Merge tag 'tegra-for-4.11-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/dt

ARM: tegra: Device tree changes for v4.11-rc1

This contains a set of patches that add hardware compatibility for newer
revisions of the Toradex Apalis TK1. Also included is a fix to the PAZ00
that stabilizes panel initialization on boot as well as a patch to add
card detection for the µSD card slot on TrimSlice.

To round things off there are a couple of fixes and changes to the Nyan
device tree files to fix the battery charger, add compatibility with new
revisions of Nyan Blaze and Nyan Big, as well as properly support the
TPM.

* tag 'tegra-for-4.11-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
  ARM: tegra: nyan-blaze: Proper pinmux for TPM I2C
  ARM: tegra: nyan-big: Proper pinmux for TPM I2C
  ARM: tegra: nyan-blaze: Include compatible revisions for proper detection
  ARM: tegra: nyan-big: Include compatible revisions for proper detection
  ARM: tegra: nyan: Use external control for bq24735 charger
  ARM: tegra: nyan: Use proper IRQ type definitions
  ARM: dts: tegra: Fix missing card detection in Trimslice µSD card slot
  ARM: tegra: paz00: Mark panel regulator as enabled on boot
  ARM: tegra: apalis-tk1: Update compatibility comment
  ARM: tegra: apalis-tk1: Fix SD card detect on v1.1 HW
  ARM: tegra: apalis-tk1: Adjust pin muxing for v1.1 HW
  ARM: tegra: apalis-tk1: Optional DisplayPort hot-plug detect
  ARM: tegra: apalis-tk1: Pull-up temperature alert
Signed-off-by: NOlof Johansson <olof@lixom.net>

Merge tag 'at91-ab-4.11-dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux into next/dt

DT for 4.11 #2:

 - Enable the DMA on sama5d2 and sama5d4 xplained to fix an issue seen by
 kernelci

* tag 'at91-ab-4.11-dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
  ARM: dts: at91: Enable DMA on sama5d2_xplained console
  ARM: dts: at91: Enable DMA on sama5d4_xplained console
Signed-off-by: NOlof Johansson <olof@lixom.net>

Merge tag 'renesas-dt2-for-v4.11' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt

Second Round of Renesas ARM Based SoC DT Updates for v4.11

Enhancements:
- Add power-domains to mmcif on r7s72100 SoC
- Add OSTM to rskrza1/r7s72100
- Link ARM GIC to clock and clock domain on r8a774[35] SoCs

Clean-up:
- Correct SATA device status on r8a7779/marzen

* tag 'renesas-dt2-for-v4.11' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
  ARM: dts: r7s72100: add power-domains to mmcif
  ARM: dts: rskrza1: add ostm DT support
  ARM: dts: r7s72100: add ostm to device tree
  ARM: dts: r7s72100: add ostm clock to device tree
  ARM: dts: r8a7745: Link ARM GIC to clock and clock domain
  ARM: dts: r8a7743: Link ARM GIC to clock and clock domain
  ARM: dts: r8a7779, marzen: Fix sata device status
Signed-off-by: NOlof Johansson <olof@lixom.net>

Lots of updates for mt2701:
Rearrange the dt nodes and fix unit address for pincontroler
Add nodes for:
- clock controller subsystems
- scpsys controller
- iommu and smi
- spi
- nand
- auxadc
- thermal controller and zones

Email address updated for mt7623 devicetree files.

* tag 'v4.10-next-dts32' of https://github.com/mbgg/linux-mediatek:
  arm: dts: mt2701: Add thermal device node.
  arm: dts: mt2701: Add auxadc device node.
  arm: dts: mt2701: Add nand device node
  arm: dts: mt2701: Add spi device node
  ARM: dts: mt2701: add iommu/smi dtsi node for mt2701
  ARM: dts: mediatek: update my email address
  arm: dts: mt2701: Add power domain controller device node
  arm: dts: mt2701: Add subsystem clock controller device nodes
  arm: dts: mt2701: Sort DT nodes by register address
Signed-off-by: NOlof Johansson <olof@lixom.net>

Merge tag 'omap-for-v4.11/dt-signed-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt

Device tree changes for omaps for v4.11 merge window. These
changes add earlycon stdout-path propety for the SoCs so far
tested with it. The other changes are addition of BeagleBone
green and making WLAN work on BeagleBone black wireless and
green wireless. The rest of the changes are the usual enabling
features on various devices:

- Enable devices on am335x-sl50
- Changes to dra7-evm boards to enable enable irqs for dp83867
  eth phys, add pinmux configuration for mmc, remov erratum
  i869 pinmux configurations, disable NAND support because of
  pin conflict, add pcf8575 used for lcd
- Remove NAND partition table for omap3-igep
- Configure USB Ethernet MAC from device tree for beagleboard
  xm, pandaboard, omap5-uevm and igepv5
- Configure am335x-chilisom to wake from RTC-only state
- Update Nanobone for external FRAM chip
- Clean up n900 dts
- Update am335x-phycore and am335x-wega for various devices
- Changes for am57xx-beagle-x15 to implement rgmii2 errata

* tag 'omap-for-v4.11/dt-signed-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (35 commits)
  ARM: dts: dra72/1-evm: add pcf8575 used for lcd
  ARM: dts: dra7xx: Add stdout-path property
  ARM: dts: am57xx: Add stdout-path property
  ARM: dts: am43xx: Add stdout-path property
  ARM: dts: am33xx: Add stdout-path property
  ARM: dts: am335x-sl50: Enable the Ambient Light Sensor.
  ARM: dts: am335x-sl50: Enable the MCP23017 GPIO Expander.
  ARM: dts: am335x-sl50: Enable BQ32000 Real Time Clock.
  ARM: dts: am335x-sl50: Enable SPI0 interface and Flash Memory.
  ARM: dts: am335x-sl50: Enable UART1.
  ARM: dts: am335x-sl50: Remove I2C1 node.
  ARM: dts: omap3-igep: Remove NAND partition table
  ARM: dts: am57xx-beagle-x15: implement errata "Ethernet RGMII2 Limited to 10/100 Mbps"
  ARM: dts: am335x-phycore-som: Remove partition tables
  ARM: dts: dra72-evm-revc: enable irqs for dp83867 eth phys
  ARM: dts: Configure BeagleBone peripheral USB VBUS irq
  ARM: dts: omap5-igep0050: Allow bootloader to configure USB Ethernet MAC
  ARM: dts: omap5-uevm: Allow bootloader to configure USB Ethernet MAC
  ARM: dts: pandaboard: Allow bootloader to configure USB Ethernet MAC
  ARM: omap3: beagleboard-xm: dt: Add ethernet to the device tree
  ...
Signed-off-by: NOlof Johansson <olof@lixom.net>

Merge tag 'davinci-for-v4.11/dt' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into next/dt

Device tree updates for DaVinci DA850

* GPIO keys on DA850 LCDK
* LCDC display on DA850 LCDK
* USB OHCI on DA850 LCDK
* VPIF (video input) on DA850 LCDK
* Add a DA8xx specific compatible for UARTs
* Introduce support for Lego Mindstorms EV3

* tag 'davinci-for-v4.11/dt' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
  ARM: dts: Add LEGO MINDSTORMS EV3 dts
  dt-bindings: add "microchip,24c128" compatible string
  dt-bindings: Add LEGO MINDSTORMS EV3 compatible specification
  dt-bindings: Add vendor prefix for LEGO
  ARM: dts: da850: Add ti,da830-uart compatible for serial ports
  ARM: dts: davinci: da850-lcdk: enable VPIF
  ARM: dts: davinci: da850-evm: enable VPIF
  ARM: dts: davinci: da850: VPIF: add node and muxing
  ARM: dts: da850-lcdk: Enable ohci for omapl138 lcdk
  ARM: dts: da850: Add usb device node
  ARM: dts: da850: specify the maximum pixel clock rate for tilcdc
  ARM: dts: da850-lcdk: add the vga-bridge node
  ARM: dts: da850: rename the display node label
  ARM: dts: da850-lcdk: add gpio-keys
Signed-off-by: NOlof Johansson <olof@lixom.net>

Merge tag 'qcom-dts-for-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux into next/dt

Qualcomm Device Tree Changes for v4.11

* Add Coresight components for APQ8064
* Fixup PM8058 nodes
* Add APQ8060 gyro and accel support
* Enable SD600 HDMI support
* Add RIVA supprort for Sony Yuga and SD600
* Add PM8821 support
* Add MSM8974 ADSP, USB gadget, SMD, and SMP2P support
* Fix IPQ8064 clock frequencies

* tag 'qcom-dts-for-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux:
  ARM: dts: qcom: Add apq8064 CoreSight components
  ARM: dts: Add gyro and accel to APQ8060 Dragonboard
  ARM: dts: reference PM8058 as IRQ parent
  ARM: dts: rename MSM8660/APQ8060 pmicintc to pm8058
  ARM: dts: sd-600eval: enable 1.8v regulator on LS expansion
  ARM: dts: sd-600eval: add hdmi support
  ARM: dts: move hdmi pinctrl out of board file.
  ARM: dts: qcom: sd600eval: Enable riva-pil
  ARM: dts: qcom: sd600-eval: pm8921_s2 regulator properties
  ARM: dts: qcom: apq8064-sony-yuga: Enable riva-pil
  ARM: dts: qcom: apq8064: Add riva-pil node
  ARM: dts: apq8064: add support to pm8821
  arm: dts: qcom: Fix ipq board clock rates
  ARM: dts: msm8974: Remove "unused" reserved region
  ARM: dts: msm8974: Add ADSP PIL node
  ARM: dts: msm8974: Add ADSP smp2p and smd nodes
  ARM: dts: qcom: msm8974: Add USB gadget nodes
Signed-off-by: NOlof Johansson <olof@lixom.net>

