When using VXLAN tunnels and a sky2 device, I have experienced
checksum failures of the following type:

[ 4297.761899] eth0: hw csum failure
[...]
[ 4297.765223] Call Trace:
[ 4297.765224]  <IRQ>  [<ffffffff8172f026>] dump_stack+0x46/0x58
[ 4297.765235]  [<ffffffff8162ba52>] netdev_rx_csum_fault+0x42/0x50
[ 4297.765238]  [<ffffffff8161c1a0>] ? skb_push+0x40/0x40
[ 4297.765240]  [<ffffffff8162325c>] __skb_checksum_complete+0xbc/0xd0
[ 4297.765243]  [<ffffffff8168c602>] tcp_v4_rcv+0x2e2/0x950
[ 4297.765246]  [<ffffffff81666ca0>] ? ip_rcv_finish+0x360/0x360

	These are reliably reproduced in a network topology of:

container:eth0 == host(OVS VXLAN on VLAN) == bond0 == eth0 (sky2) -> switch

	When VXLAN encapsulated traffic is received from a similarly
configured peer, the above warning is generated in the receive
processing of the encapsulated packet.  Note that the warning is
associated with the container eth0.

        The skbs from sky2 have ip_summed set to CHECKSUM_COMPLETE, and
because the packet is an encapsulated Ethernet frame, the checksum
generated by the hardware includes the inner protocol and Ethernet
headers.

	The receive code is careful to update the skb->csum, except in
__dev_forward_skb, as called by dev_forward_skb.  __dev_forward_skb
calls eth_type_trans, which in turn calls skb_pull_inline(skb, ETH_HLEN)
to skip over the Ethernet header, but does not update skb->csum when
doing so.

	This patch resolves the problem by adding a call to
skb_postpull_rcsum to update the skb->csum after the call to
eth_type_trans.
Signed-off-by: NJay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When vlan tags are stacked, it is very likely that the outer tag is stored
in skb->vlan_tci and skb->protocol shows the inner tag's vlan_proto.
Currently netif_skb_features() first looks at skb->protocol even if there
is the outer tag in vlan_tci, thus it incorrectly retrieves the protocol
encapsulated by the inner vlan instead of the inner vlan protocol.
This allows GSO packets to be passed to HW and they end up being
corrupted.

Fixes: 58e998c6 ("offloading: Force software GSO for multiple vlan tags.")
Signed-off-by: NToshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixes MPLS GSO for case when mpls is compiled as kernel module.

Fixes: 0d89d203 ("MPLS: Add limited GSO support").
Signed-off-by: NPravin B Shelar <pshelar@nicira.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch rearranges the loop in net_rx_action to reduce the
amount of jumping back and forth when reading the code.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We should only perform the softnet_break check after we have polled
at least one device in net_rx_action.  Otherwise a zero or negative
setting of netdev_budget can lock up the whole system.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The commit d75b1ade (net: less
interrupt masking in NAPI) required drivers to leave poll_list
empty if the entire budget is consumed.

We have already had two broken drivers so let's add a check for
this.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch creates a new function napi_poll and moves the napi
polling code from net_rx_action into it.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit cecda693 ("net: keep original skb
which only needs header checking during software GSO") keeps the original
skb for packets that only needs header check, but it doesn't drop the
packet if software segmentation or header check were failed.

Fixes cecda693 ("net: keep original skb which only needs header checking during software GSO")
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NJason Wang <jasowang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This change pulls the core functionality out of __netdev_alloc_skb and
places them in a new function named __alloc_rx_skb.  The reason for doing
this is to make these bits accessible to a new function __napi_alloc_skb.
In addition __alloc_rx_skb now has a new flags value that is used to
determine which page frag pool to allocate from.  If the SKB_ALLOC_NAPI
flag is set then the NAPI pool is used.  The advantage of this is that we
do not have to use local_irq_save/restore when accessing the NAPI pool from
NAPI context.

In my test setup I saw at least 11ns of savings using the napi_alloc_skb
function versus the netdev_alloc_skb function, most of this being due to
the fact that we didn't have to call local_irq_save/restore.

