no-one use it and it's nearly impossible get a board to work on it
and the Mainline implementation was never finished
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Patrice Vilchez <patrice.vilchez@atmel.com>
Cc: Andrew Victor <linux@maxim.org.za>

select ARM_PATCH_PHYS_VIRT
as with ARM_PATCH_PHYS_VIRT you can patch boot_params at runtime or any recent
bootloader will provide a valid atags pointer in r2

as point out by Russell on AT91 we never use XIP
so se do not need PLAT_PHYS_OFFSET
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Patrice Vilchez <patrice.vilchez@atmel.com>
Cc: Andrew Victor <linux@maxim.org.za>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Patrice Vilchez <patrice.vilchez@atmel.com>
Cc: Andrew Victor <linux@maxim.org.za>

Add support for the Atmel AT572D940HF processor (DIOPSIS range).
This processor integrates an ARM926 core, a DSP and the SoC
peripherals usually found on an AT91 processor (USART, SSC, SPI, TWI,
CAN, etc)
Signed-off-by: NAntonio R. Costa <costa.antonior@gmail.com>
Signed-off-by: NAndrew Victor <linux@maxim.org.za>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

From: Hong Xu <hong.xu@atmel.com>

AT91sam9g10 is an ARM 926ej-s SOC. It is an evolution of the at91sam9261 with a
faster clock speed: 266/133MHz.

Here is the basic header file support for this product.
Signed-off-by: NHong Xu <hong.xu@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: NAndrew Victor <linux@maxim.org.za>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

AT91sam9g45 series is an ARM 926ej-s SOC family clocked at 400/133MHz.
It embedds USB high speed host and device, LCD, DDR2 RAM, and a full set of
peripherals.

Here is the basic header file support for this product series.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: NAndrew Victor <linux@maxim.org.za>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This just leaves include/asm-arm/plat-* to deal with.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Support for the at91sam9g20 : Atmel 400Mhz ARM 926ej-s SOC.

AT91sam9g20 is an evolution of the at91sam9260 with a faster clock
speed.
We created a new board for this device but based the chip support
directly on 9260 files with little updates.
Here is the chip page on Atmel wabsite:
http://atmel.com/dyn/products/product_card.asp?part_id=4337Signed-off-by: NSedji Gaouaou <sedji.gaouaou@atmel.com>
Signed-off-by: NJustin Waters <justin.waters@timesys.com>
Acked-by: NAndrew Victor <linux@maxim.org.za>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add support for Atmel's AT91CAP9 Customizable Microcontroller family.
  <http://www.atmel.com/products/AT91CAP/Default.asp>
Signed-off-by: NStelian Pop <stelian@popies.net>
Signed-off-by: NAndrew Victor <linux@maxim.org.za>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Modify the common at91 hardware support to deal with the non-MMU
at91x40 family. The base RAM (which is most likely not DRAM) is
set to the configured value. Virtual IO device mapping is set
to be 1 to 1 with the physical addresses.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>
Acked-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add support for Atmel's new AT91SAM9RL range of processors.
Includes similar peripherals as other AT91SAM9 processors, but with a
High-speed USB controller and various sizes of internal SRAM.
Signed-off-by: NNicolas Ferre <nicolas.ferre@rfo.atmel.com>
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Resolve the circular dependency in the AT91 header files (io.h and
hardware.h) by moving the at91_sys_read() and at91_sys_write() functions
to io.h
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The duplicate file "include/asm-arm/arch-at91rm9200/entry-macro.S" can
be removed - it was already moved to include/asm-arm/arch-at91/.

Fix 3 small typo's - two in comments, and the incorrect clock was
specified for the LCD device.
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add support for the Atmel AT91SAM9263 processor.  It is similar to the
AT91SAM9260 but with more integrated peripherals, 5 GPIO banks, etc.

Original patch from Nicolas Ferre.
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The Atmel AT91SAM9263 processor includes many more integrated
peripherals than Atmel's previous ARM9-based AT91 processors, so this
has necessitated a few changes to the core AT91 support.

