PF needs to assert the VF reset when it receives the request to
reset from VF. After receiving request PF ackknowledges the
request by replying back MBX_ASSERTING_RESET message to VF.
VF then goes to pending state and wait for hardware to complete
the reset.

This patch contains code to handle the received VF message, inform
the VF of assertion and reset the VF using cmdq interface.
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Reset Asserting message is forwarded by PF to inform VF about
the hardware reset which is about to happen. This might be due
to the earlier VF reset request received by the PF or because PF
for any reason decides to undergo reset. This message results in
VF to go in pending state in which it polls the hardware to
complete the reset and then further resets/tears its own stack.
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Current mailbox CRQ could consists of both synchronous and async
responses from the PF. Synchronous responses are time critical
and should be handed over to the waiting tasks/context as quickly
as possible otherwise timeout occurs.

Above problem gets accentuated if CRQ consists of even single
async message. Hence, it is important to have quick handling of
synchronous messages and maybe deferred handling of async messages
This patch introduces separate ARQ(async receive queues) for the
async messages. These messages are processed later with repsect
to mailbox task while synchronous messages still gets processed
in context to mailbox interrupt.

ARQ is important as VF reset introduces some new async messages
like MBX_ASSERTING_RESET which adds up to the presssure on the
responses for synchronousmessages and they timeout even more
quickly.
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After the hardware reset we should re-fetch the configuration from
PF like queue info and tc info. This might have impact on allocations
made like that of TQPs. Hence, we should release all such allocations
and re-allocate fresh according to new fetched configuration after
reset.
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After VF driver knows that hardware reset has been performed
successfully, it should proceed ahead and reset the enet layer.
This primarily consists of bringing down interface, clearing
TX/RX rings, disassociating vectors from ring etc.
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

VF driver depends upon PF to eventually reset the hardware. This
request is made using the mailbox command. This patch adds the
required function to acheive above.
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This introduces the hclge device reset states of "requested" and
"pending" and also its handling in context to Reset Service Task.

Device gets into requested state because of any VF reset request
asserted from upper layers, for example due to watchdog timeout
expiration. Requested state would result in eventually forwarding
the VF reset request to PF which would actually reset the VF.

Device will get into pending state if:
1. VF receives the acknowledgement from PF for the VF reset
   request it originally sent to PF.
2. Reset Service Task detects that after asserting VF reset for
   certain times the data-path is not working and device then
   decides to assert full VF reset(this means also resetting the
   PCIe interface).
3. PF intimates the VF that it has undergone reset.
Pending state would result in VF to poll for hardware reset
completion status and then resetting the stack/enet layer, which
in turn means reinitializing the ring management/enet layer.

Note: we would be adding support of 3. later as a separate patch.
This decision should not affect VF reset as its event handling
is generic in nature.
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

VF reset would involve handling of different reset related events
from the stack, physical function, mailbox etc. Reset service task
would be used in servicing such reset event requests and later
handling the hardware completions waits and initiating the stack
resets.
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

HNS3 drivers enet layer, used for the ring management and stack
interaction, is common to both VF and PF. PF already supports reset
functionality to handle the network stack watchdog timeout trigger
but the existing code is not generic enough to be used to support VF
reset as well.
This patch does following:
1. Makes the existing watchdog timeout handler in enet layer generic
   i.e. suitable for both VF and PF and
2. Introduces the new reset event handler for the VF code.
3. Changes existing reset event handler of PF code to initialize the
   reset level
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a VF is trusted, all promiscuous traffic will only be sent to that VF.
In normal operation promiscuous traffic is sent to the PF. There can be
only one trusted VF per PF
Signed-off-by: NIntiyaz Basha <intiyaz.basha@cavium.com>
Signed-off-by: NFelix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is needed to query the mux_id and flags of a rmnet device.
Signed-off-by: NSubash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Define new netlink attributes for rmnet mux_id and flags. These
flags / mux_id were earlier using vlan flags / id respectively.
The flag bits are also moved to uapi and are renamed with
prefix RMNET_FLAG_*.

Also add the rmnet policy to handle the new netlink attributes.
Signed-off-by: NSubash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Device of the de-aggregated skb is correctly assigned after inspecting
the mux_id, so remove the assignment in rmnet_map_deaggregate().
Signed-off-by: NSubash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSubash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix warnings which were reported when running with sparse
(make C=1 CF=-D__CHECK_ENDIAN__)

drivers/net/ethernet/qualcomm/rmnet/rmnet_handlers.c:81:15:
warning: cast to restricted __be16
drivers/net/ethernet/qualcomm/rmnet/rmnet_map_data.c:271:37:
warning: incorrect type in assignment (different base types)
expected unsigned short [unsigned] [usertype] pkt_len
got restricted __be16 [usertype] <noident>
drivers/net/ethernet/qualcomm/rmnet/rmnet_map_data.c:287:29:
warning: incorrect type in assignment (different base types)
expected unsigned short [unsigned] [usertype] pkt_len
got restricted __be16 [usertype] <noident>
drivers/net/ethernet/qualcomm/rmnet/rmnet_map_data.c:310:22:
warning: cast to restricted __be16
drivers/net/ethernet/qualcomm/rmnet/rmnet_map_data.c:319:13:
warning: cast to restricted __be16
drivers/net/ethernet/qualcomm/rmnet/rmnet_map_command.c:49:18:
warning: cast to restricted __be16
drivers/net/ethernet/qualcomm/rmnet/rmnet_map_command.c:50:18:
warning: cast to restricted __be32
drivers/net/ethernet/qualcomm/rmnet/rmnet_map_command.c:74:21:
warning: cast to restricted __be16
Signed-off-by: NSubash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Array mvpp2_pools is being indexed by long_log_pool, however this
looks like a cut-n-paste bug and in fact should be short_log_pool.