The main use case for napi_alloc_skb would be for things such as copybreak
or page fragment based receive paths where an skb is allocated after the
data has been received instead of before.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

the queue length of sd->input_pkt_queue has been put into qlen,
and impossible to change, since hold the lock
Signed-off-by: NLi RongQing <roy.qing.li@gmail.com>
Acked-by: NEric Dumazet <edumazet@google.com>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The commit 56bfa7ee ("unregister_netdevice : move RTM_DELLINK to
until after ndo_uninit") tried to do this ealier but while doing so
it created a problem. Unfortunately the delayed rtmsg_ifinfo() also
delayed call to fill_info(). So this translated into asking driver
to remove private state and then query it's private state. This
could have catastropic consequences.

This change breaks the rtmsg_ifinfo() into two parts - one takes the
precise snapshot of the device by called fill_info() before calling
the ndo_uninit() and the second part sends the notification using
collected snapshot.

It was brought to notice when last link is deleted from an ipvlan device
when it has free-ed the port and the subsequent .fill_info() call is
trying to get the info from the port.

kernel: [  255.139429] ------------[ cut here ]------------
kernel: [  255.139439] WARNING: CPU: 12 PID: 11173 at net/core/rtnetlink.c:2238 rtmsg_ifinfo+0x100/0x110()
kernel: [  255.139493] Modules linked in: ipvlan bonding w1_therm ds2482 wire cdc_acm ehci_pci ehci_hcd i2c_dev i2c_i801 i2c_core msr cpuid bnx2x ptp pps_core mdio libcrc32c
kernel: [  255.139513] CPU: 12 PID: 11173 Comm: ip Not tainted 3.18.0-smp-DEV #167
kernel: [  255.139514] Hardware name: Intel RML,PCH/Ibis_QC_18, BIOS 1.0.10 05/15/2012
kernel: [  255.139515]  0000000000000009 ffff880851b6b828 ffffffff815d87f4 00000000000000e0
kernel: [  255.139516]  0000000000000000 ffff880851b6b868 ffffffff8109c29c 0000000000000000
kernel: [  255.139518]  00000000ffffffa6 00000000000000d0 ffffffff81aaf580 0000000000000011
kernel: [  255.139520] Call Trace:
kernel: [  255.139527]  [<ffffffff815d87f4>] dump_stack+0x46/0x58
kernel: [  255.139531]  [<ffffffff8109c29c>] warn_slowpath_common+0x8c/0xc0
kernel: [  255.139540]  [<ffffffff8109c2ea>] warn_slowpath_null+0x1a/0x20
kernel: [  255.139544]  [<ffffffff8150d570>] rtmsg_ifinfo+0x100/0x110
kernel: [  255.139547]  [<ffffffff814f78b5>] rollback_registered_many+0x1d5/0x2d0
kernel: [  255.139549]  [<ffffffff814f79cf>] unregister_netdevice_many+0x1f/0xb0
kernel: [  255.139551]  [<ffffffff8150acab>] rtnl_dellink+0xbb/0x110
kernel: [  255.139553]  [<ffffffff8150da90>] rtnetlink_rcv_msg+0xa0/0x240
kernel: [  255.139557]  [<ffffffff81329283>] ? rhashtable_lookup_compare+0x43/0x80
kernel: [  255.139558]  [<ffffffff8150d9f0>] ? __rtnl_unlock+0x20/0x20
kernel: [  255.139562]  [<ffffffff8152cb11>] netlink_rcv_skb+0xb1/0xc0
kernel: [  255.139563]  [<ffffffff8150a495>] rtnetlink_rcv+0x25/0x40
kernel: [  255.139565]  [<ffffffff8152c398>] netlink_unicast+0x178/0x230
kernel: [  255.139567]  [<ffffffff8152c75f>] netlink_sendmsg+0x30f/0x420
kernel: [  255.139571]  [<ffffffff814e0b0c>] sock_sendmsg+0x9c/0xd0
kernel: [  255.139575]  [<ffffffff811d1d7f>] ? rw_copy_check_uvector+0x6f/0x130
kernel: [  255.139577]  [<ffffffff814e11c9>] ? copy_msghdr_from_user+0x139/0x1b0
kernel: [  255.139578]  [<ffffffff814e1774>] ___sys_sendmsg+0x304/0x310
kernel: [  255.139581]  [<ffffffff81198723>] ? handle_mm_fault+0xca3/0xde0
kernel: [  255.139585]  [<ffffffff811ebc4c>] ? destroy_inode+0x3c/0x70
kernel: [  255.139589]  [<ffffffff8108e6ec>] ? __do_page_fault+0x20c/0x500
kernel: [  255.139597]  [<ffffffff811e8336>] ? dput+0xb6/0x190
kernel: [  255.139606]  [<ffffffff811f05f6>] ? mntput+0x26/0x40
kernel: [  255.139611]  [<ffffffff811d2b94>] ? __fput+0x174/0x1e0
kernel: [  255.139613]  [<ffffffff814e2129>] __sys_sendmsg+0x49/0x90
kernel: [  255.139615]  [<ffffffff814e2182>] SyS_sendmsg+0x12/0x20
kernel: [  255.139617]  [<ffffffff815df092>] system_call_fastpath+0x12/0x17
kernel: [  255.139619] ---[ end trace 5e6703e87d984f6b ]---
Signed-off-by: NMahesh Bandewar <maheshb@google.com>
Reported-by: NToshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Roopa Prabhu <roopa@cumulusnetworks.com>
Cc: David S. Miller <davem@davemloft.net>
Acked-by: NEric Dumazet <edumazet@google.com>
Acked-by: NThomas Graf <tgraf@suug.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

