It looks like we weren't correctly placing the pages from buffers that had
been used to return a filter programming status back on the ring. As a
result they were being overwritten and tracking of the pages was lost.

This change works to correct that by incorporating part of
i40e_put_rx_buffer into the programming status handler code. As a result we
should now be correctly placing the pages for those buffers on the
re-allocation list instead of letting them stay in place.

Fixes: 0e626ff7 ("i40e: Fix support for flow director programming status")
Reported-by: NAnders K. Pedersen <akp@cohaesio.com>
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAnders K Pedersen <akp@cohaesio.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Caller needs to acquire the lock. Called functions will not.

Fixes: 09f79fd4 ("i40e: avoid NVM acquire deadlock during NVM update")
Signed-off-by: NStefano Brivio <sbrivio@redhat.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Changing the TX ring parameters with an XDP program attached may
cause the XDP queues to be cleared and the TX rings to be incorrectly
configured.

Fix by doing correct ring accounting in setup call.

Fixes: 33fdc82f ("ixgbe: add support for XDP_TX action")
Signed-off-by: NJohn Fastabend <john.fastabend@gmail.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The ixgbe driver use the compile check to determine if it can
send TLPs to Root Port with the Relaxed Ordering Attribute set,
this is too inconvenient, now the new flag PCI_DEV_FLAGS_NO_RELAXED_ORDERING
has been added to the kernel and we could check the bit4 in the PCIe
Device Control register to determine whether we should use the Relaxed
Ordering Attributes or not, so use this new way in the ixgbe driver.
Signed-off-by: NDing Tianhong <dingtianhong@huawei.com>
Acked-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The new flag PCI_DEV_FLAGS_NO_RELAXED_ORDERING has been added
to indicate that Relaxed Ordering Attributes (RO) should not
be used for Transaction Layer Packets (TLP) targeted toward
these affected Root Port, it will clear the bit4 in the PCIe
Device Control register, so the PCIe device drivers could
query PCIe configuration space to determine if it can send
TLPs to Root Port with the Relaxed Ordering Attributes set.

With this new flag  we don't need the config ARCH_WANT_RELAX_ORDER
to control the Relaxed Ordering Attributes for the ixgbe drivers
just like the commit 1a8b6d76 ("net:add one common config...") did,
so revert this commit.
Signed-off-by: NDing Tianhong <dingtianhong@huawei.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In ixgbe_clear_udp_tunnel_port(), we read the IXGBE_VXLANCTRL register
and then try to mask some bits out of the value, using the logical
instead of bitwise and operator.

Fixes: a21d0822 ("ixgbe: add support for geneve Rx offload")
Signed-off-by: NSabrina Dubroca <sd@queasysnail.net>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In cases where PHY register access is not supported, don't mislead
a caller into thinking that it is supported by returning a PHY
address. Instead, return -EOPNOTSUPP when PHY access is not
supported.
Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When introducing the functions to read the NVM through the AdminQ, we
did not correctly mark the wb_desc.

Fixes: 7073f46e ("i40e: Add AQ commands for NVM Update for X722", 2015-06-05)
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

X722 devices use the AdminQ to access the NVM, and this requires taking
the AdminQ lock. Because of this, we lock the AdminQ during
i40e_read_nvm(), which is also called in places where the lock is
already held, such as the firmware update path which wants to lock once
and then unlock when finished after performing several tasks.

Although this should have only affected X722 devices, commit
96a39aed ("i40e: Acquire NVM lock before reads on all devices",
2016-12-02) added locking for all NVM reads, regardless of device
family.

This resulted in us accidentally causing NVM acquire timeouts on all
devices, causing failed firmware updates which left the eeprom in
a corrupt state.

Create unsafe non-locked variants of i40e_read_nvm_word and
i40e_read_nvm_buffer, __i40e_read_nvm_word and __i40e_read_nvm_buffer
respectively. These variants will not take the NVM lock and are expected
to only be called in places where the NVM lock is already held if
needed.

Since the only caller of i40e_read_nvm_buffer() was in such a path,
remove it entirely in favor of the unsafe version. If necessary we can
always add it back in the future.

