Skip to content

R
raspberrypi-kernel

openeuler / raspberrypi-kernel

通知 13
Star 1
Fork 0
R
raspberrypi-kernel
切换分支/标签
  1. 29 10月, 2005 2 次提交
  3. 26 10月, 2005 1 次提交
  5. 24 10月, 2005 1 次提交
    • L
      cardbus: limit IO windows to 256 bytes · 4196c3af
      由 Linus Torvalds 提交于 
      That's what we've always historically done, and bigger windows seem to
confuse some cardbus bridges. Or something.

Alan reports that this makes the ThinkPad 600x series work properly
again: the 4kB IO window for some reason made IDE DMA not work, which
makes IDE painfully slow even if it works after DMA timeouts.
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
      4196c3af
  7. 18 10月, 2005 2 次提交
  9. 23 9月, 2005 1 次提交
    • I
      [PATCH] pci: fixup parent subordinate busnr · 12f44f46
      由 Ivan Kokshaysky 提交于 
      I believe the change that broke things is introduction of
pci_fixup_parent_subordinate_busnr().

The patch here does two things:
- hunk #1 should fix the problems you've seen when you boot without
  additional "pci" kernel options;
- hunk #2 supposedly fixes boot with "pci=assign-busses" option which
  otherwise hangs Acer TM81xx machines as reported.

Please try this with and without "pci=assign-busses". If it boots,
I'd like to see 'lspci -vvx' for both cases.
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
      12f44f46
  11. 22 9月, 2005 4 次提交
  13. 18 9月, 2005 3 次提交
  15. 15 9月, 2005 1 次提交
  17. 11 9月, 2005 1 次提交
  19. 10 9月, 2005 6 次提交
  21. 09 9月, 2005 18 次提交
    • P
      [PATCH] Separate pci bits out of struct device_node · 1635317f
      由 Paul Mackerras 提交于 
      This patch pulls the PCI-related junk out of struct device_node and
puts it in a separate structure, struct pci_dn.  The device_node now
just has a void * pointer in it, which points to a struct pci_dn for
nodes that represent PCI devices.  It could potentially be used in
future for device-specific data for other sorts of devices, such as
virtual I/O devices.
Signed-off-by: NPaul Mackerras <paulus@samba.org>
      1635317f
    • B
      [PATCH] PCI/libata INTx cleanup · a04ce0ff
      由 Brett M Russ 提交于 
      Simple cleanup to eliminate X copies of the pci_enable_intx() function
in libata.  Moved ahci.c's pci_intx() to pci.c and use it throughout
libata and msi.c.
Signed-off-by: NBrett Russ <russb@emc.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
      a04ce0ff
    • D
      [PATCH] PCI: Support PCM PM CAP version 3 · 3fe9d19f
      由 Daniel Ritz 提交于 
      - support PCI PM CAP version 3 (as defined in PCI PM Interface Spec v1.2)

- pci/probe.c sets the PM state initially to 4 which is D3cold.  add a
  PCI_UNKNOWN

- minor cleanups
Signed-off-by: NDaniel Ritz <daniel.ritz@gmx.ch>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
      3fe9d19f
    • P
      [PATCH] PCI: Add pci_walk_bus function to PCI core (nonrecursive) · cecf4864
      由 Paul Mackerras 提交于 
      The PCI error recovery infrastructure needs to be able to contact all
the drivers affected by a PCI error event, which may mean traversing
all the devices under a given PCI-PCI bridge.  This patch adds a
function to the PCI core that traverses all the PCI devices on a PCI
bus and under any PCI-PCI bridges on that bus (and so on), calling a
given function for each device.  This provides a way for the error
recovery code to iterate through all devices that are affected by an
error event.

