This patch adds platform init/exit functions and modifications to support
suspend/resume for the Altera Cyclone 5 SOC Ethernet controller. The platform
exit function puts the controller into reset using the socfpga reset
controller driver. The platform init function sets up the Synopsys mac by
first making sure the Ethernet controller is held in reset, programming the
phy mode through external support logic, then deasserts reset through
the socfpga reset manager driver.
Signed-off-by: NVince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the event flow, we currently pass only a port number in the
void *data argument.  Rather than pass a pointer to the event handlers,
we should use an "unsigned long" parameter, and pass the port number
value directly.

In the future, if necessary for some events, we can use the unsigned long
parameter to pass a pointer.

Based on a patch by Eli Cohen <eli@mellanox.com>
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NEli Cohen <eli@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There were many places where parameters which should be u8/u16 were
integer type.

Additionally, in 2 places, a check for a non-null pointer was added
before dereferencing the pointer (this is actually a bug fix).
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NEli Cohen <eli@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In preparation for a new mlx5 device which is VPI (i.e., ports can be
either IB or ETH), move the pci device functionality from mlx5_ib
to mlx5_core.

This involves the following changes:
1. Move mlx5_core_dev struct out of mlx5_ib_dev. mlx5_core_dev
   is now an independent structure maintained by mlx5_core.
   mlx5_ib_dev now has a pointer to that struct.
   This requires changing a lot of places where the core_dev
   struct was accessed via mlx5_ib_dev (now, this needs to
   be a pointer dereference).
2. All PCI initializations are now done in mlx5_core. Thus,
   it is now mlx5_core which does pci_register_device (and not
   mlx5_ib, as was previously).
3. mlx5_ib now registers itself with mlx5_core as an "interface"
   driver. This is very similar to the mechanism employed for
   the mlx4 (ConnectX) driver. Once the HCA is initialized
   (by mlx5_core), it invokes the interface drivers to do
   their initializations.
4. There is a new event handler which the core registers:
   mlx5_core_event(). This event handler invokes the
   event handlers registered by the interfaces.

Based on a patch by Eli Cohen <eli@mellanox.com>
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NEli Cohen <eli@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This commit implements the ->ndo_do_ioctl() operation so that the
PHY-related ioctl() calls can work from userspace, which allows
applications like mii-tool or mii-diag to do their job.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This commit is similar to commit 4d12bc63 ("net: mvneta: fix
operation in 10 Mbit/s mode"), but this time for the mvpp2 driver. The
driver was properly taking into account the 1 Gbit/s and 100 Mbit/s
speeds, but not the 10 Mbit/s, which was handled as 100
Mbit/s. However, the MVPP2_GMAC_CONFIG_MII_SPEED bit in the
MVPP2_GMAC_AUTONEG_CONFIG register must remain cleared to allow 10
Mbit/s operation. This commit therefore fixes 10 Mbit/s operation.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

__iowrite64_copy() isn't quite the same as efx_memcpy_64(), but
it looks close enough:

- The length is in units of qwords not bytes
- It never byte-swaps, but that doesn't make a difference now as PIO
  is only enabled for x86_64
- It doesn't include any memory barriers, but that's OK as there is a
  barrier just before pushing the doorbell
- mlx4_en uses it for the same purpose

Compile-tested only.
Signed-off-by: NBen Hutchings <ben@decadent.org.uk>
Acked-by: NEdward Cree <ecree@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This driver explicitly clears a field that is unused and about to be
removed. Remove the initialization.

All fields in skb_shared_info before dataref are cleared in
__alloc_skb, so the removal is safe even while syststamp exists.
Signed-off-by: NWillem de Bruijn <willemb@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Hardware timestamps can be exposed to userspace in raw hardware format
(hwtstamp) as well as converted to system time (syststamp). The second
variant is deprecated and only implemented by this driver.

The preferred method of hardware timestamp generation is to combine
hwtstamp with a device PTP clock. Octeon has its own PTP library
that relies on a shared memory interface to the PTP clock device.
Signed-off-by: NWillem de Bruijn <willemb@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The sunvnet driver doesn't check whether or not a port is connected when
transmitting packets, which results in failures if a port fails to connect
(e.g., due to a version mismatch). The original code also assumes
unnecessarily that the first port is up and a switch, even though there is
a flag for switch ports.

This patch only matches a port if it is connected, and otherwise uses the
switch_port flag to send the packet to a switch port that is up.
Signed-off-by: NDavid L Stevens <david.stevens@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adding a function, and associated calls, to flush writes to (read) the LPIC
MAC register before entering the shutdown flow.  This fixes the problem
of the PHY never negotiating a 100M link (if both sides of the link support
EEE and 100M link) when Runtime PM is enabled.
Signed-off-by: NDave Ertman <david.m.ertman@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The process of shutting down the system causes a call to the close PM
callback.  The reset in close causes a loss of link, and the resultant
LSC interrupt causes the Runtime PM idle callback to be called.  The
check for link (while link is down) in the idle callback is wiping the
information about the EEE ability of the link partner.  The information is
still gone when the PHY is powered back up in the shutdown flow.  This
causes EEE in S5 to fail when Runtime PM is active.

