Add the firmware API name to the struct iwl_wowlan_gtk_status.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

According to the spec when a BA session is started there
is a timeout set for the session in the ADDBA request.
If there is not activity on the TA/TID then the session
expires and a DELBA is sent.
In order to check for the timeout, data must be shared
among the rx queues.
Add a timer that runs as long as BA session is active
for the station and stops aggregation session if needed.
This patch also lays the infrastructure for the reordering
buffer which will be enabled in the next patches.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Currently the sync notification is a type of notification. However, it
is better fitted as an attribute of a notification, since there might
be another message in the payload (delba for instance) that should be
sent while control path is waiting for all queues to process.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

mac80211 will call the driver whenever there is a race between
RSS queues and control path that requires a processing of all
pending frames in RSS queues.
Implement that by utilizing the internal notification mechanism:
queue a message to all queues. When the message is received on
a queue it decrements the atomic counter. This guarantees that
all pending frames in the RX queue were processed since the message
is in order inside the queue.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Add new 8265 series SDIO ID.
Signed-off-by: NMordechai Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Support sending P2P device frames should be sent from
queue #2, as required in DQA mode.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

In DQA mode, allocate a dedicated queue (#9) for P2P GO/soft
AP probe responses.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

The TSO code creates A-MSDUs from a single large send. Each
A-MSDU is an skb and skb->len doesn't include the number of
bytes which need to be added for the headers being added
(subframe header, TCP header, IP header, SNAP, padding).

To be able to set the right value in the Tx command, we
put the number of bytes added by those headers in
driver_data in iwl_mvm_tx_tso and use this value in
iwl_mvm_set_tx_cmd.

The problem by setting this value in driver_data is that
it overrides the ieee80211_tx_info. The bug manifested
itself when we send P2P related frames in CCK since the
rate in ieee80211_tx_info is zero-ed. This of course is
a violation of the P2P specification.

To fix this, copy the original ieee80211_tx_info to the
stack and pass it to the functions which need it.
Assign the number of bytes added by the headers to the
driver_data inside the skb itself.

Fixes: a6d5e32f ("iwlwifi: mvm: send large SKBs to the transport")
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This enum is already perfectly aliased to enum nl80211_band, and
the only reason for it is that we get IEEE80211_NUM_BANDS out of
it. There's no really good reason to not declare the number of
bands in nl80211 though, so do that and remove the cfg80211 one.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The firwmare file can come with data that is relevant for paging. This
data is availablet to the firmware upon request, but it stored in the
host's memory. During the firmware init flow, the driver configures the
firmware so that the firwmare knows where is the data.
When paging is used, the variable paging_mem_size is the number of bytes
that are available through paging. This variable is not zeror-ed if the
driver fails to configure the paging in the firmware, but the memory is
freed which is inconsistent.
This inconsistency led to a NULL pointer dereference in the code that
collects the debug data.

Fix this by zero-ing the paging_mem_size variable and NULLify the
relevant pointers, so that the code that collects the debug data will
know that the paging data is not available.
Signed-off-by: NMatti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The firwmare name for 8000 is iwlwifi-8000C. The C is
appended based on a value read from a register. This
allows to load different firwmare versions based on
the hardware step during development. Now that the
hardware development is completed, we can hard code
the 'C' and along the way, fix the input to
MODULE_FIRMWARE.

This fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=116041Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Gscan capabilities were updated with new capabilities supported
by the device. Update GSCAN capabilities TLV and avoid to WARN
if the firmware does not have the new capabilities.
Signed-off-by: NAyala Beker <ayala.beker@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Add new 8265 series PCI IDs.
Signed-off-by: NOren Givon <oren.givon@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Enables the use of multiple transmit and receive scrqs allowing the ibmvnic
driver to take advantage of multiqueue functionality. To achieve this, the
driver must implement the process of negotiating the maximum number of
queues allowed by the server. Initially, the driver will attempt to login
with the maximum number of tx and rx queues supported by the server. If
the server fails to allocate the requested number of scrqs, it will return
partial success in the login response. In this case, we must reinitiate
the login process from the request capabilities stage and attempt to login
requesting fewer scrqs.
Signed-off-by: NJohn Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The switchdev design implies that a software error should not happen in
the commit phase since it must have been previously reported in the
prepare phase. If an hardware error occurs during the commit phase,
there is nothing switchdev can do about it.

The DSA layer separates port_vlan_prepare and port_vlan_add for
simplicity and convenience. If an hardware error occurs during the
commit phase, there is no need to report it outside the driver itself.

Make the DSA port_vlan_add routine return void for explicitness.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The switchdev design implies that a software error should not happen in
the commit phase since it must have been previously reported in the
prepare phase. If an hardware error occurs during the commit phase,
there is nothing switchdev can do about it.

The DSA layer separates port_fdb_prepare and port_fdb_add for simplicity
and convenience. If an hardware error occurs during the commit phase,
there is no need to report it outside the DSA driver itself.

Make the DSA port_fdb_add routine return void for explicitness.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The DSA layer doesn't care about the return code of the port_stp_update
routine, so make it void in the layer and the DSA drivers.

Replace the useless dsa_slave_stp_update function with a
dsa_slave_stp_state function used to reply to the switchdev
SWITCHDEV_ATTR_ID_PORT_STP_STATE attribute.