So this can be reused for identification of other "items" as well.
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Reviewed-by: NThomas Graf <tgraf@suug.ch>
Acked-by: NJohn Fastabend <john.r.fastabend@intel.com>
Acked-by: NAndy Gospodarek <gospo@cumulusnetworks.com>
Acked-by: NJamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use them to push skb->vlan_tci into the payload and avoid code
duplication.
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Acked-by: NPravin B Shelar <pshelar@nicira.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Name fits better. Plus there's going to be introduced
__vlan_insert_tag later on.
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Acked-by: NPravin B Shelar <pshelar@nicira.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Large receive offloading is known to cause problems if received packets
are passed to other host. Therefore the kernel disables it by calling
dev_disable_lro() whenever a network device is enslaved in a bridge or
forwarding is enabled for it (or globally). For virtual devices we need
to disable LRO on the underlying physical device (which is actually
receiving the packets).

Current dev_disable_lro() code handles this  propagation for a vlan
(including 802.1ad nested vlan), macvlan or a vlan on top of a macvlan.
It doesn't handle other stacked devices and their combinations, in
particular propagation from a bond to its slaves which often causes
problems in virtualization setups.

As we now have generic data structures describing the upper-lower device
relationship, dev_disable_lro() can be generalized to disable LRO also
for all lower devices (if any) once it is disabled for the device
itself.

For bonding and teaming devices, it is necessary to disable LRO not only
on current slaves at the moment when dev_disable_lro() is called but
also on any slave (port) added later.

v2: use lower device links for all devices (including vlan and macvlan)
Signed-off-by: NMichal Kubecek <mkubecek@suse.cz>
Acked-by: NVeaceslav Falico <vfalico@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Tuning coalescing parameters on NIC can be really hard.

Servers can handle both bulk and RPC like traffic, with conflicting
goals : bulk flows want as big GRO packets as possible, RPC want minimal
latencies.

To reach big GRO packets on 10Gbe NIC, one can use :

ethtool -C eth0 rx-usecs 4 rx-frames 44

But this penalizes rpc sessions, with an increase of latencies, up to
50% in some cases, as NICs generally do not force an interrupt when
a packet with TCP Push flag is received.

Some NICs do not have an absolute timer, only a timer rearmed for every
incoming packet.

This patch uses a different strategy : Let GRO stack decides what do do,
based on traffic pattern.

Packets with Push flag wont be delayed.
Packets without Push flag might be held in GRO engine, if we keep
receiving data.

This new mechanism is off by default, and shall be enabled by setting
/sys/class/net/ethX/gro_flush_timeout to a value in nanosecond.