Additionally, we now need to hold the NVM lock in i40e_validate_checksum
because the call to i40e_calc_nvm_checksum now assumes that the NVM lock
is held. We can further move the call to read I40E_SR_SW_CHECKSUM_WORD
up a bit so that we do not need to acquire the NVM lock twice.

This should resolve firmware updates and also fix potential raise that
could have caused the driver to report an invalid NVM checksum upon
driver load.
Reported-by: NStefan Assmann <sassmann@kpanic.de>
Fixes: 96a39aed ("i40e: Acquire NVM lock before reads on all devices", 2016-12-02)
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The dynamic ITR algorithm depends on a calculation of usecs which
assumes that the interrupts have been firing constantly at the interrupt
throttle rate. This is not guaranteed because we could have a low packet
rate, or have been polling in software.

We'll estimate whether this is the case by using jiffies to determine if
we've been too long. If the time difference of jiffies is larger we are
guaranteed to have an incorrect calculation. If the time difference of
jiffies is smaller we might have been polling some but the difference
shouldn't affect the calculation too much.

This ensures that we don't get stuck in BULK latency during certain rare
situations where we receive bursts of packets that force us into NAPI
polling.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Since commit c56625d5 ("i40e/i40evf: change dynamic interrupt
thresholds") a new higher latency ITR setting called I40E_ULTRA_LATENCY
was added with a cryptic comment about how it was meant for adjusting Rx
more aggressively when streaming small packets.

This mode was attempting to calculate packets per second and then kick
in when we have a huge number of small packets.

Unfortunately, the ULTRA setting was kicking in for workloads it wasn't
intended for including single-thread UDP_STREAM workloads.

This wasn't caught for a variety of reasons. First, the ip_defrag
routines were improved somewhat which makes the UDP_STREAM test still
reasonable at 10GbE, even when dropped down to 8k interrupts a second.
Additionally, some other obvious workloads appear to work fine, such
as TCP_STREAM.

The number 40k doesn't make sense for a number of reasons. First, we
absolutely can do more than 40k packets per second. Second, we calculate
the value inline in an integer, which sometimes can overflow resulting
in using incorrect values.

If we fix this overflow it makes it even more likely that we'll enter
ULTRA mode which is the opposite of what we want.

The ULTRA mode was added originally as a way to reduce CPU utilization
during a small packet workload where we weren't keeping up anyways. It
should never have been kicking in during these other workloads.

Given the issues outlined above, let's remove the ULTRA latency mode. If
necessary, a better solution to the CPU utilization issue for small
packet workloads will be added in a future patch.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In commit 96db776a ("i40e/vf: fix interrupt affinity bug")
we added some code to force exit of polling in case we did
not have the correct CPU. This is important since it was possible for
the IRQ affinity to be changed while the CPU is pegged at 100%. This can
result in the polling routine being stuck on the wrong CPU until
traffic finally stops.

Unfortunately, the implementation, "if the CPU is correct, exit as
normal, otherwise, fall-through to the end-polling exit" is incredibly
confusing to reason about. In this case, the normal flow looks like the
exception, while the exception actually occurs far away from the if
statement and comment.

We recently discovered and fixed a bug in this code because we were
incorrectly initializing the affinity mask.

Re-write the code so that the exceptional case is handled at the check,
rather than having the logic be spread through the regular exit flow.
This does end up with minor code duplication, but the resulting code is
much easier to reason about.

The new logic is identical, but inverted. If we are running on a CPU not
in our affinity mask, we'll exit polling. However, the code flow is much
easier to understand.

Note that we don't actually have to check for MSI-X, because in the MSI
case we'll only have one q_vector, but its default affinity mask should
be correct as it includes all CPUs when it's initialized. Further, we
could at some point add code to setup the notifier for the non-MSI-X
case and enable this workaround for that case too, if desired, though
there isn't much gain since its unlikely to be the common case.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

On older kernels a call to irq_set_affinity_hint does not guarantee that
the IRQ affinity will be set. If nothing else on the system sets the IRQ
affinity this can result in a bug in the i40e_napi_poll() routine where
we notice that our interrupt fired on the "wrong" CPU according to our
internal affinity_mask variable.

