Add IV-room in skb also for TKIP and WEP.
Extend patch: "mac80211: support adding IV-room in the skb for CCMP keys"
Signed-off-by: NJanusz Dziedzic <janusz.dziedzic@tieto.com>
Acked-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In commit 12d3952f
("mac80211: optimize aggregation session timeout handling")
two bugs were introduced:
 1) RCU usage was completely broken since no locks are held
 2) the timer must not rearm when agg session is stopping
Reported-and-tested-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

My queue management rework broke drivers that don't
have multiple AC queues and register a single queue
only, causing a warning:

WARNING: at net/mac80211/iface.c:162 ieee80211_check_queues

This was due to filling the queues wrongly and then
noticing the error when checking later.
Reported-and-Tested-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Forwarded PREQ is either unicast or multicast. The appropriate counters
should be incremented accordingly.
Signed-off-by: NChun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Only send a cfg80211 new peer candidate notification if userspace has
yet to allocate this station entry.
Signed-off-by: NThomas Pedersen <thomas@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch introduces a new mesh configuration parameter "ht_opmode" and will
allow user to check the current HT protection mode selected. Users could
configure the protection mode by the command "iw mesh_iface set mesh_param
mesh_ht_protection_mode=2". The default protection mode of mesh is set to
non-HT mixed mode.
Signed-off-by: NAshok Nagarajan <ashok@cozybit.com>
Reviewed-by: NThomas Pedersen <thomas@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Now that we have protection enabled, allow non-HT and HT20 stations to peer
with HT40+/- stations. Peering is still disallowed for HT40+/- mismatch.
Signed-off-by: NAshok Nagarajan <ashok@cozybit.com>
Reviewed-by: NThomas Pedersen <thomas@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Section 9.23.3.5 of IEEE 80211s standard describes the protection rules for
HT mesh STA in a MBSS. Three HT protection modes are supported for now:

non-HT mixed mode - is selected if any non-HT peers are present in our MBSS.
20MHz-protection mode - is selected if all peers in our 20/40MHz MBSS support
			HT and atleast one HT20 peer is present.
no-protection mode - is selected otherwise.

This is a limited implementation of 9.23.3.5, which only considers mesh peers
when determining the HT protection mode. Station's channel_type needs to be
maintained.
Signed-off-by: NAshok Nagarajan <ashok@cozybit.com>
Reviewed-by: NThomas Pedersen <thomas@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NAshok Nagarajan <ashok@cozybit.com>
Reviewed-by: NThomas Pedersen <thomas@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The signal and noise are forced to be positive since ethtool
deals in unsigned 64-bit values and this number should be human
readable.  This gives easy access to some of the data formerly
exposed in the deprecated /proc/net/wireless file.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This adds hooks to call into the driver to get additional
stats for the ethtool API.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This lets ethtool print out stats related to stations
connected to the interface.  Does not yet get stats
from the underlying driver.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If a mesh peer indicates it is operating as 20MHz-only in its HT
operation IE, have the rate control algorithm respect this by disabling
the equivalent bit in the ieee80211_sta HT capabilities.
Signed-off-by: NThomas Pedersen <thomas@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Drivers need the station rate info when inserting a new sta_info. The
patch "mac80211: refactor mesh peer initialization" wrongly assumed the
rate info could be applied after insertion. After further review, this
is clearly not the case.

This fixes a regression where HT parameters were not applied before
inserting the sta_info, causing performance degradation.
Signed-off-by: NThomas Pedersen <thomas@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The rate control updation never be called on 2040 BSS change.
The station should update its rate control on receiving beacon
with different HT mode in the HT operation IE. Not doing so,
leads to sending frames with higher(ht40) rates whereas AP is
operating in lower mode (ht20).
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

EAP frames for stations in an AP VLAN are sent on the main AP interface
to avoid race conditions wrt. moving stations.
For that to work properly, sta_info_get_bss must be used instead of
sta_info_get when sending EAP packets.
Previously this was only done for cooked monitor injected packets, so
this patch adds a check for tx->skb->protocol to the same place.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Adds hepler to clean sdata ieee80211_clean_sdata similar way as
ieee80211_setup_sdata is implemented. The function will be used by other
interfaces later.
Signed-off-by: NAndrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Moving a STA to an AP VLAN prevents num_mcast_sta from being decremented
once the STA leaves, because sta->sdata changes. Fix this by checking
for AP VLANs as well.