Save the link partner's EEE ability in the idle callback so that a Runtime
PM event will not cause a loss of this information.
Signed-off-by: NDave Ertman <david.m.ertman@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

On I217 and newer hardware, EEE is enabled in the PHY by the software
when link is up and disabled by the hardware when link is lost.

To enable EEE in Sx (When both ends of the link support, and are enabled
for, EEE and 100Mbps), we need to disable LPLU and configure the PHY to
automatically enable EEE when link is up, since there will be no software
to complete the task.

To configure this in the PHY, the Auto Enable LPI bit in the Low Power
Idle GPIO Control register must be set.  For normal operation in S0, this
bit must be cleared.
Signed-off-by: NDave Ertman <david.m.ertman@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Adding code to check and respond to previously ignored return values
from NVM access functions.

Issue discovered through static analysis.
Signed-off-by: NDave Ertman <david.m.ertman@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Modifying the jumbo frame workaround for 82579, i217 and i218 client parts
to increase the gap between the read and write pointers in the Tx FIFO.
Signed-off-by: NDave Ertman <david.m.ertman@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Make return values more direct, eliminating some gotos and
otherwise unneeded conditionals. This also eliminates some
local variables. Also a few minor cleanups in affected code
so checkpatch won't complain.
Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

All of the code involved with returning the supported physical
layer is actually unused, so delete it.
Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

If ixgbe_write_mbx is called and no mbx->ops.write method
exists, no error code is returned. The corresponding read
function explicitly returns an error in such a case as do
other functions, so this appears to be a minor bug. Fix
it for consistency, and generate return values directly
to make things clearer.
Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In the function ixgbe_get_swfw_sync_semaphore, an incorrect
check was treating success as failure and vice-versa. This led
to manipulating the IXGBE_SWFW_SYNC register without holding
the software semaphore first, which is an error. In addition,
if getting the REGSMP bit in the IXGBE_SW_FW_SYNC register
timed out, no error code would be returned, making the caller
think that it had successfully acquired the lock. Fix both of
those issues and clean up the function a bit, such as make the
name in the comment match the function.
Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Failure to acquire the semaphore would lead to a spurious release
of the semaphore in several functions. Do not release a semaphore
that you did not get.
Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Convert some udelay calls to the preferred usleep_range.
Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When TSO packet is transmitted additional BD w/o mapping is used
to describe the packed. The BD needs special handling in tx
completion.

kernel: Call Trace:
kernel: <IRQ>  [<ffffffff815e19ba>] dump_stack+0x19/0x1b
kernel: [<ffffffff8105dee1>] warn_slowpath_common+0x61/0x80
kernel: [<ffffffff8105df5c>] warn_slowpath_fmt+0x5c/0x80
kernel: [<ffffffff814a8c0d>] ? find_iova+0x4d/0x90
kernel: [<ffffffff814ab0e2>] intel_unmap_page.part.36+0x142/0x160
kernel: [<ffffffff814ad0e6>] intel_unmap_page+0x26/0x30
kernel: [<ffffffffa01f55d7>] bnx2x_free_tx_pkt+0x157/0x2b0 [bnx2x]
kernel: [<ffffffffa01f8dac>] bnx2x_tx_int+0xac/0x220 [bnx2x]
kernel: [<ffffffff8101a0d9>] ? read_tsc+0x9/0x20
kernel: [<ffffffffa01f8fdb>] bnx2x_poll+0xbb/0x3c0 [bnx2x]
kernel: [<ffffffff814d041a>] net_rx_action+0x15a/0x250
kernel: [<ffffffff81067047>] __do_softirq+0xf7/0x290
kernel: [<ffffffff815f3a5c>] call_softirq+0x1c/0x30
kernel: [<ffffffff81014d25>] do_softirq+0x55/0x90
kernel: [<ffffffff810673e5>] irq_exit+0x115/0x120
kernel: [<ffffffff815f4358>] do_IRQ+0x58/0xf0
kernel: [<ffffffff815e94ad>] common_interrupt+0x6d/0x6d
kernel: <EOI>  [<ffffffff810bbff7>] ? clockevents_notify+0x127/0x140
kernel: [<ffffffff814834df>] ? cpuidle_enter_state+0x4f/0xc0
kernel: [<ffffffff81483615>] cpuidle_idle_call+0xc5/0x200
kernel: [<ffffffff8101bc7e>] arch_cpu_idle+0xe/0x30
kernel: [<ffffffff810b4725>] cpu_startup_entry+0xf5/0x290
kernel: [<ffffffff815cfee1>] start_secondary+0x265/0x27b
kernel: ---[ end trace 11aa7726f18d7e80 ]---

Fixes: a848ade4 ("bnx2x: add CSUM and TSO support for encapsulation protocols")
Reported-by: NYulong Pei <ypei@redhat.com>
Cc: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: NDmitry Kravkov <Dmitry.Kravkov@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NCyrille Pitchen <cyrille.pitchen@atmel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When RX checksum offload is enabled at GEM level (bit 24 set in the Network
Control Register), frames with invalid IP, TCP or UDP checksums are
discarted even if promiscuous mode is enabled (bit 4 set in the Network Control
Register).

