Add the base infrastructure and UAPI for netlink extended ACK
reporting. All "manual" calls to netlink_ack() pass NULL for now and
thus don't get extended ACK reporting.

Big thanks goes to Pablo Neira Ayuso for not only bringing up the
whole topic at netconf (again) but also coming up with the nlattr
passing trick and various other ideas.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Reviewed-by: NDavid Ahern <dsa@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When link transitions from LINK_FAIL to LINK_UP, the commit phase is
not called. This leads to an erroneous state causing slave-link state to
get stuck in "going down" state while its speed and duplex are perfectly
fine. This issue is a side-effect of splitting link-set into propose and
commit phases introduced by de77ecd4 ("bonding: improve link-status
update in mii-monitoring")

This patch fixes these issues by calling commit phase whenever link
state change is proposed.

Fixes: de77ecd4 ("bonding: improve link-status update in mii-monitoring")
Signed-off-by: NMahesh Bandewar <maheshb@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It is necessary to provide ethtool support for displaying and
modifying parameters of dwc-xlgmac.
Signed-off-by: NJie Deng <jiedeng@synopsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

1. Don't get the metric RTAX_ADVMSS of dst.
There are two reasons.
1) Its caller dst_metric_advmss has already invoke dst_metric_advmss
before invoke default_advmss.
2) The ipv4_default_advmss is used to get the default mss, it should
not try to get the metric like ip6_default_advmss.

2. Use sizeof(tcphdr)+sizeof(iphdr) instead of literal 40.

3. Define one new macro IPV4_MAX_PMTU instead of 65535 according to
RFC 2675, section 5.1.
Signed-off-by: NGao Feng <fgao@ikuai8.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

David Ahern says:

====================
rtnetlink: Cleanup user notifications for netdev events

Vlad's recent patch to add the event type to rtnetlink notifications
points out a number of redundant or unnecessary notifications sent to
userspace for events that are essentially internal to the kernel. Trim
the list to put a dent in the notification storm.

v2
- rebased to top of net-next with IFLA_EVENT patch reverted
- dropped removal NETDEV_CHANGEINFODATA since it is intentionally
  only to send a message to userspace
- dropped NOTIFY_PEERS since Vlad's says it is needed for macvlans
- add patches to remove NETDEV_CHANGEUPPER and NETDEV_CHANGE_TX_QUEUE_LEN
  from the event list
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Changing tx queue length generates identical messages:

[LINK]22: dummy1: <BROADCAST,NOARP,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN group default
    link/ether 02:04:f4:b7:5c:d2 brd ff:ff:ff:ff:ff:ff promiscuity 0
    dummy numtxqueues 1 numrxqueues 1 gso_max_size 65536 gso_max_segs 65535
[LINK]22: dummy1: <BROADCAST,NOARP,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN group default
    link/ether 02:04:f4:b7:5c:d2 brd ff:ff:ff:ff:ff:ff promiscuity 0
    dummy numtxqueues 1 numrxqueues 1 gso_max_size 65536 gso_max_segs 65535

Remove NETDEV_CHANGE_TX_QUEUE_LEN from the list of notifiers that generate
notifications.
Signed-off-by: NDavid Ahern <dsa@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

NETDEV_CHANGEUPPER is an internal event; do not generate userspace
notifications.
Signed-off-by: NDavid Ahern <dsa@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

CHANGELOWERSTATE is an internal event; do not generate userspace
notifications.
Signed-off-by: NDavid Ahern <dsa@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

PRECHANGEUPPER is an internal event; do not generate userspace
notifications.
Signed-off-by: NDavid Ahern <dsa@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Changing the master device for a link generates many messages; the one
generated for POST_TYPE_CHANGE is redundant:

[LINK]11: dummy1: <BROADCAST,NOARP,UP,LOWER_UP> mtu 1500 qdisc noqueue master br1 state UNKNOWN group default
    link/ether 02:02:02:02:02:03 brd ff:ff:ff:ff:ff:ff
[LINK]11: dummy1: <BROADCAST,NOARP,UP,LOWER_UP> mtu 1500 qdisc noqueue master br1 state UNKNOWN group default
    link/ether 02:02:02:02:02:03 brd ff:ff:ff:ff:ff:ff

Remove POST_TYPE_CHANGE from the list of notifiers that generate
notifications.
Signed-off-by: NDavid Ahern <dsa@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Changing hardware address generates redundant messages:

[LINK]11: dummy1: <BROADCAST,NOARP,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN group default
    link/ether 02:02:02:02:02:02 brd ff:ff:ff:ff:ff:ff

