config have to be
programmed correctly. This patch adds it for AR9285.

Since the diversity combining macros are common to all chip
families, remove the redundant AR9285 macros and move the
definitions to phy.h.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We support maximum simultaneous 2 non-AP station interfaces and
they can assume role of Station/P2P client/P2P GO.
Advertise this support to cfg80211 so that concurrent P2P/STA
operation is possible.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We already have 'struct mwifiex_ie_types_header' with same
definition. Hence host_cmd_tlv is removed in this patch.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

For PCIe cards, when wrong firmware is downloaded, firmware is
failed to be ready in 10 seconds. We should return an error at
this point. But currently we are sending first command to firmware.
As expected firmware doesn't respond to this command and command
timeout occurs.

This patch fixes the problem by removing unnecessary 'ret'
variable modifications in "if (ret) {" block.
The block is just supposed to update "adapter->winner" flag.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It is observed that when wrong firmware is downloaded for
PCIe card, system hangs for 10 seconds. The reason is mdelay()
is used when firmware status is polled.

Replace mdelay with msleep(non-blocking API) to fix the issue.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

After downloading the firmware, firmware status is checked by
reading a register. Polling interval is 100 msecs. Therefore 100
retries means the status is checked for 10 secs which is more than
sufficient for firmware to get ready.

This patch removes 1000 retries macro usage, because 100secs
time is not practical.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Clear the data pointer stored in USB interface structure in
this handler. This helps to return from mwifiex_usb_disconnect()
if driver deinitialization is already performed while handling
an error path for mwifiex_usb_probe().

USB8797 card gets enumerated twice. First enumeration is for
firmware download and second enumeration expects firmware
initialization. mwifiex_usb_probe() always takes care of
deinitialization for first enumeration after firmware download.

Also, this change matches our handling for SDIO and PCIe
interfaces.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

As if_ops.init_if() is called in mwifiex_register(),
corresponding cleanup routine should be called in
mwifiex_unregister().

Currently it's there in mwifiex_adapter_cleanup(), hence
interface specific cleanup is not performed if driver
initialization is failed.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It is already there in mwifiex_unregister(). So unnecessary
call in mwifiex_adapter_cleanup() is removed in this patch.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Currently it is in mwifiex_adapter_cleanup() which doesn't get
called if driver initialization is failed causing memory leak.

scan_delay_timer is initialized in mwifiex_register(), so it
should be deleted in mwifiex_unregister(). Hence it has been
moved to appropriate place.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If reboot command is issued when device is in connected state,
system hangs while booting. This issue is fixed by doing cleanup
in shutdown handler.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>