By putting the maximum frame size supported by the hardware into the
adapter structure, the change_mtu entry point function can be cleaned
up of checks for all the different max frame sizes supported by
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The flow control thresholds, i.e. high and low watermarks of the Rx
FIFO for when the hardware should transmit PAUSE frames (XON and XOFF,
respectively), need to be tuned for more efficient use of the FIFO.
The logic to set the thresholds for parts that support early-receive
(ERT) was also wrong in that it should check whether jumbo frames are
in use.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

During reset, the driver was attempting to disable the Smart Powerdown
feature even if the part does not support Smart Powerdown.  Check for
support before attempting to disable the feature.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Second round of drivers for Gb cards (and NIU one I forgot in the 10GB round)

Now that core network takes care of trans_start updates, dont do it
in drivers themselves, if possible. Drivers can avoid one cache miss
(on dev->trans_start) in their start_xmit() handler.

Exceptions are NETIF_F_LLTX drivers
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

after the recent changes to wired drivers to use only
netif_carrier_off the driver can have outstanding tx work to
complete that will never complete once link is down.  Since the
intel hardware will hold this tx work forever, the driver
notices a tx timeout condition internally and might try
to instigate printk and reset of the part with a
netif_stop_queue, which doesn't work because link is down.

Don't bother arming to tx hang detection when link is down.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It was pointed out that the Intel wired ethernet drivers do not need to
wake the tx queue since netif_carrier_on/off will take care of the qdisc
management in order to guarantee the correct handling of the transmit
routine enable state.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As reported by Andrew Lutomirski <amluto@gmail.com>

All the intel wired ethernet drivers were calling netif_carrier_off
and netif_stop_queue (or variants) before calling register_netdevice

This is incorrect behavior as was pointed out by davem, and causes
ifconfig and friends to report a strange state before first link
after the driver was loaded, since without a netif_carrier_off, the stack
assumes carrier_on, but before register_netdev, netlink messages are not
sent out telling link state.

This apparently confused *some* versions of networkmanager.

Andy tested this for e1000e and confirmed it was working for him.

see thread: http://marc.info/?l=linux-netdev&m=123946479705636&w=2Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAndy Lutomirski <amluto@gmail.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the e1000e transmit cleanup inner loop exited early, then
cleaned might not be true.  This could cause tx hangs or other
badness.  Use count to track the total number of descriptors
cleaned instead of basing a tx queue restart off of a temporary
working state variable.

This code now makes the flow the same for e1000/e1000e/igb/ixgbe
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Prevent e1000e from putting the adapter into D3 during shutdown except when
we're going to power off the system, since doing that may generally cause
problems with kexec to happen (such problems were observed for igb and
forcedeth).  For this purpose seperate e1000e_shutdown() from e1000e_suspend()
and use the appropriate PCI PM callbacks in both of them.
Signed-off-by: N"Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

e1000/e1000e compile report a possible unused variable, fix
that for now.  Shortly after this a small refactor and bug
fix will follow in the same code.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)

Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Replace all DMA_64BIT_MASK macro with DMA_BIT_MASK(64)

Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As noticed by Alan Cox, it is possible for e1000e to exit its interrupt
handler or NAPI with interrupts enabled even when the driver is unloading or
being configured administratively down.

fix related to fix for: http://bugzilla.kernel.org/show_bug.cgi?id=12876Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
CC: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This change updates the e1000e tx cleanup routine to more closely match
what already exists in igb and e1000.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add device ID for a new variant of the 82574 adapter.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Acked-by: NJohn Ronciak <john.ronciak@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When merging into Jeff's tree:

	commit 5f66f208
	Author: Arthur Jones <ajones@riverbed.com>
	Date:   Thu Mar 19 01:13:08 2009 +0000

	    e1000e: allow tx of pre-formatted vlan tagged packets

We lost one line, this fixes that missing
piece...
Signed-off-by: NArthur Jones <ajones@riverbed.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As with igb, when the e1000e driver is fed 802.1q
packets with hardware checksum on, it chokes with an
error of the form:

checksum_partial proto=81!

As the logic there was not smart enough to look into
the vlan header to pick out the encapsulated protocol.

There are times when we'd like to send these packets
out without having to configure a vlan on the interface.
Here we check for the vlan tag and allow the packet to
go out wiht the correct hardware checksum.

Thanks to Kand Ly <kand@riverbed.com> for discovering the
issue and the coming up with a solution.  This patch is
based upon his work.