Also exclude 4-addr VLAN stations from num_mcast_sta - remote 4-addr
stations ignore 3-address multicast frames anyway. In a typical bridge
configuration they receive the same packets as 4-address unicast.

This patch also fixes clearing the sdata->u.vlan.sta pointer when the
STA is removed from a 4-addr VLAN.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It is only used to test for BSS multicast receivers.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Reviewed-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Average beacon signal only keep tracked by managed interface,
give warning and return 0 for the others.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ieee80211_mgd_teardown() is called on netdev removal, which
occurs after the vif was already removed from the low-level
driver, resulting in the following warning:

[ 4809.014734] ------------[ cut here ]------------
[ 4809.019861] WARNING: at net/mac80211/driver-ops.h:12 ieee80211_bss_info_change_notify+0x200/0x2c8 [mac80211]()
[ 4809.030388] wlan0:  Failed check-sdata-in-driver check, flags: 0x4
[ 4809.036862] Modules linked in: wlcore_sdio(-) wl12xx wlcore mac80211 cfg80211 [last unloaded: cfg80211]
[ 4809.046849] [<c001bd4c>] (unwind_backtrace+0x0/0x12c)
[ 4809.055937] [<c047cf1c>] (dump_stack+0x20/0x24)
[ 4809.065385] [<c003e334>] (warn_slowpath_common+0x5c/0x74)
[ 4809.075589] [<c003e408>] (warn_slowpath_fmt+0x40/0x48)
[ 4809.088291] [<bf033630>] (ieee80211_bss_info_change_notify+0x200/0x2c8 [mac80211])
[ 4809.102844] [<bf067f84>] (ieee80211_destroy_auth_data+0x80/0xa4 [mac80211])
[ 4809.116276] [<bf068004>] (ieee80211_mgd_teardown+0x5c/0x74 [mac80211])
[ 4809.129331] [<bf043f18>] (ieee80211_teardown_sdata+0xb0/0xd8 [mac80211])
[ 4809.141595] [<c03b5e58>] (rollback_registered_many+0x228/0x2f0)
[ 4809.153056] [<c03b5f48>] (unregister_netdevice_many+0x28/0x50)
[ 4809.165696] [<bf041ea8>] (ieee80211_remove_interfaces+0xb4/0xdc [mac80211])
[ 4809.179151] [<bf032174>] (ieee80211_unregister_hw+0x50/0xf0 [mac80211])
[ 4809.191043] [<bf0bebb4>] (wlcore_remove+0x5c/0x7c [wlcore])
[ 4809.201491] [<c02c6918>] (platform_drv_remove+0x24/0x28)
[ 4809.212029] [<c02c4d50>] (__device_release_driver+0x8c/0xcc)
[ 4809.222738] [<c02c4e84>] (device_release_driver+0x30/0x3c)
[ 4809.233099] [<c02c4258>] (bus_remove_device+0x10c/0x128)
[ 4809.242620] [<c02c26f8>] (device_del+0x11c/0x17c)
[ 4809.252150] [<c02c6de0>] (platform_device_del+0x28/0x68)
[ 4809.263051] [<bf0df49c>] (wl1271_remove+0x3c/0x50 [wlcore_sdio])
[ 4809.273590] [<c03806b0>] (sdio_bus_remove+0x48/0xf8)
[ 4809.283754] [<c02c4d50>] (__device_release_driver+0x8c/0xcc)
[ 4809.293729] [<c02c4e2c>] (driver_detach+0x9c/0xc4)
[ 4809.303163] [<c02c3d7c>] (bus_remove_driver+0xc4/0xf4)
[ 4809.312973] [<c02c5a98>] (driver_unregister+0x70/0x7c)
[ 4809.323220] [<c03809c4>] (sdio_unregister_driver+0x24/0x2c)
[ 4809.334213] [<bf0df458>] (wl1271_exit+0x14/0x1c [wlcore_sdio])
[ 4809.344930] [<c009b1a4>] (sys_delete_module+0x228/0x2a8)
[ 4809.354734] ---[ end trace 515290ccf5feb522 ]---