This version is not implemented as a recursive function.  Instead,
when we reach a PCI-PCI bridge, we set the pointers to start doing the
devices on the bus under the bridge, and when we reach the end of a
bus's devices, we use the bus->self pointer to go back up to the next
higher bus and continue doing its devices.
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
      cecf4864
    • P
      [PATCH] PCI Hotplug: SGI hotplug driver fixes · 1d2450a4
      由 Prarit Bhargava 提交于 
      These fixes were suggested by pcihpd-discuss, but were dropped in the
initial checkin of the code.  These fixes include cleaning up the
hotplug driver sysfs filename, and some minor code cleanups.  The driver
also requires at least PROM 4.30, not 4.20.
Signed-off-by: NPrarit Bhargava <prarit@sgi.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
      1d2450a4
    • A
      [PATCH] PCI: Fix regression in pci_enable_device_bars · 11f3859b
      由 Alan Stern 提交于 
      This patch (as552) fixes yet another small problem recently added.  If an
attempt to put a PCI device back into D0 fails because the device doesn't
support PCI PM, it shouldn't count as error.  Without this patch the UHCI
controllers on my Intel motherboard don't work.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
      11f3859b
    • G
      [PATCH] PCI: start paying attention to a lot of pci function return values · 95a62965
      由 Greg Kroah-Hartman 提交于 
      Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
      95a62965
    • D
      [PATCH] Make sparc64 use setup-res.c · 085ae41f
      由 David S. Miller 提交于 
      There were three changes necessary in order to allow
sparc64 to use setup-res.c:

1) Sparc64 roots the PCI I/O and MEM address space using
   parent resources contained in the PCI controller structure.
   I'm actually surprised no other platforms do this, especially
   ones like Alpha and PPC{,64}.  These resources get linked into the
   iomem/ioport tree when PCI controllers are probed.

   So the hierarchy looks like this:

   iomem --|
	   PCI controller 1 MEM space --|
				        device 1
					device 2
					etc.
	   PCI controller 2 MEM space --|
				        ...
   ioport --|
            PCI controller 1 IO space --|
					...
            PCI controller 2 IO space --|
					...

   You get the idea.  The drivers/pci/setup-res.c code allocates
   using plain iomem_space and ioport_space as the root, so that
   wouldn't work with the above setup.

   So I added a pcibios_select_root() that is used to handle this.
   It uses the PCI controller struct's io_space and mem_space on
   sparc64, and io{port,mem}_resource on every other platform to
   keep current behavior.

2) quirk_io_region() is buggy.  It takes in raw BUS view addresses
   and tries to use them as a PCI resource.

   pci_claim_resource() expects the resource to be fully formed when
   it gets called.  The sparc64 implementation would do the translation
   but that's absolutely wrong, because if the same resource gets
   released then re-claimed we'll adjust things twice.

   So I fixed up quirk_io_region() to do the proper pcibios_bus_to_resource()
   conversion before passing it on to pci_claim_resource().

3) I was mistakedly __init'ing the function methods the PCI controller
   drivers provide on sparc64 to implement some parts of these
   routines.  This was, of course, easy to fix.

So we end up with the following, and that nasty SPARC64 makefile
ifdef in drivers/pci/Makefile is finally zapped.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
      085ae41f
    • J
      [PATCH] PCI: restore BAR values after D3hot->D0 for devices that need it · 064b53db
      由 John W. Linville 提交于 
      Some PCI devices (e.g. 3c905B, 3c556B) lose all configuration
(including BARs) when transitioning from D3hot->D0.  This leaves such
a device in an inaccessible state.  The patch below causes the BARs
to be restored when enabling such a device, so that its driver will
be able to access it.

The patch also adds pci_restore_bars as a new global symbol, and adds a
correpsonding EXPORT_SYMBOL_GPL for that.

Some firmware (e.g. Thinkpad T21) leaves devices in D3hot after a
(re)boot.  Most drivers call pci_enable_device very early, so devices
left in D3hot that lose configuration during the D3hot->D0 transition
will be inaccessible to their drivers.

Drivers could be modified to account for this, but it would
be difficult to know which drivers need modification.  This is
especially true since often many devices are covered by the same
driver.  It likely would be necessary to replicate code across dozens
of drivers.

The patch below should trigger only when transitioning from D3hot->D0
(or at boot), and only for devices that have the "no soft reset" bit
cleared in the PM control register.  I believe it is safe to include
this patch as part of the PCI infrastructure.

The cleanest implementation of pci_restore_bars was to call
pci_update_resource.  Unfortunately, that does not currently exist
for the sparc64 architecture.  The patch below includes a null
implemenation of pci_update_resource for sparc64.