In the meantime, rename port_stp_update to port_stp_state_set to
explicit the state change.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After commit f84bb1ea ("net: fix IFF_NO_QUEUE for drivers using
alloc_netdev"), default qdisc was changed to noqueue because
tuntap does not set tx_queue_len during .setup(). This patch restores
default qdisc by setting tx_queue_len in tun_setup().

Fixes: f84bb1ea ("net: fix IFF_NO_QUEUE for drivers using alloc_netdev")
Cc: Phil Sutter <phil@nwl.cc>
Signed-off-by: NJason Wang <jasowang@redhat.com>
Acked-by: NMichael S. Tsirkin <mst@redhat.com>
Acked-by: NPhil Sutter <phil@nwl.cc>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix copy&paste error and state the name of SBPM register correctly.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Same field, same values, so share the same enum.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of that, pass mlxsw_core and use a helper to get driver priv
from driver code. Looks much cleaner that way.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of passing around driver priv, pass struct mlxsw_core *
directly.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove devlink port reg/unreg from spectrum and switchx2 code and rather
do the common work in core. That also ensures code separation where
devlink is only used in core.c.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since much of the required changes have already been made for
changing MTU at runtime let's use it for ring size changes as
well.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Soon ring resize will call this functions with values
different than the current configuration we need to
explicitly pass the ring count as parameter.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When changing MTU on running device first allocate new rings
and buffers and once it succeeds proceed with changing MTU.

Allocation of new rings is not really necessary for this
operation - it's done to keep the code simple and because
size of the extra ring memory is quite small compared to
the size of buffers.

Operation can still fail midway through if FW communication
times out.  In that case we retry with old MTU (rings).
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Free list buffer size needs to be propagated to few functions
as a parameter and added to struct nfp_net_rx_ring since soon
some of the functions will be reused to manage rings with
buffers of size different than nn->fl_bufsz.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

FW reconfiguration in .ndo_open()/.ndo_stop() should reset/
restore queue state.  Since we need IRQs to be disabled when
filling rings on RX path we have to move disable_irq() from
.ndo_open() all the way up to IRQ allocation.

nfp_net_start_vec() becomes trivial now so it's inlined.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Divide .ndo_open() and .ndo_stop() into logical, callable
chunks.  No functional changes.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

nfp_net_[rt]x_ring_{alloc,free} should only allocate or free
ring resources without touching the device.  Move setting
parameters in the BAR to separate functions.  This will make
it possible to reuse alloc/free functions to allocate new
rings while the device is running.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We want the .ndo_open() to have following structure:
 - allocate resources;
 - configure HW/FW;
 - enable the device from stack perspective.
Therefore filling RX rings needs to be moved to the beginning
of .ndo_open().
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Separate allocation of buffers from giving them to FW,
thanks to this it will be possible to move allocation
earlier on .ndo_open() path and reuse buffers during
runtime reconfiguration.

Similar to TX side clean up the spill of functionality
from flush to freeing the ring.  Unlike on TX side,
RX ring reset does not free buffers from the ring.
Ring reset means only that FW pointers are zeroed and
buffers on the ring must be placed in [0, cnt - 1)
positions.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since we never used flush without freeing the ring later
the functionality of the two operations is mixed.
Rename flush to ring reset and move there all the things
which have to be done after FW ring state is cleared.
While at it do some clean-ups.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To be able to switch rings more easily on config changes
allocate them dynamically, separately from nfp_net structure.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

nfp_net_[rt]x_ring_init functions used to be called from probe
path only and some of their functionality was spilled to the
call site.  In order to reuse them for ring reconfiguration
we need them to do all the init.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

nfp_net_{alloc|free}_rings contained strange mix of allocations
and vector initialization.  Remove it, declare vector init as
a separate function and handle allocations explicitly.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We need to be able to disable the link state interrupt when
the device is brought down.  We used to just free the IRQ
at the beginning of .ndo_stop().  As we now move towards
more ordered .ndo_open()/.ndo_stop() paths LSC allocation
should be placed in the "allocate resource" section.

Since the IRQ can't be freed early in .ndo_stop(), it is
disabled instead.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When calculating the RX buffer length we need to account
for up to 2 VLAN tags.  Rounding up to 1k is an relic of
a distant past and can be removed.  While at it also remove
trivial print statement.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit 0fd10721.

That patch causes the ib_srpt driver to crash as soon as the first SCSI
command is received:

  kernel BUG at drivers/infiniband/ulp/srpt/ib_srpt.c:1439!
  invalid opcode: 0000 [#1] SMP
  Workqueue: target_completion target_complete_ok_work [target_core_mod]
  RIP: srpt_queue_response+0x437/0x4a0 [ib_srpt]
  Call Trace:
    srpt_queue_data_in+0x9/0x10 [ib_srpt]
    target_complete_ok_work+0x152/0x2b0 [target_core_mod]
    process_one_work+0x197/0x480
    worker_thread+0x49/0x490
    kthread+0xea/0x100
    ret_from_fork+0x22/0x40

Aside from the crash, the shortcomings of that patch are as follows:

 - It makes the ib_srpt driver use I/O contexts allocated by
   transport_alloc_session_tags() but it does not initialize these I/O
   contexts properly.  All the initializations performed by
   srpt_alloc_ioctx() are skipped.

 - It swaps the order of the send ioctx allocation and the transition to
   RTR mode which is wrong.

 - The amount of memory that is needed for I/O contexts is doubled.

 - srpt_rdma_ch.free_list is no longer used but is not removed.
Signed-off-by: NBart Van Assche <bart.vanassche@sandisk.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Update ixgbe version number.
Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>