Rename ieee80211_mgd_teardown() to ieee80211_mgd_stop(),
and call it on ieee80211_do_stop().
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ieee80211_ave_rssi need to be declare as export for driver to use it.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The original patch defined the correction margin but did not apply it.
Signed-off-by: NShinichi Hotori <hotorinn@gmail.com>
Signed-off-by: NYu Niiro <yu.niiro@gmail.com>
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

According to IEEE 802.11 8.4.2.59, set the "STA channel width" bit to 0
if transmitting STA is using a 20mhz channel.
Signed-off-by: NThomas Pedersen <thomas@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Blindly setting ht caps on a mesh peer's station entry would result in
MCS rates being used by the rate control algorithm even if no ht had
been configured. Fix this by checking the channel type before assigning
ht capabilites.
Signed-off-by: NThomas Pedersen <thomas@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

To avoid passing supp_rates and basic_rates around all the time, just
derive these when needed in mesh_matches_local() and mesh_peer_init().
Signed-off-by: NThomas Pedersen <thomas@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch unifies the previous two paths toward mesh peer creation a
bit. It also fixes a bug where a peer's changing rates or HT mode
wouldn't register on leaving and then returning to the mesh with a sta
entry still present.

Also clean up locking and clear possibly stale ht cap.
Signed-off-by: NThomas Pedersen <thomas@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This based on an idea posted by Stanislaw Gruszka,
though I accept full blame for the implementation!

This has been tested with ath9k.

The idea is to let users scan on the current operating
channel without interrupting normal traffic more than
absolutely necessary (changing power level might reset
some hardware, for instance).
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The broken check leads to rate control attempting to use HT40 while
the driver is configured for HT20. This leads to interesting hardware
issues.

HT40 can only be used if the channel type is either HT40- or HT40+
and if the channel type of the cell matches the local type.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Cooked monitor rx was recently changed to use ieee80211_add_rx_radiotap_header
instead of generating only limited radiotap information.
ieee80211_add_rx_radiotap_header assumes that FCS info is still present if
the hardware supports receiving it, however when cooked monitor rx packets
are processed, FCS info has already been stripped.
Fix this by adding an extra flag indicating FCS presence.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add utility function to provide the average rssi per vif
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When testing mesh synchronization we observed a global TSF slowdown that
was dependent on the number of synchronized mesh stations.  This seems
to be caused by the TSF adjustment (read/write) latency.

Adding a small margin to the Toffset setpoint solved the problem.
Signed-off-by: NShinichi Hotori <hotorinn@gmail.com>
Signed-off-by: NYu Niiro <yu.niiro@gmail.com>
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Commit 3a25a8c8 (mac80211: add improved HW queue control) introduced a
bug when running in AP mode without the IEEE80211_HW_QUEUE_CONTROL
flag set.  The ieee80211_check_queues() function always returns
-EINVAL, preventing AP mode from starting.  To fix this, check whether
this flag is set before checking if cab_queue is set properly.
Signed-off-by: NLuciano Coelho <coelho@ti.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

its not used where, while we directly obtain ieee80211_bss's
pointer in ibss.c by calling cfg80211_get_bss
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Removes hw.conf.channel usage from the following functions:
 * ieee80211_mandatory_rates
 * ieee80211_sta_get_rates
 * ieee80211_frame_duration
 * ieee80211_rts_duration
 * ieee80211_ctstoself_duration

This is in preparation for multi-channel operation.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

I noticed a possible issue in the status count field management of the
ieee80211_tx_info data structure. In particular, when the AGGR
processing is employed,
status.rates[].count is set just for the first frame and not for
others belonging to the same burst, leading to wrong statistic data in
the mac80211 debug file system.
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If the current channel is known, add frequency and channel type to
NL80211_CMD_GET_INTERFACE.
Signed-off-by: NPontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Before we send probes in connection monitoring we check if scan is not
pending. But we do that check without locking. Fix that and also do not
start scan if connection monitoring is in progress.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>