These changes are:
      * The system peripheral I/O region we remap has increased from
        0xFFFA0000..0xFFFFFFFF to 0xFFF78000..0xFFFFFFFF.
      * The increased I/O region forces changes to entry-macro.S and
        debug-macro.S due to ARM's limited immediate offset addressing
        modes.
      * Maximum number of GPIO banks increases to 5.
      * 2 MMC controllers so the board-setup code needs to specify which
        controller it wishes to use when calling at91_add_device_mmc().

Original patch from Nicolas Ferre.
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Now that Linux includes support for the Atmel AT91SAM9260 and
AT91SAM9261 processors in addition to the original Atmel AT91RM9200
(with support for more AT91 processors pending), the "mach-at91rm9200"
and "arch-at91rm9200" directories should be renamed to indicate their
more generic nature.

The following git commands should be run BEFORE applying this patch:
  git-mv arch/arm/mach-at91rm9200 arch/arm/mach-at91
  git-mv include/asm-arm/arch-at91rm9200 include/asm-arm/arch-at91
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch includes a number of small changes for integrating the
AT91SAM9261 and AT91SAM0260 support.

      * Can only select support for one AT91 processor at a time.
      * Remove most of the remaining static memory mapping for the
        AT91RM9200.
      * Reserve 1Mb of memory below the IO for mapping the internal SRAM
        and any custom board-specific devices (ie, FPGA).
      * The SAM9260 has more serial ports, so increase the maximum to 7.
      * Define the standard chipselect addresses, and define other
        addresses relative to those.
      * CLOCK_TICK_RATE is different on the SAM926x's.
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch updates the drivers (and other files) which include the
hardware headers.  This fixes the breakage introduced in patches 3950/1
and 3951/1 (those patches were getting big).

The AVR32 architecture uses the same serial driver and had its own copy
of at91rm9200_pdc.h.  Renamed it to at91_pdc.h
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Rename the following public definitions:
  * AT91_NR_UART -> ATMEL_MAX_UART
  * struct at91_uart_data -> struct atmel_uart_data
  * at91_default_console_device -> atmel_default_console_device
Signed-off-by: NHaavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This patch removes the static memory mapping for the currently-unused
peripherals [Synchronous Serial, Timer/Counter unit], and for those
drivers that already ioremap() their registers [UART].

Also, the Ethernet driver now uses the platform_device resources but
doesn't yet use ioremap() so we need to pass it the virtual address
instead of the physical address.
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This is more preparation for adding support for the new Atmel AT91SAM9
processors.

Changes include:
- Replace AT91_BASE_* with AT91RM9200_BASE_*
- Replace AT91_ID_* with AT91RM9200_ID_*
- ROM, SRAM and UHP address definitions moved to at91rm9200.h.
- The raw AT91_P[ABCD]_* definitions are now depreciated in favour of
the GPIO API.
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Andrew Victor

This final patch includes some general fixes.

1. Link in pm.o if CONFIG_PM is enabled.  [Should have been included in
patch 3605/1].
2. Use __raw_readl()/__raw_writel() when accessing System Peripheral
registers.
3. Removed some unnecessary includes
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Andrew Victor

This patch maps the AT91RM9200's internal SRAM into the virtual memory
address space - just below the internal peripheral registers.
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch adds support for the Compact Flash controller integrated in
the Atmel AT91RM9200 processor.

Signed-off-by: Andrew Victor <andrew@sanpeople.com
Signed-off-by: NDominik Brodowski <linux@dominikbrodowski.net>

Patch from SAN People

Following changes were made to clock.c:

1) Replaced <asm/hardware/clock.h> with <linux/clk.h>
2) Removed old unused clk_enable & clk_disable.
3) Replaced clk_use/clk_unuse with clk_enable/clk_disable.

Otherwise it's the same as the previous patch.
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>