Merge tag 'uniphier-dt-v4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier into next/dt

UniPhier ARM SoC DT updates for v4.11

- Add eMMC, SD pin-mux nodes

* tag 'uniphier-dt-v4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier:
  ARM: dts: uniphier: add SD pin-mux node
  ARM: dts: uniphier: add eMMC pin-mux node
Signed-off-by: NOlof Johansson <olof@lixom.net>

Merge tag 'keystone_dts_for_4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone into next/dt

ARM: Keystone DTS update for 4.11

Brief:
	- MSM RAM node support for the Keystone 2 SOCs.
	- PSC node & reset controller node support for keystone 2 SOCs.
	- da830 UART node support.

* tag 'keystone_dts_for_4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone:
  ARM: dts: keystone-k2e: Add PSC reset controller node
  ARM: dts: keystone-k2l: Add PSC reset controller node
  ARM: dts: keystone-k2hk: Add PSC reset controller node
  ARM: dts: keystone: Add PSC node
  ARM: keystone: dts: fix netcp clocks and add names
  ARM: dts: keystone-k2g: Reserve MSM RAM for boot monitor
  ARM: dts: keystone-k2e: Reserve MSM RAM for boot monitor
  ARM: dts: keystone-k2l: Reserve MSM RAM for boot monitor
  ARM: dts: keystone-k2hk: Reserve MSM RAM for boot monitor
  ARM: dts: keystone-k2g: Add MSM RAM node
  ARM: dts: keystone-k2e: Add MSM RAM node
  ARM: dts: keystone-k2l: Add MSM RAM node
  ARM: dts: keystone-k2hk: Add MSM RAM node
  ARM: dts: keystone: Add "ti,da830-uart" compatible string
Signed-off-by: NOlof Johansson <olof@lixom.net>

Merge tag 'v4.11-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt

Bit of cleanup for the cortex-a9 uarts to have that soc-specific
spare-compatible as all others have, conversion to gpio constants
and addition of rk3288 qos nodes that need to be saved before a
power-domain gets turned off.

* tag 'v4.11-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
  ARM: dts: rockchip: add soc-specific uart compatibles for rk3066/rk3188
  ARM: dts: rockchip: use pin constants to describe gpios
  ARM: dts: rockchip: add qos node for rk3288
Signed-off-by: NOlof Johansson <olof@lixom.net>

This corrects the pinmux for accessing the TPM over the I2C line. Thus,
it allows correctly probing the module, that previously failed with I2C
errors.
Signed-off-by: NJerome Coste <jerome.coste@etu.utc.fr>
Signed-off-by: NPaul Kocialkowski <contact@paulk.fr>
Signed-off-by: NThierry Reding <treding@nvidia.com>

This corrects the pinmux for accessing the TPM over the I2C line. Thus,
it allows correctly probing the module, that previously failed with I2C
errors.
Signed-off-by: NPaul Kocialkowski <contact@paulk.fr>
Signed-off-by: NThierry Reding <treding@nvidia.com>

Depthcharge (the payload used with cros devices) will attempt to detect
boards using their revision. This includes all the known revisions for
the nyan-blaze board so that the dtb can be selected preferably.

Defining compatibly revisions allows depthcharge to select the kernel
via the revision it detects instead of using the default kernel. This
allows having a FIT image with multiple kernels for multiple devices.
Signed-off-by: NPaul Kocialkowski <contact@paulk.fr>
Signed-off-by: NThierry Reding <treding@nvidia.com>

Depthcharge (the payload used with cros devices) will attempt to detect
boards using their revision. This includes all the known revisions for
the nyan-big board so that the dtb can be selected preferably.

Defining compatibly revisions allows depthcharge to select the kernel
via the revision it detects instead of using the default kernel. This
allows having a FIT image with multiple kernels for multiple devices.
Signed-off-by: NPaul Kocialkowski <contact@paulk.fr>
Signed-off-by: NThierry Reding <treding@nvidia.com>

Nyan boards come with an embedded controller that controls when to
enable and disable the charge. Thus, it should not be left up to the
kernel to handle that.

