This patch adds a driver for a harddrive attached to PXA address and data bus.
Unlike pata_platform, this driver allows usage of PXA DMA controller, making the
transmission speed 3x higher.
Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>
Acked-by: NJeff Garzik <jgarzik@redhat.com>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Reported-by: NAndrea Adami <andrea.adami@gmail.com>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Since commit a48c24a6, the
camera is not working anymore.

After the v4l2 migration, the mt9m111 camera board
information was not passed to the i2c layer anymore, but
stored for future use of v4l2 (through soc_camera).

Because mioa701_i2c_devices[] was tagged as "__initdata",
and because after the v4l2 migration, the new structure
"iclink" references it, the mt9m111 driver is not probed
anymore, as part of "iclink" is not valid (discarded after
kernel init).

Although there is not compilation error, nor runtime oops,
this patch restores a working camera on the mioa701 board.
Signed-off-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Acked-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

This patch fixes flash layout to it's final version. Also, I fixed the
authorship information of this file as it's been totally reworked since Ken
released his last version.
Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

This patch registers the WM8750 codec on a proper place on the SPITZ machine
after the WM8750 driver was converted to new API.
Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

The C99 specification states in section 6.11.5:

The placement of a storage-class specifier other than at the beginning
of the declaration specifiers in a declaration is an obsolescent
feature.
Signed-off-by: NTobias Klauser <tklauser@distanz.ch>
Acked-by: NMarek Vasut <marek.vasut@gmail.com>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

delay_detect in HZ is confusing, convert it to be millisecond based. And
thus remove those unnecessary call to msecs_to_jiffies() at runtime for
this field. Other constants are converted assuming HZ == 100, which are
basically true for those platforms.

The assignment in csb726.c was incorrect, and is fixed in this patch as
a result.
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>
Acked-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Acked-by: NMarc Zyngier <maz@misterjones.org>
Acked-by: NMarek Vasut <marek.vasut@gmail.com>
Acked-by: NMike Rapoport <mike@compulab.co.il>
Acked-by: NDaniel Mack <daniel@caiaq.de>

This patch removes write to UP2OCR[DMSTATE] (ex-UP2OCR_DPPUBE) which is invalid
on PXA270C5 and later.
Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

The touchscreen GPIO IRQ was used as a magic number. Define it properly in the
board header file. This is a simple cleanup patch.
Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

This patch adds support for the on-board IDE channel. I tested this with a CDROM
connected over 2.5-3.5 IDE reduction with external power supplied to the CDROM.
This was not tested with the Voipac 270-HDD-000 (official Voipac HDD module),
but I expect no problems.
Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

This adds support for the UCB1400 touchscreen found in the VPAC270 device.
Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

NOTE:
I wasn't able to get it running without reseting the HXOE (so it's there based
on my tests with the hardware). I'll have to investigate it properly when I have
more time.
Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>
Reviewed-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

PCMCIA support for Voipac PXA270
Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

This patch adds basic support for the Voipac PXA270 SBC.
The device consists of the following hardware:
- PXA270 @ 520 MHz
- 256MB RAM (sparsemem, 2*128MB regions)
- 64MB NOR flash
- 640x480 LCD
- Ports: 2xUHC, 1xUDC, 1xPCMCIA, VGA, FFUART, 2xPS2, Speaker, MIC
Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

This patch adds support for the Zipit Z2. The parts missing from this
patch are the battery support, SPI driver for the LCD and support for
the Silicon Serial ID chip.
Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

CM-X300 bootloader passes DRAM configuration information in ATAGS,
however, the first memory bank is reported at actual physical address 0x8000000.
Use the configuration information supplied by the bootloader and
cope with the necessity to have PHYS_ADDR=0xa0000000.
Signed-off-by: NIgor Grinberg <grinberg@compulab.co.il>
Signed-off-by: NMike Rapoport <mike@compulab.co.il>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Signed-off-by: NIgor Grinberg <grinberg@compulab.co.il>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Signed-off-by: NIgor Grinberg <grinberg@compulab.co.il>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Signed-off-by: NIgor Grinberg <grinberg@compulab.co.il>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Signed-off-by: NIgor Grinberg <grinberg@compulab.co.il>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Tosa is now able to use generic matrix keypad driver instead of the deprecated
tosakbd.c, where CONFIG_KEYBOARD_TOSA_USE_EXT_KEYCODES is still useful.  Move
it to mach/Kconfig.
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

REVISIT: change to GPIO18 is ugly, need to make sure whether that's
really necessary - GPIO18_RDY as an VLIO input signal - we don't
normally need to do such kind of trick during low power mode.
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Some pins are expected to keep their last level during suspend, and
introduce MFP_LPM_KEEP_OUTPUT for this.
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

PXA_SSP is actually used by drivers like drivers/spi/pxa2xx_spi.c and
sound/soc/pxa/pxa-ssp.c, not by boards. Remove those incorrect 'select'
from Kconfig and make SOC_PXA_SSP to select.
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Signed-off-by: NHaojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

No need to separate them as they should be together from the begining.
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

The previous definitions of SSCR0_SCR and SSCR0_SerClkDiv() prevented
them being used simultaneously when supporting multiple PXA SoCs, esp.
in drivers/spi/pxa2xx_spi.c, make them correct.

The change from SSCR0_SerClkDiv(2) to SSCR0_SCR(2), will make the result
a little bit different in pxa2xx_spi_probe(), however, since that's only
used as a default initialization value, it's acceptable.
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

The only use of corgi_ssp.c is corgi_ts.c, which is now deprecated
and removed. Remove corgi_ssp.c and corgi_lcd.c and their relevant
function declarations and data structures.
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Pavel Machek <pavel@ucw.cz>

The use of mfp_cfg_t causes build errors without including <mach/mfp.h>.

CC: stable@kernel.org
CC: Daniel Mack <daniel@caiaq.de>
Signed-off-by: NJakob Viketoft <jakob.viketoft@bitsim.com>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

On/Off contains slash in the name, which causes warning during boot.
Signed-off-by: NPavel Machek <pavel@ucw.cz>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>