[LINK]11: dummy1: <BROADCAST,NOARP,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN group default
    link/ether 02:02:02:02:02:02 brd ff:ff:ff:ff:ff:ff

Do not send a notification for the CHANGEADDR notifier.
Signed-off-by: NDavid Ahern <dsa@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

NETDEV_UDP_TUNNEL_PUSH_INFO is an internal notifier; nothing userspace
can do so don't generate a netlink notification.
Signed-off-by: NDavid Ahern <dsa@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Changing MTU on a link currently causes 3 messages to be sent to userspace:

[LINK]11: dummy1: <BROADCAST,NOARP,UP,LOWER_UP> mtu 1490 qdisc noqueue state UNKNOWN group default
    link/ether f2:52:5c:6d:21:f3 brd ff:ff:ff:ff:ff:ff

[LINK]11: dummy1: <BROADCAST,NOARP,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN group default
    link/ether f2:52:5c:6d:21:f3 brd ff:ff:ff:ff:ff:ff

[LINK]11: dummy1: <BROADCAST,NOARP,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN group default
    link/ether f2:52:5c:6d:21:f3 brd ff:ff:ff:ff:ff:ff

Remove the messages sent for PRE_CHANGE_MTU and CHANGE_MTU netdev events.
Signed-off-by: NDavid Ahern <dsa@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When debugging the JIT on an embedded platform or cross build
environment, libbfd may not be available, making it impossible to run
bpf_jit_disasm natively.

Add an option to emit a binary image of the JIT code to a file.  This
file can then be disassembled off line.  Typical usage in this case
might be (pasting mips64 dmesg output to cat command):

   $ cat > jit.raw
   $ bpf_jit_disasm -f jit.raw -O jit.bin
   $ mips64-linux-gnu-objdump -D -b binary -m mips:isa64r2 -EB jit.bin
Signed-off-by: NDavid Daney <david.daney@cavium.com>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Field FL/TPL in register TDES3 is not correctly set on GMAC4.
TX appears to be functional on GMAC 4.10a even if this field is not set,
however, to avoid relying on undefined behavior, set the length in TDES3.

The field has a different meaning depending on if the TSE bit in TDES3
is set or not (TSO). However, regardless of the TSE bit, the field is
not optional. The field is already set correctly when the TSE bit is set.

Since there is no limit for the number of descriptors that can be
used for a single packet, the field should be set to the sum of
the buffers contained in:
[<desc with First Descriptor bit set> ... <desc n> ...
<desc with Last Descriptor bit set>], which should be equal to skb->len.
Signed-off-by: NNiklas Cassel <niklas.cassel@axis.com>
Acked-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Save the filter tid while creating the server filter, which is used
later to retrieve the corresponding filter instance while handling
the filter reply.
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Russell King says:

====================
mvmdio updates

This series of patches update mvmdio for Armada 8k CP110.  A number of
issues were found:

1. The driver fails to disable an interrupt when something goes wrong
   in the probe function.

2. The interrupt is specified in DT to be optional, but the driver
   unconditionally writes to the interrupt mask register, which may
   not exist.

3. The DT binding specifies
    "reg: address and length of the SMI register"
   however, when supporting the interrupt, the size must cover the
   interrupt register as well.  Update the binding documentation
   with this information that was previously omitted.

4. If the register size is too small, have the driver print an error
   and disable use of the interrupt.

5. Armada 8k needs three clocks for the MDIO interface, otherwise the
   SoC hangs (since it is part of one of the ethernet interfaces.)
   GOP clock, MG core clock and MG clock are needed on 8k. Augment the
   binding and driver to allow three clocks to be specified.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allow up to three clocks to be specified and enabled for the orion-mdio
interface, which are required for this interface to be accessible on
Armada 8k platforms.
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Armada 8040 needs three clocks to be enabled for MDIO accesses to work.
Update the binding to allow the extra clocks to be specified.
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Disable the MDIO interrupt, falling back to polled mode, if the resource
size does not allow us to access the interrupt registers.  All current
DT bindings use a size of 0x84, which allows access, but verifying it is
good practice.
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Correct the Marvell Orion MDIO binding document to properly reflect the
cases where an interrupt is present.  Augment the examples to show this.
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The pre-existing write to disable interrupts on the remove path happens
whether we have an interrupt or not.  While this may seem to be a good
idea, this driver is re-used in many different implementations, some
where the binding only specifies four bytes of register space.  This
access causes us to access registers outside of the binding.

Make it conditional on the interrupt being present, which is the same
condition used when enabling the interrupt in the first place.
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the mvmdio driver has an interrupt, it enables the "done" interrupt
after requesting its interrupt handler.  However, probe failure results
in the interrupt being left enabled.  Disable it on the failure path.
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This field is never big enough to warrant 16-bitness.

