This patch is meant to fix a memory leak found via code review for FCOE.
Specifically on DDP flows the SKBs were being dropped without being
recycled, freed, or given to the stack.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Fix pointer to setup_link for 82599.

This resolves some link issues when advertising modes unsupported
by the link partner.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The way __ixgbe_notify_dca() was currently set up it would not be
possible to add a requester. Both cases of the IXGBE_FLAG_DCA_ENABLED
bit being on and off would lead to the function exiting for a
DCA_PROVIDER_ADD.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

after review of all intel drivers, found several instances where
drivers had the incorrect pattern of:
memory mapped write();
delay();

which should always be:
memory mapped write();
write flush(); /* aka memory mapped read */
delay();

explanation:
The reason for including the flush is that writes can be held
(posted) in PCI/PCIe bridges, but the read always has to complete
synchronously and therefore has to flush all pending writes to a
device.  If a write is held and followed by a delay, the delay
means nothing because the write may not have reached hardware
(maybe even not until the next read)
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Private rx_csum flags are now duplicate of netdev->features &
NETIF_F_RXCSUM.  We remove those duplicates and now use the net_device_ops
ndo_set_features.  This was based on the original patch submitted by
Michal Miroslaw <mirq-linux@rere.qmqm.pl>.  I also removed the special
case not requiring a reset for X540 hardware.  It is needed just as it is
in 82599 hardware.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Cc:  Michal Miroslaw <mirq-linux@rere.qmqm.pl>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Martin Wilck <martin.wilck@ts.fujitsu.com> reported that systems using
the ixgbe-driver that were capable of WoL were rebooting almost as soon
as they were shut down.  This is because the default WoL settings
enabled magic packet, broadcast, unicast, and multicast.

Other Intel devices seem to use the stored eeprom value for initial WoL
capabilities.  The 82578DM (e1000e) and 82576 (igb) the devices I looked
at had only the magic packet enabled in the eeprom, so that seems
appropriate on ixgbe-based devices as well.  I set the WoL options on my
82578DM to be the same default as the ixgbe devices (umbg) and saw the
same as Martin -- almost as soon as my box shutdown, it booted again.

This patch changes the default to only be the magic packet.  This is the
same as the default for most Intel and non-Intel hardware currently
upstream.
Signed-off-by: NAndy Gospodarek <andy@greyhouse.net>
CC: Martin Wilck <martin.wilck@ts.fujitsu.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change is meant to address possible race conditions from the status
and error bits on the RX descriptors being re-read by multiple functions in
the RX cleanup path.  To resolve this I have added code that will pass the
staterr value to those functions.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change moves work_limit, total_packets, and total_bytes into the ring
container struct of the q_vector.  The advantage of this is that it should
reduce the size of memory used in the event of multiple rings being
assigned to a single q_vector.  In addition it should help to reduce the
total workload for calculating itr since now total_packets and total_bytes
will be the total work done of the interrupt instead of for the ring.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds support for a ring container structure to be used within
the q_vector.  The basic idea is to provide a means of separating the RX
and TX rings while maintaining a common structure for their containment.
The advantage to this is that later we should be able to pass this
structure to the update_itr functions without needing to pass individual
rings.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The ixgbe_maybe_stop_tx function is only a few lines long and is called
multiple times through the xmit hotpath.  In order to streamline things it
makes sense to just inline it.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change is meant to update ATR so that it will use the recorded RX
queue instead of the CPU in the case of routing.  This change is meant to
help ixgbe default behavior to more closely match that of the kernel.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This fix makes it so that the fdir_perfect_lock is initialized in all
cases.  This is necessary as the fdir_filter_exit routine will always
attempt to take the lock before inspecting the filter table.
Reported-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Implement DCB ops dcb_ieee_del() and set FCoE to the default
priority when no priority exists.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The fcoe.tc field is no longer used so remove it. After
the field is removed there is no need to keep fcoe_setapp()
around so remove it as well. And finally we can get rid
of some DCB #ifdef's in the fcoe code.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Commit,

commit c8ca76eb
Author: John Fastabend <john.r.fastabend@intel.com>
Date:   Sat Mar 12 03:50:53 2011 +0000

    ixgbe: DCB, further cleanups to app configuration

Removed the getapp() routines from ixgbe because they are no
longer needed. It also allowed the set hardware routines to
use both IEEE 802.1Qaz app types and CEE app types. This
added code to do bit shifting in the IEEE case.