To fully enable this mechanism, drivers should use napi_complete_done()
instead of napi_complete().

Tested:
 Ran 200 netperf TCP_STREAM from A to B (10Gbe mlx4 link, 8 RX queues)

Without this feature, we send back about 305,000 ACK per second.

GRO aggregation ratio is low (811/305 = 2.65 segments per GRO packet)

Setting a timer of 2000 nsec is enough to increase GRO packet sizes
and reduce number of ACK packets. (811/19.2 = 42)

Receiver performs less calls to upper stacks, less wakes up.
This also reduces cpu usage on the sender, as it receives less ACK
packets.

Note that reducing number of wakes up increases cpu efficiency, but can
decrease QPS, as applications wont have the chance to warmup cpu caches
doing a partial read of RPC requests/answers if they fit in one skb.

B:~# sar -n DEV 1 10 | grep eth0 | tail -1
Average:         eth0 811269.80 305732.30 1199462.57  19705.72      0.00
0.00      0.50

B:~# echo 2000 >/sys/class/net/eth0/gro_flush_timeout

B:~# sar -n DEV 1 10 | grep eth0 | tail -1
Average:         eth0 811577.30  19230.80 1199916.51   1239.80      0.00
0.00      0.50
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allow datapath to recognize and extract MPLS labels into flow keys
and execute actions which push, pop, and set labels on packets.

Based heavily on work by Leo Alterman, Ravi K, Isaku Yamahata and Joe Stringer.

Cc: Ravi K <rkerur@gmail.com>
Cc: Leo Alterman <lalterman@nicira.com>
Cc: Isaku Yamahata <yamahata@valinux.co.jp>
Cc: Joe Stringer <joe@wand.net.nz>
Signed-off-by: NSimon Horman <horms@verge.net.au>
Signed-off-by: NJesse Gross <jesse@nicira.com>
Signed-off-by: NPravin B Shelar <pshelar@nicira.com>

rtnl_lock_unregistering*() take rtnl_lock() -- a mutex -- inside a
wait loop. The wait loop relies on current->state to function, but so
does mutex_lock(), nesting them makes for the inner to destroy the
outer state.

Fix this using the new wait_woken() bits.
Reported-by: NFengguang Wu <fengguang.wu@intel.com>
Signed-off-by: NPeter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: NDavid S. Miller <davem@davemloft.net>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Cong Wang <cwang@twopensource.com>
Cc: David Gibson <david@gibson.dropbear.id.au>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jerry Chu <hkchu@google.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Cc: John Fastabend <john.fastabend@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Cc: sfeldma@cumulusnetworks.com <sfeldma@cumulusnetworks.com>
Cc: stephen hemminger <stephen@networkplumber.org>
Cc: Tom Gundersen <teg@jklm.no>
Cc: Tom Herbert <therbert@google.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Vlad Yasevich <vyasevic@redhat.com>
Cc: netdev@vger.kernel.org
Link: http://lkml.kernel.org/r/20141029173110.GE15602@worktop.programming.kicks-ass.netSigned-off-by: NIngo Molnar <mingo@kernel.org>

net_rx_action() can mask irqs a single time to transfert sd->poll_list
into a private list, for a very short duration.

Then, napi_complete() can avoid masking irqs again,
and net_rx_action() only needs to mask irq again in slow path.

This patch removes 2 couples of irq mask/unmask per typical NAPI run,
more if multiple napi were triggered.

Note this also allows to give control back to caller (do_softirq())
more often, so that other softirq handlers can be called a bit earlier,
or ksoftirqd can be wakeup earlier under pressure.

This was developed while testing an alternative to RX interrupt
mitigation to reduce latencies while keeping or improving GRO
aggregation on fast NIC.

Idea is to test napi->gro_list at the end of a napi->poll() and
reschedule one NAPI poll, but after servicing a full round of
softirqs (timers, TX, rcu, ...). This will be allowed only if softirq
is currently serviced by idle task or ksoftirqd, and resched not needed.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

napi_schedule() can be called from any context and has to mask hard
irqs.

Add a variant that can only be called from hard interrupts handlers
or when irqs are already masked.