8-bit accesses enjoy shorted encoding on i386/x86_64 than 16-bit
accesses:

	add/remove: 0/0 grow/shrink: 0/2 up/down: 0/-10 (-10)
	function                                     old     new   delta
	loopback_setup                               169     164      -5
	ether_setup                                  148     143      -5
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Using 16-bit ->hh_len doesn't save any memory, save some .text instead:

	add/remove: 0/0 grow/shrink: 1/6 up/down: 2/-19 (-17)
	function                                     old     new   delta
	neigh_update                                2312    2314      +2
	fwnet_header_cache                           199     197      -2
	eth_header_cache                             101      99      -2
	ip6_finish_output2                          2371    2368      -3
	vrf_finish_output6                          1522    1518      -4
	vrf_finish_output                           1413    1409      -4
	ip_finish_output2                           1627    1623      -4
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A driver may use build_skb() for received packets.
These SKBs then have a head_frag.

Since commit d7e8883c ("net: make GRO aware of
skb->head_frag"), GRO may build frag_list SKBs out of
head_frag received SKBs.
In such a case, the chained SKBs end up with a head_frag.

Commit 07b26c94 ("gso: Support partial splitting at
the frag_list pointer") adds partial segmentation of frag_list
SKB chains into individual SKBs.
However, this is not done if the chained SKBs have any
linear part, because the device may not be able to DMA
the private linear buffer.

A chained frag_list SKB with head_frag is wrongfully
detected in this case as having a private linear part
and thus falls back to software GSO, while in fact the
linear part is backed by a DMA page just like any other frag.

This causes low performance when forwarding those packets
that were built with build_skb()

Allow partial segmentation at the frag_list pointer for
chained SKBs with head_frag.

Note that such SKBs can only be created by GRO, when applied
to received packets with head_frag.
Also note that this change only affects the data path that
performs the partial segmentation at frag_list pointer, and
not any of the other more common data paths.
Signed-off-by: NIlan Tayari <ilant@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Guillaume Nault says:

====================
l2tp: constify l2tp_session_get*() and l2tp_tunnel_find*()

Declare parameters of these functions as "const" where possible.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

l2tp_tunnel_find() and l2tp_tunnel_find_nth() don't modify "net".
Signed-off-by: NGuillaume Nault <g.nault@alphalink.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make l2tp_pernet()'s parameter constant, so that l2tp_session_get*() can
declare their "net" variable as "const".
Also constify "ifname" in l2tp_session_get_by_ifname().
Signed-off-by: NGuillaume Nault <g.nault@alphalink.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Benjamin Herrenschmidt says:

====================
ftgmac100: Rework batch 4 - Misc

This is v2 of the fourth batch of updates to the ftgmac100 driver.

This is a bunch of misc cleanups and fixes, such as properly
disabling HW checksum generation on AST2400 where it's known
to be broken and some chip init updates.

This also adds the ability to turn HW checksum on/off and
configure the ring sizes via ethtool.

v2 Fixes patch 1/10 (NETIF_F_HW_CSUM conversion)

The next (and last) batch will add a few more "features" such
as netpoll, multicast/promist, vlan offload...
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

I haven't seen any improvement above that size on the machines
I've tested with.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We set an arbitrary max at 1024 since we pre-allocate the actual
descriptor arrays and skb arrays to the full size to keep the
code a bit simpler and avoid allocation failures in the reset
task.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Clear stale interrupts on entry, configure FIFO sizes, set FIFO
thresholds, configure interrupt mitigation.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The helpers just take space but don't provide much value. Simple
one line comments are more explanatory.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To remove more confusion. This function is about obtaining the
initial MAC address at driver probe time.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To avoid confusion with the ndo callback and generally be
clearer about the purpose of that function
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

So features can be turned on/off via ethtool
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We found out that HW checksum generation only works from AST2500
onward. This disables it on AST2400 and removes the "no-hw-checksum"
properties in the device-trees. The problem we had wasn't related
to NC-SI.

Also rework the logic testing for that property so it can be used
to disable HW checksum generation and checking regardless of whether
NC-SI is used or not in case other variants out there need this.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We test for aspeed chips to handle a couple of special cases,
but we do that by checking the machine type which isn't right.

Instead check the actual device compatible property. This also
updates the dtsi files for the aspeed SoC to match.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The documentation describes NETIF_F_IP_CSUM as deprecated
so let's switch to NETIF_F_HW_CSUM and use the helper to
handle unhandled protocols.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>