This results in a bug where we continuously tell NAPI to stop polling to
move the interrupt to a new CPU, but the CPU never changes because our
affinity mask does not match the actual mask setup for the IRQ.

The root problem is a mismatched affinity mask value. So lets initialize
the value to cpu_possible_mask instead. This ensures that prior to the
first time we get an IRQ affinity notification we'll have the mask set
to include every possible CPU.

We use cpu_possible_mask instead of cpu_online_mask since the former is
almost certainly never going to change, while the later might change
after we've made a copy.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

If we don't have MSI-X enabled, we handle interrupts on all icr0. This
is a special case, so let's move the conditional into
i40e_update_enable_itr() in order to make i40e_napi_poll easier to
read about.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Since commit 3ffa037d ("i40e: Set XPS bit mask to zero in DCB mode")
we've tried to reset the XPS settings by building a custom
empty CPU mask.

This workaround is not necessary because we're not really removing the
XPS setting, but simply setting it so that no CPU is valid.

Second, we shorten the code further by using zalloc_cpumask_var instead
of a separate call to bitmap_zero().
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes an issue where an error return value is
set, but without an immediate exit, the value can be overwritten
by the following code execution.  The condition  at this point
is not fatal, so remove the error assignment and comment the
intent for future code maintainers
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch improves the system log message. The log message will
be expanded to include the FEC mode the FW requested before link
was established.
Signed-off-by: NMariusz Stachura <mariusz.stachura@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch gives VF capability to control VLAN tag stripping via
ethtool. As rx-vlan-offload was fixed before, now the VF is able to
change it using "ethtool --offload <IF> rxvlan on/off" settings.
Signed-off-by: NMariusz Stachura <mariusz.stachura@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In new versions of GCC since 7.x a new warning exists which warns when
a string is truncated before all of the format can be completed.

When we setup VMDQ netdev names we are copying a pre-existing interface
name which could be up to 15 characters in length. Since we also add
4 bytes, v, the literal %, the d and a \0 null, we would overrun the
available size unless snprintf truncated for us.

The snprintf call will of course truncate on the end, so lets instead
modify the code to force truncation of the copied netdev name by
4 characters, to create enough space for the 4 bytes we're adding.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The q_vector names are based on the interface name with a driver prefix,
the type of q_vector setup, and the queue number. We previously set the
size of this variable to IFNAMSIZ + 9, which is incorrect, because we
actually include a minimum of 14 characters extra beyond the interface
name size.

New versions of GCC since 7 include a new warning that detects this
possible truncation and complains. We can fix this by increasing the
size in case our interface name is too large to avoid truncation. We
don't need to go beyond 14 because the compiler is smart enough to
realize our values can never exceed size of 1. We do go up to 15 here
because possible future changes may increase the number of queues beyond
one digit.

While we are here, also change some variables to be unsigned (since they
are never negative) and stop using an extra unnecessary %s format
specifier.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Albeit, we usually set true promiscuous mode for both multicast and
unicast at the same time - however, it is possible to set it
individually, so using allmulti flag which is only for allmulticast might
caused unwanted behavior in mirroring egress traffic promiscuous for
unicast in VF.
Signed-off-by: NAkeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Increase the size of the prefix buffer so that it can hold enough
characters for every possible input. Although 20 is enough for all
expected inputs, it is possible for the values to be larger than
expected, resulting in a possibly truncated string. Additionally, lets
use sizeof(prefix) in order to ensure we use the correct size if we need
to change the array length in the future.

New versions of GCC starting at 7 now include warnings to prevent
truncation unless you handle the return code. At most 27 bytes can be
written here, so lets just increase the buffer size even if for all
expected hw->bus.* values we only needed 20.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Store information about FEC modes, that were requested. It will be used
in printing link status information function and this way there is no
need to call admin queue there.
Signed-off-by: NMariusz Stachura <mariusz.stachura@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

During NVM update, state machine gets into unrecoverable state because
i40e_clean_adminq_subtask can get scheduled after the admin queue
command but before other state variables are updated. This causes
incorrect input to i40e_nvmupd_check_wait_event and state transitions
don't happen.

