Signed-off-by: NScott Teel <scott.teel@hp.com>
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

On encountering unexpected error conditions from driver initiated
commands, print something useful like CDB and sense data rather than
something useless like the kernel virtual address of the command buffer.
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Do no rescan on every events -- way too many rescans are
triggered if we don't filter the events.  Limit rescans
to be triggered by the following set of events:

 * controller state change
 * enclosure hot plug
 * physical drive state change
 * logical drive state change
 * redundant controller state change
 * accelerated io enabled/disabled
 * accelerated io configuration change
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Don't wait for *all* commands to complete, only for accelerated mode
commands.
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Add controller-based data-at-rest encryption compatibility
to ioaccel2 path (HP SSD Smart Path).

Encryption feature requires driver to supply additional fields
for encryption enable, tweak index, and data encryption key index
in the ioaccel2 request structure.

Encryption enable flag and data encryption key index come from
raid_map data structure from raid offload command.

During ioaccel2 submission, check device structure's raid map to see if
encryption is enabled for the device. If so, call new function below.

Add function set_encrypt_ioaccel2 to set encryption flag, data encryption key
index, and calculate tweak value from request's logical block address.
Signed-off-by: NScott Teel <scott.teel@hp.com>
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NScott Teel <scott.teel@hp.com>
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Change the handling of HP SSD Smart Path errors with status:
  0x02 CHECK CONDITION
  0x08 BUSY
  0x18 RESERVATION CONFLICT
  0x40 TASK ABORTED
So that they get retried on the RAID Path.
Signed-off-by: NScott Teel <scott.teel@hp.com>
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Code was confused and assumed that page zero was not
VPD page and all non-zero pages were VPD pages.
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Allow driver to schedule a rescan whenever a request fails on the ioaccel2 path.
This eliminates the possibility of driver getting stuck in non-ioaccel mode.

IOaccel mode (HP SSD Smart Path) is disabled by driver upon error detection.
Driver relied on idea that request would be retried through normal path, and a
subsequent error would occur on that path, and be processed by controller
firmware.  As part of that process, controller disables ioaccel mode and later
reinstates it, signalling driver to change modes.

In some error cases, the error will not duplicate on the standard path,
so the driver could get stuck in non-ioaccel mode.
To avoid that, we allow driver to request a rescan during the next run of the
rescan thread.
Signed-off-by: NScott Teel <scott.teel@hp.com>
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Allow SSD Smart Path for a controller to be disabled by
the user, regardless of settings in controller firmware
or array configuration.

To disable:     echo 0 > /sys/class/scsi_host/host<id>/acciopath_status
To re-enable:   echo 1 > /sys/class/scsi_host/host<id>/acciopath_status
To check state: cat /sys/class/scsi_host/host<id>/acciopath_status
Signed-off-by: NScott Teel <scott.teel@hp.com>
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Load balance across members of a N-way mirror set, and
handle the meta-RAID levels: R10, R50, R60.
Signed-off-by: NScott Teel <scott.teel@hp.com>
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Otherwise we could wind up using incorrect raid map data, and
then very bad things would likely happen.
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Underlying firmware cannot handle task abort on accelerated path (SSD Smart Path).
Change abort requests for accelerated path commands to physical target reset.
Send reset request on normal IO path.
Signed-off-by: NScott Teel <scott.teel@hp.com>
Signed-off-by: NMike Miller <michael.miller@canonical.com>
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NScott Teel <scott.teel@hp.com>
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NScott Teel <scott.teel@hp.com>
Signed-off-by: NJoe Handzik <Joseph.T.Handzik@hp.com>
Signed-off-by: NMike Miller <michael.miller@canonical.com>
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NScott Teel <scott.teel@hp.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NMike MIller <michael.miller@canonical.com>
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NMike Miller <michael.miller@canonical.com>
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NMike Miller <michael.miller@canonical.com>
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NScott Teel <scott.teel@hp.com>
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NScott Teel <scott.teel@hp.com>
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

* Do not check event bits on locked up controllers to
  see if they need to be rescanned.
* Do not initiate any device rescans on controllers
  which are known to be locked up.
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

For shared SAS configurations, hosts need to poll Smart Arrays
periodically in order to be able to detect configuration changes
such as logical drives being added or removed from remote hosts.
A register on the controller indicates when such events have
occurred, and the driver polls the register via a workqueue
and kicks off a rescan of devices if such an event is detected.
Additionally, changes to logical drive raid offload eligibility
are autodetected in this way.
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NScott Teel <scott.teel@hp.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