Many NIC drivers can use it from their hard IRQ handler instead of
generic variant.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Do not reuse skb if it was pfmemalloc tainted, otherwise
future frame might be dropped anyway.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NRoman Gushchin <klamm@yandex-team.ru>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add ndo_gso_check which a device can define to indicate whether is
is capable of doing GSO on a packet. This funciton would be called from
the stack to determine whether software GSO is needed to be done. A
driver should populate this function if it advertises GSO types for
which there are combinations that it wouldn't be able to handle. For
instance a device that performs UDP tunneling might only implement
support for transparent Ethernet bridging type of inner packets
or might have limitations on lengths of inner headers.
Signed-off-by: NTom Herbert <therbert@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Testing xmit_more support with netperf and connected UDP sockets,
I found strange dst refcount false sharing.

Current handling of IFF_XMIT_DST_RELEASE is not optimal.

Dropping dst in validate_xmit_skb() is certainly too late in case
packet was queued by cpu X but dequeued by cpu Y

The logical point to take care of drop/force is in __dev_queue_xmit()
before even taking qdisc lock.

As Julian Anastasov pointed out, need for skb_dst() might come from some
packet schedulers or classifiers.

This patch adds new helper to cleanly express needs of various drivers
or qdiscs/classifiers.

Drivers that need skb_dst() in their ndo_start_xmit() should call
following helper in their setup instead of the prior :

	dev->priv_flags &= ~IFF_XMIT_DST_RELEASE;
->
	netif_keep_dst(dev);

Instead of using a single bit, we use two bits, one being
eventually rebuilt in bonding/team drivers.

The other one, is permanent and blocks IFF_XMIT_DST_RELEASE being
rebuilt in bonding/team. Eventually, we could add something
smarter later.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Julian Anastasov <ja@ssi.bg>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Marking this as static allows compiler to inline it.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some TSO engines might have a too heavy setup cost, that impacts
performance on hosts sending small bursts (2 MSS per packet).

This patch adds a device gso_min_segs, allowing drivers to set
a minimum segment size for TSO packets, according to the NIC
performance.

Tested on a mlx4 NIC, this allows to get a ~110% increase of
throughput when sending 2 MSS per packet.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Its unfortunate we have to walk again skb list to find the tail
after segmentation, even if data is probably hot in cpu caches.

skb_segment() can store the tail of the list into segs->prev,
and validate_xmit_skb_list() can immediately get the tail.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Validation of skb can be pretty expensive :

GSO segmentation and/or checksum computations.

We can do this without holding qdisc lock, so that other cpus
can queue additional packets.

Trick is that requeued packets were already validated, so we carry
a boolean so that sch_direct_xmit() can validate a fresh skb list,
or directly use an old one.

Tested on 40Gb NIC (8 TX queues) and 200 concurrent flows, 48 threads
host.

Turning TSO on or off had no effect on throughput, only few more cpu
cycles. Lock contention on qdisc lock disappeared.

Same if disabling TX checksum offload.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Per commit "77873803 net_dma: mark broken" net_dma is no longer used
and there is no plan to fix it.

This is the mechanical removal of bits in CONFIG_NET_DMA ifdef guards.
Reverting the remainder of the net_dma induced changes is deferred to
subsequent patches.

Marked for stable due to Roman's report of a memory leak in
dma_pin_iovec_pages():

    https://lkml.org/lkml/2014/9/3/177

Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: David Whipple <whipple@securedatainnovations.ch>
Cc: Alexander Duyck <alexander.h.duyck@intel.com>
Cc: <stable@vger.kernel.org>
Reported-by: NRoman Gushchin <klamm@yandex-team.ru>
Acked-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

No caller or macro uses the return value so make all
the functions return void.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The send_check logic was only interesting in cases of TCP offload and
UDP UFO where the checksum needed to be initialized to the pseudo
header checksum. Now we've moved that logic into the related
gso_segment functions so gso_send_check is no longer needed.
Signed-off-by: NTom Herbert <therbert@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit ce93718f ("net: Don't keep
around original SKB when we software segment GSO frames") frees the
original skb after software GSO even for dodgy gso skbs. This breaks
the stream throughput from untrusted sources, since only header
checking was done during software GSO instead of a true
segmentation. This patch fixes this by freeing the original gso skb
only when it was really segmented by software.