This fix updates the state variables so that adminq_subtask will have
accurate information whenever it gets scheduled.
Signed-off-by: NSudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

During NVM update, state machine gets into unrecoverable state because
i40e_clean_adminq_subtask can get scheduled after the admin queue
command but before other state variables are updated. This causes
incorrect input to i40e_nvmupd_check_wait_event and state transitions
don't happen.

This issue existed before but surfaced after commit 373149fc
("i40e: Decrease the scope of rtnl lock")

This fix adds locking around admin queue command and update of
state variables so that adminq_subtask will have accurate information
whenever it gets scheduled.
Signed-off-by: NSudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently the driver allows the user to change (or even disable)
interrupt moderation if adaptive-rx/tx is enabled when this should
not be the case.

Adaptive RX/TX will not respect the user's ITR settings so
allowing the user to change it is weird.  This bug would also
allow the user to disable interrupt moderation with adaptive-rx/tx
enabled which doesn't make much sense either.

This patch makes it such that if adaptive-rx/tx is enabled, the user
cannot make any manual adjustments to interrupt moderation.  It also
makes it so that if ITR is disabled but adaptive-rx/tx is then
enabled, ITR will be re-enabled.
Signed-off-by: NAlan Brady <alan.brady@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

According to the header file cpumask.h, we shouldn't be directly copying
a cpumask_t, since its a bitmap and might not be copied correctly. Lets
use the provided cpumask_copy() function instead.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

If we're going to bother initializing a variable to reference it we might
as well use it.
Signed-off-by: NAlan Brady <alan.brady@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The current name of vf_offload_flags indicates that the bitmap is
limited to offload related features. Make this more generic by renaming
it to vf_cap_flags, which allows for other capabilities besides
offloading to be added.
Signed-off-by: NStefan Assmann <sassmann@kpanic.de>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In i40e_vsi_add_vlan we treat attempting to add VID=0 as an error,
because it does not do what the caller might expect. We already special
case VID=0 in i40e_vlan_rx_add_vid so that we avoid this error when
adding the VLAN.

This special casing is necessary so that we do not add the VLAN=0 filter
since we don't want to stop receiving untagged traffic. Unfortunately,
not all callers of i40e_vsi_add_vlan are aware of this, including when
we add VLANs from a VF device.

Rather than special casing every single caller of i40e_vsi_add_vlan,
lets just move this check internally. This makes the code simpler
because the caller does not need to be aware of how VLAN=0 is special,
and we don't forget to add this check in new places.

This fixes a harmless error message displaying when adding a VLAN from
within a VF. The message was meaningless but there is no reason to
confuse end users and system administrators, and this is now avoided.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When a user gives an invalid command to change a private flag which is
not supported, either because it is read-only, or the device is not
capable of the feature, we simply ignore the request.

A naive solution would simply be to report error codes when one of the
flags was not supported. However, this causes problems because it makes
the operation not atomic. If a user requests multiple private flags
together at once we could end up changing one before failing at the
second flag.

We can do a bit better if we instead update a temporary copy of the
flags variable in the loop, and then copy it into place after. If we
aren't careful this has the pitfall of potentially silently overwriting
any changes caused by other threads.

Avoid this by using cmpxchg64 which will compare and swap the flags
variable only if it currently matched the old value. We'll report
-EAGAIN in the (hopefully rare!) case where the cmpxchg64 fails.

This ensures that we can properly report when flags are not supported in
an atomic fashion without the risk of overwriting other threads changes.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes a problem with the HW ATR eviction feature where the
NVM setting was incorrect.  This patch detects the issue on X720
adapters and disables the feature if the NVM setting is incorrect.