Using the ti,external-control property allows specifying this use-case.
Signed-off-by: NPaul Kocialkowski <contact@paulk.fr>
Signed-off-by: NThierry Reding <treding@nvidia.com>

This switches a few interrupt definitions that were using
GPIO_ACTIVE_HIGH as IRQ type, which is invalid.

This is mostly a cosmetic change, that doesn't affect any driver.
Signed-off-by: NPaul Kocialkowski <contact@paulk.fr>
Signed-off-by: NThierry Reding <treding@nvidia.com>

Signed-off-by: NChris Brandt <chris.brandt@renesas.com>
Reported-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Acked-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Card insertion and removal currently goes undetected. AFAIK there's no
way to generate interrupts on card changes in this slot, so use polling.
Signed-off-by: NRask Ingemann Lambertsen <rask@formelder.dk>
Signed-off-by: NThierry Reding <treding@nvidia.com>

Current U-Boot enables the display already. Marking the regulator as
enabled on boot fixes sporadic panel initialization failures.
Signed-off-by: NMarc Dietrich <marvin24@gmx.de>
Tested-by: NMisha Komarovskiy <zombah@gmail.com>
Signed-off-by: NThierry Reding <treding@nvidia.com>

Now with the new V1.1A HW card detect being implemented update resp.
compatibility information.
Signed-off-by: NMarcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: NThierry Reding <treding@nvidia.com>

Add SD card detect SD1_CD# applicable for V1.1 modules using GPIO_PV2.
Signed-off-by: NMarcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: NThierry Reding <treding@nvidia.com>

Configure Apalis MMC1 D6 GPIO on SDMMC3_CLK_LB_IN as reserved function
without any pull-up/down.

Configure GPIO_PV2 as SD1_CD# according to latest V1.1 HW.

Leave SDMMC3_CLK_LB_OUT muxed as SDMMC3 with output driver enabled aka
not tristated and input driver enabled as well as it features some
magic properties even though the external loopback is disabled and the
internal loopback used as per SDMMC_VENDOR_MISC_CNTRL_0 register's
SDMMC_SPARE1 bits being set to 0xfffd according to the TRM! This pin is
now a not-connect on V1.1 HW in order to avoid any interference.
Signed-off-by: NMarcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: NThierry Reding <treding@nvidia.com>

Configure DP_HPD_PFF0 pin as optional DisplayPort hot-plug detect.
Signed-off-by: NMarcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: NThierry Reding <treding@nvidia.com>

Pull-up GPIO_PI6 connected to TMP451's ALERT#/THERM2#.
Signed-off-by: NMarcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: NThierry Reding <treding@nvidia.com>

Signed-off-by: NChris Brandt <chris.brandt@renesas.com>
Reviewed-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Signed-off-by: NChris Brandt <chris.brandt@renesas.com>
Reviewed-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Signed-off-by: NChris Brandt <chris.brandt@renesas.com>
Reviewed-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Add thermal controller device nodes for MT2701.
Signed-off-by: NDawei Chien <dawei.chien@mediatek.com>
Signed-off-by: NErin Lo <erin.lo@mediatek.com>
Signed-off-by: NMatthias Brugger <matthias.bgg@gmail.com>

DRA72 and DRA718 EVM boards has a pcf8575 gpio expander
which is used for the LCD/LEDs and USB vbus detection.
Add the node for the pcf8575.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Link the ARM GIC to the INTC-SYS module clock, and add it to the SYSC
"always-on" PM Domain, so it can be power managed using that clock.

Note that currently the GIC-400 driver doesn't support module clocks nor
Runtime PM, so this must be handled as a critical clock.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Link the ARM GIC to the INTC-SYS module clock, and add it to the SYSC
"always-on" PM Domain, so it can be power managed using that clock.

Note that currently the GIC-400 driver doesn't support module clocks nor
Runtime PM, so this must be handled as a critical clock.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Enable DMA on uart1 to get a more reliable console.

Cc: stable <stable@vger.kernel.org> #v4.3+
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

The Pro4 SoC has 2 slots of SD controllers, so 2 pin-mux nodes
(SD and SD1) are needed.  The other SoCs have only 1 SD slot.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>

All UniPhier SoCs support an eMMC controller.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>

Add stdout-path property in /chosen node so that earlycon can be
used by just adding earlycon in bootargs.
Tested-by: NVignesh R <vigneshr@ti.com>
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add stdout-path property in /chosen node so that earlycon can be
used by just adding earlycon in bootargs.
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add stdout-path property in /chosen node so that earlycon can be
used by just adding earlycon in bootargs.
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add stdout-path property in /chosen node so that earlycon can be
used by just adding earlycon in bootargs.
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add support for the ISL29023 ALS connected via the I2C bus.
Signed-off-by: NEnric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add support for the 16-Bit I/O Expander connected via the I2C bus.
Signed-off-by: NEnric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>