This patch adds initialization of the Touchscreen controller for the
AT91SAM9RL processor.
Signed-off-by: NJustin Waters <justin.waters@timesys.com>
Signed-off-by: NDan Liang <dan.liang@atmel.com>
Signed-off-by: NAndrew Victor <linux@maxim.org.za>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Use the PWM controller and leds-atmel-pwm.c driver to drive a LED on
the Atmel AT91SAM9263-EK board.
Signed-off-by: NSedji Gaouaou <sedji.gaouaou@atmel.com>
Signed-off-by: NAndrew Victor <linux@maxim.org.za>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add platform_devices and configuration of the PWM controller found on
Atmel AT91CAP9, SAM9263 and SAM9RL processors.
SAM9263 support by Sedji Gaouaou.
Signed-off-by: NAndrew Victor <linux@maxim.org.za>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This just leaves include/asm-arm/plat-* to deal with.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Support for the at91sam9g20 : Atmel 400Mhz ARM 926ej-s SOC.

AT91sam9g20 is an evolution of the at91sam9260 with a faster clock
speed.
We created a new board for this device but based the chip support
directly on 9260 files with little updates.
Here is the chip page on Atmel wabsite:
http://atmel.com/dyn/products/product_card.asp?part_id=4337Signed-off-by: NSedji Gaouaou <sedji.gaouaou@atmel.com>
Signed-off-by: NJustin Waters <justin.waters@timesys.com>
Acked-by: NAndrew Victor <linux@maxim.org.za>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This is basically s/at91_nand/atmel_nand/g with some manual inspection.
Signed-off-by: NHåvard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

This is patch 1 of 2 adding support for the USB High Speed Device Port
on the AT91CAP9 system on chip. The AT91CAP9 uses the same UDPHS IP
as the AVR32 and the AT91SAM9RL.

This patch makes the generic AT91 adaptations, mainly dealing with
the addition of the UDPHS UTMI clock.
Signed-off-by: NStelian Pop <stelian@popies.net>
Acked-by: NHaavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: NAndrew Victor <linux@maxim.org.za>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Various small at91_udc cleanups:

 - Use generic GPIO calls, not older platform-specific ones
 - Use gpio_request()/gpio_free()
 - Use VERBOSE_DEBUG convention, not older VERBOSE
 - Fix sparse complaint about parameter type (changed to gfp_t)
 - Add missing newline to some rarely-seen debug messages
 - Fix some old cleanup bugs on probe() fault paths

Also add a mechanism whereby rm9200 gpios can drive the D+ pullup
through an inverting transistor, based on a patch from Steve Birtles.
Most UDC drivers supporting a GPIO based pullup should probably have
such an option, but testing it requries such a board in hand!
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Cc: Steve Birtles <arm_kernel_development@micromark.net.cn>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add support for Atmel's AT91CAP9 Customizable Microcontroller family.
  <http://www.atmel.com/products/AT91CAP/Default.asp>
Signed-off-by: NStelian Pop <stelian@popies.net>
Signed-off-by: NAndrew Victor <linux@maxim.org.za>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Move the LED initialization code out of the various *_devices.c files,
and into leds.c.
Also add support for NEW_LEDs.

Patch from David Brownell.
Signed-off-by: NAndrew Victor <linux@maxim.org.za>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Modify the UART initialization to allow the board-initialization code
to specify which pins are connected, and which pins should therefore
be initialized.

The current at91_init_serial() will continue to work as-is, but is
marked as "deprecated" and will be removed once the board-specific
files has been updated to use the new interface.

As in the AVR32 code, we assume that the TX and RX pins will always be
initialized.
Signed-off-by: NAndrew Victor <linux@maxim.org.za>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Core support of the Atmel SSC library for all Atmel AT91 processors.

Based on David Brownell's initial patch for the AT91RM9200.
Signed-off-by: NAndrew Victor <linux@maxim.org.za>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add support for the Image Sensor Interface (ISI) peripheral integrated
in the Atmel AT91SAM9263 processor.

Patch from MaLiK
Signed-off-by: NAndrew Victor <linux@maxim.org.za>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The AT91 I2C driver is currently marked as "broken" due to hardware
issues.  This patch enables AT91-based platforms to also use the
bitbanged GPIO for I2C.

This updates platform setup logic (setting up an i2c-gpio device
using the same pins as the i2c-at91 device, unless only the BROKEN
driver is enabled).