This patch reverts the checks and handles the IEEE case
from the setapp entry point. I prefer this because it
keeps the two paths from having to be aware of the DCB
mode. This resolves a bug where I missed setting the
selector bit in the IEEE spec value and left it in the
CEE value. Now that they are separate routines these types
of errors should not occur.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

There is a need to configure MMW_SIZE in register RTTBCNRM with a correct
value (0x4 for non jumbo frames and 0x14 for jumbo frames support).
For 82599 the value is 0x4 and for X540 the value is 0x14.
Signed-off-by: NLior Levy <lior.levy@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch updates the current methods used for determining if we have
enough space to transmit a given skb.  The current method is quite wasteful
as it has us go through and determine how each page is going to be broken
up.  That only needs to be done if pages are larger than our maximum data
per TXD.  As such I have wrapped that in a page size check.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

There is a significant amount of shared functionality between the checksum
and TSO offload configuration that is shared in regards to how they setup
the context descriptors.  Since so much of the functionality is shared it
makes sense to move the shared functionality into a single function and
just call that function from the two context descriptor specific routines.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change updates all values dealing with count, next_to_use, and
next_to_clean so that they stay u16 values.  The advantage of this is that
there is no re-casting of type during the propagation through the stack.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change is a minor cleanup that converts the IXGBE_DESC_UNUSED macro
into a static inline function just for the case of the code being a bit
cleaner.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change makes it so that we pass the adapter struct instead of the
netdev for most of the basic interrupts that are not associated with
q_vectors.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Update the ixgbe driver version string to better match the Source Driver
with similar device support.  Likewise update to the current LAD Linux
versioning scheme.
Signed-of-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NEvan Swanson <evan.swanson@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change fixes the fact that we would trigger a null pointer dereference
or specify the wrong ring if the rings were restored.  This change makes
certain that the DROP queue is a static value, and all other rings are
based on the ring offsets for the PF.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Disabling Rx checksumming leads to performance degradation due to
RSC causing packets to have incorrect checksums.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NEvan Swanson <evan.swanson@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Move reset code into a separate function to allow for reuse in other
parts of the code.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Move setting RSC into a separate function to allow for reuse in other
parts of the code.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change is meant to allow for nfc to insert and remove filters in order
to test the ethtool interface which includes it's own rules manager.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This code adds support for displaying the filters that were added via the
nfc interface.  This is primarily to test the interface for now, but I am
also looking into the feasibility of moving all of the ntuple filter code
in ixgbe over to the nfc interface since it seems to be better implemented.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change adds basic support for the obtaining of RSS ring counts.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change is meant to update the internal framework of ixgbe so that
perfect filters can be stored and tracked via software.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

I am removing the requirement that Ntuple filters have the same
number of queues and requirements as ATR.  As a result this change will
make it so that all the Ntuple flag does is disable ATR for now.

This change fixes an issue in which we were incorrectly re-enabling ATR
when we exited perfect filter mode.  This was due to the fact that the
logic assumed RSS and DCB were mutually exclusive which is no longer the
case.

To correct this we just need to add a check to guarantee DCB is disabled
before re-enabling ATR.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Due to numerous issues in ntuple filters it has been decided to move the
interface over to the network flow classification interface.  As a first
step to achieving this I first need to remove the old ntuple interface.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently single PCI pool used across all CPUs and that
doesn't scales up as number of CPU increases, so this
patch adds per CPU PCI pool to setup udl and that aligns
well from FCoE stack as that already has per CPU exch locking.

Adds per CPU PCI alloc setup and free in
ixgbe_fcoe_ddp_pools_alloc and ixgbe_fcoe_ddp_pools_free,
use CPU specific pool during DDP setup.

Re-arranged ixgbe_fcoe struct to have fewer holes
along with adding pools ptr using pahole.
Signed-off-by: NVasu Dev <vasu.dev@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds support for Dell CEM (Comprehensive Embedded Management)).
This consists of informing the management firmware of the driver version
during probe on 82599 and X540 HW.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NEvan Swanson <evan.swanson@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The ixgbe_dcb_txq_to_tc() routine was used to map TX rings to
a DCB traffic class. Now that a tx_ring has a DCB traffic class
associated with it this routine is no longer needed.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Now flow directors perfect filters features can coexist with DCB.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This bit mask is wrong DCBX_HOST is always set. It was missed up
until now because lldpad reprograms the device on a link
event. However this is still wrong and it is best not to be
mis-configured for some time immediately following ixgbe_up().
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Setup RSS redirection table to be compatible with multiple packet
buffers. Currently, this works on 82599 devices because the RSS
redirection index is masked by the number of queues per packet
buffer.

This sets the cap on the RSS table to maxq.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The tx_idx and rx_idx values are swapped on 82598 devices
with DCB enabled.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>