This was verified with a simple userspace program, which corrupts UDP checksum
using libnetfilter_queue.

Then both IFF_PROMISC bit must be clear in dev->flags and NETIF_F_RXCSUM bit
must be set in dev->features to enable RX checksum offload at GEM level. This
way tcpdump is still able to capture corrupted frames.

Also skb->ip_summed is set to CHECKSUM_UNNECESSARY only when both TCP/IP or
UDP/IP checksums were verified by the GEM. Indeed the GEM may verify only IP
checksum but not the one for ICMP (or other protocol than TCP or UDP).
Signed-off-by: NCyrille Pitchen <cyrille.pitchen@atmel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NCyrille Pitchen <cyrille.pitchen@atmel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The scatter-gather feature will allow to enable the Generic Segmentation Offload.
Generic Segmentation Offload can be enabled/disabled using ethtool -K DEVNAME gso on|off.

e.g:
ethtool -K eth0 gso off

When enabled, the driver may be provided with socket buffers splitted into many fragments.
These fragments need to be queued into the TX ring in reverse order, starting from to the
last one down to the first one, to avoid a race condition with the MAC.
Especially the 'TX_USED' bit in word 1 of the transmit buffer descriptor of the
first fragment should be cleared at the very final step of the queueing algorithm.
This will tell the hardware that fragments are ready to be sent.

Also since the MAC only update the status word of the first buffer descriptor of the
ethernet frame, the queueing algorithm can no longer expect a 'TX_USED' bit to be set by
the MAC into the buffer descriptor following the one for last fragment of the skb.
This is why the driver sets the 'TX_USED' bit before queueing any fragment, so the end of
queue position is well defined for the MAC.
Signed-off-by: NCyrille Pitchen <cyrille.pitchen@atmel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This addition will also allow to configure DMA burst length.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: NCyrille Pitchen <cyrille.pitchen@atmel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

removing unused function as part of driver cleanup.`
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixes sparse warning intrduced by commit 0fef9d03 ("net/mlx4_en: Disable
blueflame using ethtool private flags")
Signed-off-by: NFengguang Wu <fengguang.wu@intel.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ethernet RX DMA buffers are polled in NAPI work queue other than received
directly in DMA RX interrupt handler.
Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix incorrect check introduced in commit fc5ab020 ("cxgb4: Replaced the
backdoor mechanism to access the HW memory with PCIe Window method"). We where
checking for write operation and doing a read, changed it accordingly.
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Get rid of the CONFIG_PM_SLEEP ifdef by annotating the suspend/resume functions
with '__maybe_unused' in order to keep the code simpler and shorter.

While at it, declare the suspend/resume functions in a single line.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allow set_settings() to complete succesfully even if link is
not estabilished and port type isn't known yet.
Signed-off-by: NYaniv Rosner <Yaniv.Rosner@qlogic.com>
Signed-off-by: NDmitry Kravkov <Dmitry.Kravkov@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Sometimes the AQTX answer comes back with no data, but we still want to print
the descriptor that got written back.

Change-ID: I5f734d99b4c95510987413893f0a34626571d474
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Give link a little more time to come back up after setting flow control
before resetting. In the new NVMs it is taking longer for link to come back.
This causes the driver to attempt to reset the link, which then errors
because the firmware was already in the middle of a reset. Also, initialize
err to 0.

Change-ID: I1cc987a944e389d8909c262da5796f50722b4d6b
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Tested-by: NJim Young <jmyoungx@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Reword the error messages. Also add a major version check because
We only want to warn on nvm_minor > expected_minor if
nvm_major == expected_major. Lastly, change an if to an else if
because the two statements will never evaluate to true at the same time.

Change-ID: I6ddf9986f26b35f6879cbeac4fcef04a8497a383
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Copy desc and buffer data even for ARQ events which return error status.
Previously, a check for NVM related AQ commands which is done later in this
function would not recognize that such a command was received and would
not clear nvm_busy flag. This would block access to NVM until a driver reset.
This will fix that.

Change-ID: If69ad74e165b56081c0686b97402511d2e2880c0
Signed-off-by: NKamil Krawczyk <kamil.krawczyk@intel.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

We really don't need to delay an entire millisecond just to get into our
critical section. A microsecond will be sufficient, thank you.

Change-ID: I2d02ece6610007d98cabcb3f42df9a774bb54e59
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The hardware design requires that the driver avoid indicating
checksum offload success on some ipv6 frames with extension
headers.

The code needs to just check for the IPV6EXADD bit and if
it is set punt the checksum to the stack.  I don't know why
the code was checking TCP on inner protocol, as that code
doesn't make any sense to me but seems wrong, so remove it.

Change-ID: I10d3aacdbb1819fb60b4b0eb80e6cc67ef2c9599
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-By: NJim Young <jamesx.m.young@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>