Fixes ce93718f ("net: Don't keep
around original SKB when we software segment GSO frames.")

Cc: David S. Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NJason Wang <jasowang@redhat.com>
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

__netdev_adjacent_dev_insert may add adjust device of different net
namespace, without proper check it leads to emergence of broken
sysfs links from/to devices in another namespace.
Fix: rewrite netdev_adjacent_is_neigh_list macro as a function,
     move net_eq check into netdev_adjacent_is_neigh_list.
     (thanks David)
     related to: 4c75431aSigned-off-by: NAlexander Fomichev <git.user@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

These code is now protected by rtnl lock, rcu read lock
is useless now.
Signed-off-by: NCong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add __rcu notation to qdisc handling by doing this we can make
smatch output more legible. And anyways some of the cases should
be using rcu_dereference() see qdisc_all_tx_empty(),
qdisc_tx_chainging(), and so on.

Also *wake_queue() API is commonly called from driver timer routines
without rcu lock or rtnl lock. So I added rcu_read_lock() blocks
around netif_wake_subqueue and netif_tx_wake_queue.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add __rcu notation to qdisc handling by doing this we can make
smatch output more legible. And anyways some of the cases should
be using rcu_dereference() see qdisc_all_tx_empty(),
qdisc_tx_chainging(), and so on.

Also *wake_queue() API is commonly called from driver timer routines
without rcu lock or rtnl lock. So I added rcu_read_lock() blocks
around netif_wake_subqueue and netif_tx_wake_queue.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In commit 50cbe9ab ("net: Validate xmit SKBs right when we
pull them out of the qdisc") the validation code was moved out of
dev_hard_start_xmit and into dequeue_skb.

However this overlooked the fact that we do not always enqueue
the skb onto a qdisc. First situation is if qdisc have flag
TCQ_F_CAN_BYPASS and qdisc is empty.  Second situation is if
there is no qdisc on the device, which is a common case for
software devices.

Originally spotted and inital patch by Alexander Duyck.
As a result Alex was seeing issues trying to connect to a
vhost_net interface after commit 50cbe9ab was applied.

Added a call to validate_xmit_skb() in __dev_xmit_skb(), in the
code path for qdiscs with TCQ_F_CAN_BYPASS flag, and in
__dev_queue_xmit() when no qdisc.

Also handle the error situation where dev_hard_start_xmit() could
return a skb list, and does not return dev_xmit_complete(rc) and
falls through to the kfree_skb(), in that situation it should
call kfree_skb_list().

Fixes:  50cbe9ab ("net: Validate xmit SKBs right when we pull them out of the qdisc")
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This flag indicates that an invalid checksum was detected in the
packet. __skb_mark_checksum_bad helper function was added to set this.

Checksums can be marked bad from a driver or the GRO path (the latter
is implemented in this patch). csum_bad is checked in
__skb_checksum_validate_complete (i.e. calling that when ip_summed ==
CHECKSUM_NONE).

csum_bad works in conjunction with ip_summed value. In the case that
ip_summed is CHECKSUM_NONE and csum_bad is set, this implies that the
first (or next) checksum encountered in the packet is bad. When
ip_summed is CHECKSUM_UNNECESSARY, the first checksum after the last
one validated is bad. For example, if ip_summed == CHECKSUM_UNNECESSARY,
csum_level == 1, and csum_bad is set-- then the third checksum in the
packet is bad. In the normal path, the packet will be dropped when
processing the protocol layer of the bad checksum:
__skb_decr_checksum_unnecessary called twice for the good checksums
changing ip_summed to CHECKSUM_NONE so that
__skb_checksum_validate_complete is called to validate the third
checksum and that will fail since csum_bad is set.
Signed-off-by: NTom Herbert <therbert@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now fundamentally we can process lists of SKBs as cheaply
as single packets.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Just maintain the list properly by returning the head of the remaining
SKB list from dev_hard_start_xmit().
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>