Fixups from Stephen Hemminger <shemminger@vyatta.com> and
Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NArthur Jones <ajones@riverbed.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Stephen Hemminger <shemminger@vyatta.com>
CC: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There were a few issues I noticed in e1000e. These include a double free
of the skb if mapping fails, and the fact that context descriptors appear
to be left in the descriptor ring after the failure.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add device ID and related support for 82583 mac.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Acked-by: NRadheka Godse <radheka.godse@intel.com>
Acked-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is in reference to https://bugzilla.redhat.com/show_bug.cgi?id=484494
Also addresses issue show in kerneloops

The e1000e transmit code was calling pci_unmap_page on dma handles that it
might have called pci_map_single on.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

During the move of support for PCIe devices from e1000 to e1000e, this
workaround necessary only for older non-PCIe devices was mistakenly
copied into e1000e.  Remove it.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

RXSEQ interrupts were used to force link state interrogation of serdes
links, as the Si was not guaranteed to report LSC interrupts when the
link changed state. On some bladeservers this resulted in false link up
reports if no link partner was connected. The RXSEQ treatment is
not necessary, as the link can be monitored from the watchdog timer, and
the false link indications cease.
Signed-off-by: Ndave graham <david.graham@intel.com>
Acked-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

most if not all of the devices supported by e1000e support
AER (Advanced Error Reporting) so we attempt to register
with the OS that we know how to reset ourselves after
a fatal error.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Base versions handle constant folding now.
Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

LLTX is deprecated and complicated, don't use it.  It was observed by Don Ash
<donash4@gmail.com> that e1000e was acquiring this lock in the NAPI cleanup
path.  This is obviously a bug, as this is a leftover from when e1000
supported multiple tx queues and fake netdevs.

another user reported this to us and tested routing with the 2.6.27 kernel and
this patch and reported a 3.5 % improvement in packets forwarded in a
multi-port test on 82571 parts.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that VLAN has GRO support as well, we can call its GRO handler
as well.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Following the removal of the unused struct net_device * parameter from
the NAPI functions named *netif_rx_* in commit 908a7a16, they are
exactly equivalent to the corresponding *napi_* functions and are
therefore redundant.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Device drivers that use pci_request_regions() (and similar APIs) have a
reasonable expectation that they are the only ones accessing their device.
As part of the e1000e hunt, we were afraid that some userland (X or some
bootsplash stuff) was mapping the MMIO region that the driver thought it
had exclusively via /dev/mem or via various sysfs resource mappings.

This patch adds the option for device drivers to cause their reserved
regions to the "banned from /dev/mem use" list, so now both kernel memory
and device-exclusive MMIO regions are banned.
NOTE: This is only active when CONFIG_STRICT_DEVMEM is set.

In addition to the config option, a kernel parameter iomem=relaxed is
provided for the cases where developers want to diagnose, in the field,
drivers issues from userspace.
Reviewed-by: NMatthew Wilcox <willy@linux.intel.com>
Signed-off-by: NArjan van de Ven <arjan@linux.intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

When the napi api was changed to separate its 1:1 binding to the net_device
struct, the netif_rx_[prep|schedule|complete] api failed to remove the now
vestigual net_device structure parameter.  This patch cleans up that api by
properly removing it..
Signed-off-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds GRO support to e1000e by making it invoke napi_gro_receive
instead of netif_receive_skb.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change interrupt vector naming to match recent changes from Robert Olsson.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Acked-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

remove redundant argument comments in files of drivers/net/*
Signed-off-by: NQinghuang Feng <qhfeng.kernel@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Check return code for all NVM accesses[1] and error out accordingly; log
a debug message for failed accesses.

For ICH8/9, the valid NVM bank detect function was not checking whether the
SEC1VAL (sector 1 valid) bit in the EECD register was itself valid (bits 8
and 9 also have to be set).  If invalid, it would have defaulted to the
possibly invalid bank 0.  Instead, try to use the valid bank detection
method used by ICH10 which has been cleaned up a bit.

[1] - reads and updates only; not writes because those are only writing to
the Shadow RAM, the update following the write is the only thing actually
writing the modified Shadow RAM contents to the NVM.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On 82571 with SerDes, the true link state is not always correct when read
from the STATUS register; use existing e1000_has_link() function instead.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Rather than reading the NVM to get the EEPROM version number everytime the
ethool get_drvinfo function is called, read it once during probe and save
it for future reference.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Sync flow control variables and usage model with that found in the ixgbe
driver.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The system log messages created on a link status change need to follow a
specific format to work with tools some customers use.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On ESB2, the MAC-to-PHY (Kumeran) interface must be configured after link
is up before any traffic is sent; a new PHY operations function pointer is
provided for this.  To facilitate read/write of the Kumeran registers
without blocking PHY register writes, the driver/firmware synchronization
method which previously used a hardware semaphore for both PHY and Kumeran
register accesses is now split.  New Kumeran register read/write functions
utilize this new synchronization method.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Check return of pci_save_state and error out accordingly.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>