Detected by CoverityScan, CID#1466113 ("Copy-paste error")

Fixes: 576193f2 ("net: mvpp2: jumbo frames support")
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Acked-by: NAntoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In 'auto-neg off' the device have sent AN (auto-negotiation) frames
with the forced speed. Thus, fix it using an_disable_admin field in
Port type and speed (PTYS) register. This field indicates if speed
negotiation frames would be send by the port or not.

Add the field and enable/disable it for 'auto-neg on/off', make the
port to start/stop sending AN (auto-negotiation) frames. Note that for
SwitchX2 the behavior doesn't change (i.e support only AN enabled with
forced speed).
Signed-off-by: NTal Bar <talb@mellanox.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This new firmware contains:
	- Support for auto-neg disable mode
Signed-off-by: NTal Bar <talb@mellanox.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When phy exists, phy_ethtool_ksettings_get function is enough to get the
link ksettings. If the phy exists, get_link_ksettings function can return
directly after phy_ethtool_ksettings_get is called.
Signed-off-by: NFuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for querying speed and duplex by ethtool ethX
to VF.
Signed-off-by: NFuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds ethtool_ops.get_link support to VF.
Signed-off-by: NFuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixed link mode is returned by hns3_get_link_ksettings. It is
unreasonable.

This patch fixes it by adding some related functions to get link
mode from hardware.
Signed-off-by: NFuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since we change the update rate of int_gl from every interrupt to every
one hundred interrupts, the old way to get time interval by int_gl value
is not accurate. This patch calculates the time interval using the jiffies
value.
Signed-off-by: NFuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The interrupt coalescing self-adaptive function updates the int_gl every
interrupt. The GL update rate is too faster to get a better new GL value.
This patch changes the GL update rate to every one hundred interrupts.
The GL update rate is defined by HNS3_INT_ADAPT_DOWN_START.
Signed-off-by: NFuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It may need more time for IMP handle some command, such as reset.
This patch enlarges the max time for cmd timeout.

Driver will check the IMP result every us, it may break through the
loop when get the right result. So not all command need the max time.
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is no module that is dependent on hclge or hclgevf's symbol,
but hns_enet need them to provide ops for it to run. When there is
a need to auto load the hns3 driver, the auto load will fail because
hclge or hclgevf is not loaded.

Hns_enet has already exported the pci table, so this patch exports
the pci table for hclge and hclgevf module too.
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The vlan table in hardware is clear after PF/Core/IMP/Global
reset, which will cause vlan tagged packets not being received
problem.

This patch fixes it by restoring the vlan table after reset.
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

VF queue reset flow is different from PF queue reset flow.
VF driver should stop VF queue first, then send message to PF
and PF do the reset. PF should send a response to VF after
PF complete the queue reset, VF can initialize the queue hw
after get the response.
This patch fixes the VF queue reset flow as the correct step.
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When changing the mtu, the max frame size also will be changed. The tx
buffer size and the rx buffer size to be allocated are determined by max
frame size. So when max frame size is changed, the tx buffer and rx buffer
need to be reallocated.

When the tc_num is changed, the tx buffer and rx buffer need to be
reallocated too. So calling set_mtu and buffer_alloc separately is better.
Signed-off-by: NFuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

top_hierarchy arg can be determined by comparing parent_resource_id to
DEVLINK_RESOURCE_ID_PARENT_TOP so it does not need to be a separate
argument.
Signed-off-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If FW supports RDMA WRITE_COMPLETION functionality, then advertise that
to the ULDs. This will be used by iw_cxgb4 to allow WRITE_COMPLETION
work requests.
Signed-off-by: NPotnuri Bharat Teja <bharat@chelsio.com>
Signed-off-by: NRaju Rangoju <rajur@chelsio.com>
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If FW supports RDMA WRITE_WITH_IMMEDATE functionality, then advertise
that
to the ULDs. This will be used by iw_cxgb4 to allow WRITE_WITH_IMMEDIATE
work requests.
Signed-off-by: NPotnuri Bharat Teja <bharat@chelsio.com>
Signed-off-by: NRaju Rangoju <rajur@chelsio.com>
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support to query FW for the HW SRQ table start/end, and
advertise that for ULDs.
Signed-off-by: NRaju Rangoju <rajur@chelsio.com>
Reviewed-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

- This patch adds support to initialise srq table and read srq entries
Signed-off-by: NRaju Rangoju <rajur@chelsio.com>
Reviewed-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

- Add srq table query cpl support for srq
- Add cpl_abort_req_rss6 and cpl_abort_rpl_rss6 structs.
- Add accessors, macros to get the SRQ IDX value.
Signed-off-by: NRaju Rangoju <rajur@chelsio.com>
Reviewed-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In several places struct device is referenced by using &tp->pci_dev->dev.
Add helper tp_to_dev() to improve code readability.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Changing the argument type to struct rtl8169_private * is more in line
with the other functions in the driver and it allows to reduce the code size.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Changing the type of the first argument to struct rtl8169_private * is more
in line with the other functions in the driver and it allows to reduce the
code size.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace open-coded functionality with eth_mac_addr().
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This changes the respective line in /proc/interrupts from

 49:          x          x  mv88e6xxx-g1   7 Edge      mv88e6xxx-g1

to

 49:          x          x  mv88e6xxx-g1   7 Edge      mv88e6xxx-g2

which makes more sense.
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>