Some have expressed interest in making general use of the the
pci_restore_bars function, so that has been exported to GPL licensed
modules.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
      064b53db
    • K
      [PATCH] PCI Hotplug: use bus_slot number for name · 1248d636
      由 Kristen Accardi 提交于 
      For systems with multiple hotplug controllers, you need to use more than
just the slot number to uniquely name the slot.  Without a unique slot
name, the pci_hp_register() will fail.  This patch adds the bus number
to the name.
Signed-off-by: NKristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
      1248d636
    • A
      [PATCH] PCI: remove CONFIG_PCI_NAMES · 982245f0
      由 Adrian Bunk 提交于 
      This patch removes CONFIG_PCI_NAMES.
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
      982245f0
    • A
      [PATCH] PCI: Run PCI driver initialization on local node · d42c6997
      由 Andi Kleen 提交于 
      Run PCI driver initialization on local node

Instead of adding messy kmalloc_node()s everywhere run the
PCI driver probe on the node local to the device.

This would not have helped for IDE, but should for
other more clean drivers that do more initialization in probe().
It won't help for drivers that do most of the work
on first open (like many network drivers)
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
      d42c6997
    • J
      [PATCH] PCI Hotplug: rpaphp: Purify hotplug · 56d8456b
      由 John Rose 提交于 
      Currently rpaphp registers the following bus types as hotplug slots:
1) Actual PCI Hotplug slots
2) Embedded/Internal PCI slots
3) PCI Host Bridges

The second and third bus types are not actually direct parents of
removable adapters.  As such, the rpaphp has special case code to fake
results for attributes like power, adapter status, etc.  This patch
removes types 2 and 3 from the rpaphp module.

This patch also changes the DLPAR module so that slots can be
DLPAR-added/removed without having been designated as hotplug-capable.
Signed-off-by: NJohn Rose <johnrose@austin.ibm.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
      56d8456b
    • J
      [PATCH] PCI Hotplug: rpaphp: Export slot enable · 940903c5
      由 John Rose 提交于 
      This patch exports rpaphp_config_pci_adapter() for use by the rpadlpar
module.  It also changes this function by removing any dependencies on
struct slot.  The patch also changes the RPA DLPAR-add path to enable
newly-added slots in a separate step from that which registers them as
hotplug slots.
Signed-off-by: NJohn Rose <johnrose@austin.ibm.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
      940903c5
    • J
      [PATCH] PCI Hotplug: rpaphp: Remove rpaphp_find_pci · 0945cd5f
      由 John Rose 提交于 
      The rpaphp module currently uses a fragile method to find a pci device
by its device node.  This function is unnecessary, so this patch scraps
it.
Signed-off-by: NJohn Rose <johnrose@austin.ibm.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
      0945cd5f
    • J
      [PATCH] PCI Hotplug: rpaphp: Change slot pci reference · 9c209c91
      由 John Rose 提交于 
      The slot structure in the rpaphp module currently references the PCI
contents of the slot using the PCI device of the parent bridge.  This
is unnecessary, since the module is actually interested in the
subordinate bus of the bridge.  The dependency on a PCI bridge device
also prohibits the module from registering hotplug slots that have a
root bridge as a parent, since root bridges on PPC64 don't have PCI
devices.

This patch changes struct slot to reference the PCI subsystem using a
pci_bus rather than a pci_dev.
Signed-off-by: NJohn Rose <johnrose@austin.ibm.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
      9c209c91
    • J
      [PATCH] PCI Hotplug: rpaphp: Move VIO registration · 5eeb8c63
      由 John Rose 提交于 
      Currently, rpaphp registers Virtual I/O slots as hotplug slots.  The
only purpose of this registration is to ensure that the VIO subsystem
is notified of new VIO buses during DLPAR adds.  Similarly, rpaphp
notifies the VIO subsystem when a VIO bus is DLPAR-removed.  The rpaphp
module has special case code to fake results for attributes like power,
adapter status, etc.

The VIO register/unregister functions could just as easily be made from
the DLPAR module.  This patch moves the VIO registration calls to the
DLPAR module, and removes the VIO fluff from rpaphp altogether.
Signed-off-by: NJohn Rose <johnrose@austin.ibm.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
      5eeb8c63
    • J
      [PATCH] PCI Hotplug: rpaphp: Remove unused stuff · bde16841
      由 John Rose 提交于 
      Subject line says it all :)
Signed-off-by: NJohn Rose <johnrose@austin.ibm.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
      bde16841