Also make use of the new-style initialization of I2C devices using
i2c_register_board_info().
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Fix:

  CC      drivers/serial/atmel_serial.o
drivers/serial/atmel_serial.c: In function 'atmel_serial_suspend':
drivers/serial/atmel_serial.c:924: error: implicit declaration of function 'at91_suspend_entering_slow_clock'
Acked-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Convert the macb driver to use the generic PHY layer in
drivers/net/phy.
Signed-off-by: NFrederic RODO <f.rodo@til-technologies.fr>
Signed-off-by: NHaavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Fix a build error due to a missing semicolon.
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Define resources, platform_device and device registration functions for
the LCD and AC97 controllers on the AT91SAM9263.
Also update the AT91SAM9261 to use the common atmel_lcdfb driver.
Signed-off-by: NNicolas Ferre <nicolas.ferre@rfo.atmel.com>
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The Atmel AT91SAM9263 processor includes many more integrated
peripherals than Atmel's previous ARM9-based AT91 processors, so this
has necessitated a few changes to the core AT91 support.

These changes are:
      * The system peripheral I/O region we remap has increased from
        0xFFFA0000..0xFFFFFFFF to 0xFFF78000..0xFFFFFFFF.
      * The increased I/O region forces changes to entry-macro.S and
        debug-macro.S due to ARM's limited immediate offset addressing
        modes.
      * Maximum number of GPIO banks increases to 5.
      * 2 MMC controllers so the board-setup code needs to specify which
        controller it wishes to use when calling at91_add_device_mmc().

Original patch from Nicolas Ferre.
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Now that Linux includes support for the Atmel AT91SAM9260 and
AT91SAM9261 processors in addition to the original Atmel AT91RM9200
(with support for more AT91 processors pending), the "mach-at91rm9200"
and "arch-at91rm9200" directories should be renamed to indicate their
more generic nature.

The following git commands should be run BEFORE applying this patch:
  git-mv arch/arm/mach-at91rm9200 arch/arm/mach-at91
  git-mv include/asm-arm/arch-at91rm9200 include/asm-arm/arch-at91
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Fix build failure of AT91SAM9260.

The AT91RM9200 ethernet driver (at91_ether.c) stores platform data in a
"struct at91_eth_data" structure, but the AT91SAM9260 (and AT91SAM9263)
ethernet driver (macb.c) [developed on the AVR32 architecture] expects a
"struct eth_platform_data".

Since the platform data of the two drivers is very similar, we continue
to use the "struct at91_eth_data" for all AT91 processors but add a
    #define eth_platform_data      at91_eth_data
in board.h to keep the MACB driver happy.

Original patch by Jan Altenberg.
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Replace the 'is_b' variable with 'slot_b' in at91_mmc_data.
Also add the new 'chipselect' variable for CF/PCMCIA and 'bus_width_16'
variable for NAND.

This (and previous patches) will unfortunately break the current MMC,
USB Gadget and PCMCIA drivers.  Updates and fixes for those drivers will
be submitted to the various subsystem maintainers.
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

In order to initialize the serial console early, the atmel_serial
driver had to do a hack where it compared the physical address of the
port with an address known to be permanently mapped, and used it as a
virtual address. This got around the limitation that ioremap() isn't
always available when the console is being initalized.

This patch removes that hack and replaces it with a new "regs" field
in struct atmel_uart_data that the board-specific code can initialize
to a fixed virtual mapping for platform devices where this is possible.
It also initializes the DBGU's regs field with the address the driver
used to check against.

On AVR32, the "regs" field is initialized from the physical base
address when this it can be accessed through a permanently 1:1 mapped
segment, i.e. the P4 segment.

If regs is NULL, the console initialization is delayed until the "real"
driver is up and running and ioremap() can be used.
Signed-off-by: NHaavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Rename the following public definitions:
  * AT91_NR_UART -> ATMEL_MAX_UART
  * struct at91_uart_data -> struct atmel_uart_data
  * at91_default_console_device -> atmel_default_console_device
Signed-off-by: NHaavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Signed-off-by: NAdrian Bunk <bunk@stusta.de>

Patch from Andrew Victor

This patch removes some now unnecessary global variables -
at91_master_clock, at91_serial_map, at91_console_port.
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Andrew Victor

This patch includes the structures and exported functions required for
the platform-device support (added in patch 3585/1).

Also adds the arch_identify() function for run-time detection of which
AT91 processor the code is running on.  [Original patch from Ivan
Kokshaysky]
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Andrew Victor

This patch updates the platform device resources for the Ethernet and
MMC peripherals.  It also adds platform device information for the NAND
(SmartMedia), I2C and the RTC.

(This version of the patch can be applied before Patch 3392/1)
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Andrew Victor

This patch adds support for the LED(s) on the AT91RM9200-based boards.

(This version of the patch can be applied before Patch 3392/1)
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from SAN People

Following changes were made to clock.c:

1) Replaced <asm/hardware/clock.h> with <linux/clk.h>
2) Removed old unused clk_enable & clk_disable.
3) Replaced clk_use/clk_unuse with clk_enable/clk_disable.

Otherwise it's the same as the previous patch.
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>