Without this patch, HW ATR Evict feature does not work on broken NVMs
and is not detected either.  If the HW ATR Evict feature is disabled
the SW Eviction feature will take effect.
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: NAlice Michael <alice.michael@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Since commit b499ffb0 ("i40e: Look up MAC address in Open Firmware
or IDPROM"), we've had support for obtaining the MAC address
form Open Firmware or IDPROM.

This code relied on sending the Open Firmware address directly to the
device firmware instead of relying on our MAC/VLAN filter list. Thus,
a work around was introduced in commit b1b15df5 ("i40e: Explicitly
write platform-specific mac address after PF reset")

We refactored the Open Firmware address enablement code in the ill-named
commit 41c4c2b5 ("i40e: allow look-up of MAC address from Open
Firmware or IDPROM")

Since this refactor, we no longer even set I40E_FLAG_PF_MAC. Further, we
don't need this work around, because we actually store the MAC address
as part of the MAC/VLAN filter hash. Thus, we will restore the address
correctly upon reset.

The refactor above failed to revert the workaround, so do that now.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The number of flags found in pf->flags has grown quite large, and there
are a lot of different types of flags. Most of the flags are simply
hardware features which are enabled on some firmware or some MAC types.
Other flags are dynamic run-time flags which enable or disable certain
features of the driver.

Separate these two types of flags into pf->hw_features and pf->flags.
The hw_features list will contain a set of features which are enabled at
init time. This will not contain toggles or otherwise dynamically
changing features. These flags should not need atomic protections, as
they will be set once during init and then be essentially read only.

Everything else will remain in the flags variable. These flags may be
modified at any time during run time. A future patch may wish to convert
these flags into set_bit/clear_bit/test_bit or similar approach to
ensure atomic correctness.

The I40E_FLAG_MFP_ENABLED flag may be a good fit for hw_features but
currently is used by ethtool in the private flags settings, and thus has
been left as part of flags.

Additionally, I40E_FLAG_DCB_CAPABLE may be a good fit for the
hw_features but this patch has not tried to untangle it yet.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The X722 pf flag setup should happen before the VMDq RSS queue count is
initialized for VMDq VSI to get the right number of queues for RSS in
case of X722 devices.
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: NAlice Michael <alice.michael@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently i40evf_close() can return before state transitions to
__I40EVF_DOWN because of the latency involved in processing and
receiving response from PF driver and scheduling of VF watchdog_task.
Due to this inconsistency an immediate call to i40evf_open() fails
because state is still DOWN_PENDING.

When a VF interface is in up state and we try to add it as slave,
The bonding driver calls dev_close() and dev_open() in short duration
resulting in dev_open returning error. The ifenslave command needs
to be run again for dev_open to succeed.

This fix ensures that watchdog timer is scheduled immediately after
admin queue operations are scheduled in i40evf_down(). In addition a
wait condition is added at the end of i40evf_close so that function
wont return when state is still DOWN_PENDING. The timeout value is
chosen after some profiling and includes some buffer.
Signed-off-by: NSudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Now that the kernel supports double VLAN tags, we should at least play
nice. Adjust the max packet size to account for two VLAN tags, not just
one.
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

For XDP_REDIRECT the use of return code -EINVAL is confusing, as it is
used in three different cases.  (1) When the index or ifindex lookup
fails, and in the ixgbe driver (2) when link is down and (3) when XDP
have not been enabled.

The return code can be picked up by the tracepoint xdp:xdp_redirect
for diagnosing why XDP_REDIRECT isn't working.  Thus, there is a need
different return codes to tell the issues apart.

I'm considering using a specific err-code scheme for XDP_REDIRECT
instead of using these errno codes.
Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use errno -ENOSPC ("No space left on device") when the XDP xmit
have no space left on the TX ring buffer, instead of -ENOMEM.
Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com>
Acked-by: NJohn Fastabend <john.fastabend@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The offending commit used a newly added helper function.
But the logic is wrong. Without this fix, the affected NICs
can't do HW offload. Error -EOPNOTSUPP will be returned directly.

Fixes: a2e8da93 ("net/sched: use newly added classid identity helpers")
Signed-off-by: NChris Mi <chrism@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>