When rescanning for logical drives, store information about whather
raid offload is enabled for each logical drive, and update the driver's
internal record of this.
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

This enables sending i/o's destined for RAID logical drives
which can be serviced by a single physical disk down a different,
faster i/o path directly to physical drives for certain logical
volumes on SSDs bypassing the Smart Array RAID stack for a
performance improvement.
Signed-off-by: NMatt Gates <matthew.gates@hp.com>
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NScott Teel <scott.teel@hp.com>
Signed-off-by: NMike Miller <michael.miller@canonical.com>
Signed-off-by: NDon Brace <brace@beardog.cce.hp.com>
Signed-off-by: NJoe Handzik <joseph.t.handzik@hp.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

For "mode 1" io accelerated commands, the command tag is in
a different location than for commands that go down the normal
RAID path, so the abort handler needs to take this into account.
Signed-off-by: NScott Teel <scott.teel@hp.com>
Signed-off-by: NMike Miller <michael.miller@canonical.com>
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

When commands sent down the "fast path" fail, they must be re-tried down the
normal RAID path.  We do this by kicking i/o's back to the scsi mid layer with
a DID_SOFT_ERROR status, which causes them to be retried.  This won't work for
SG_IO's and other non REQ_TYPE_FS i/o's which could get kicked all the way back
to the application, which may have no idea that the command needs resubmitting
and likely no way to resubmit it in such a way the that driver can recognize it
as a resubmit and send it down the normal RAID path.  So we just always send
non REQ_TYPE_FS i/o's down the normal RAID path, never down the "fast path".
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

For certain i/o's to certain devices (unmasked physical disks) we
can bypass the RAID stack firmware and do the i/o to the device
directly and it will be faster.
Signed-off-by: NMatt Gates <matthew.gates@hp.com>
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

This is normally optional, but for SSD Smart Path support (in
subsequent patches) it is required.
Signed-off-by: NMatt Gates <matthew.gates@hp.com>
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

There is an extended report luns command which contains
additional information about physical devices.  In particular
we need to get the physical device handle so we can use an
alternate i/o path for fast physical devices like SSDs so
we can speed up certain i/o's by bypassing the RAID stack
code in the controller firmware.
Signed-off-by: NMatt Gates <matthew.gates@hp.com>
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Commit 254f796b updated
the driver to use 16 MSI-X vectors, despite the fact that
older controllers would provide only 4.
This was causing MSI-X registration to drop down to INTx
mode. But as the controller support performant mode, the
initialisation will become confused and cause the machine
to stall during boot.

This patch fixes up the MSI-X registration to re-issue
the pci_enable_msix() call with the correct number of
MSI-X vectors. With that the hpsa driver continues to
works on older controllers like the P200.
Signed-off-by: NHannes Reinecke <hare@suse.de>
Acked-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

We were clobbering the SCSI status and setting
cmd->result = DID_SOFT_ERROR << 16; to get a retry,
but better to let the mid layer handle the unit
attention.
Signed-off-by: NMatt Gates <matthew.gates@hp.com>
Acked-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Immediately following a hard board reset, There are some
mandatory delays during which we must not access the board
and during which we might miss the "not ready" status,
therefore it is a mistake to look for and expect to see
the "not ready" status.
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

This used to be the default, but at some point the firmware guys
changed the default and I failed to notice.  Now to get unit
attention notifications, you must twiddle a bit indicating you
want them.
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

The field contains more bits than just the one
to indicate whether scsi prefetch should be turned on.
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Much simpler and avoids races starting/stopping the thread.
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Remove PCI ID for the never shipped P822se.
Signed-off-by: NMike Miller <mike.miller@hp.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

If a fifo full condition is encountered, i/o requests will stack
up in the h->reqQ queue.  The only thing which empties this queue
is start_io, which only gets called when new i/o requests come in.
If none are forthcoming, i/o in h->reqQ will be stalled.

To fix this, whenever fifo full condition is encountered, this
is recorded, and the interrupt handler examines this to see
if a fifo full condition was recently encountered when a
command completes and will call start_io to prevent i/o's in
h->reqQ from getting stuck.

I've only ever seen this problem occur when running specialized
test programs that pound on the the CCISS_PASSTHRU ioctl.
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>