gfar_halt() was factored out into halting and disabling by commit
d87eb127, as the suspend() method
only wants to do the former.  However, the call to gfar_halt_nodisable()
from gfar_halt() apparently got lost during the patch respin process.

This adds it back.
Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

The drivers below do not use LINUX_VERSION_CODE nor KERNEL_VERSION.
  drivers/net/acenic.c
  drivers/net/bnx2x_link.c
  drivers/net/bnx2x_main.c
  drivers/net/cpmac.c
  drivers/net/gianfar_sysfs.c
  drivers/net/ipg.h
  drivers/net/ppp_mppe.c
  drivers/net/pppol2tp.c
  drivers/net/r6040.c
  drivers/net/sh_eth.c
  drivers/net/sky2.c
  drivers/net/tehuti.h
  drivers/net/typhoon.c

This patch removes the said #include <linux/version.h>.
Signed-off-by: NHuang Weiyi <hwy@cn.fujitsu.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Version update
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Checkpatch compliance
The latest version of checkpatch found the following style errors in the
code
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Spelling mistakes
Spelling has to L's in it...
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Minor code improvements
Small changes to make the code a little bit more efficient and mostly
more readable:
- Using unified macros for EMAC_RD/WR which looks like normal REG_RD/WR
- Removing the NIG_WR since it did nothing and was only confusing
- On bnx2x_panic_dump, print only the used parts of the rings
- define parameters only on the branch they are needed and not at the
  beginning of the function
- using NETIF_MSG_INTR and not private BNX2X_MSG_SP for debug prints
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Driver info
The internal FW which is downloaded by the driver should not be
displayed - it is only causing confusion and it is redundant since it
can be concluded from the driver version. Display only FW which is
burned on the board nvram
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

1G LED does not turn off
The 1G LED was not switched to off when the link was lost
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

8073 PHY changes
The initial support we had for this PHY needs some serious changing. The
major change is that this PHY should be initialized only when the first
function is loaded and not for each function. The official SPI-ROM of
this PHY was released and it requires some changes in the initialization
code as well
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change GPIO for any port
The set GPIO function should receive the port index to allow changing
the GPIO of another port. This is needed for the common init phase (one
the first driver is loaded for the chip)
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pause settings
- 1G pause was not working due to missing write to the emac block
  (TX_MODE_FLOW_EN)
- The flow control should use the negotiated result (after autoneg) so
  we should save both the requested autoneg and the result
- The HW credits with flow control at 1G speed were not optimized and
  caused low throughput
- It is recommended to turn off flow control if the MTU is bigger than
  5000B due to internal buffers size
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Link order with external PHY
When external PHY exists (second chip with the PHY to translate to
another physical medium) the link with the eternal PHY and the network
should be established before setting the link between the 5771x and the
PHY. This is the right order and it is important when using autoneg -
the link to the network should use the autoneg and the link between the
two chips should be forced to the network result.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

No LRO without Rx checksum
Disabling LRO when Rx checksum is disabled
Signed-off-by: NVladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Wrong structure size
The wrong structure was used in the sizeof to clear (luckily both
structures have the same size in this version...)
Signed-off-by: NYitchak Gertner <gertner@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

WoL capability
All designs reported WoL capability regardless of HW limitations - check
if this device is actually capable of WoL
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Clearing MAC addresses filters
When the driver unloads, it should clear the MAC addresses filters in
the HW - this prevents packets from entering the chip when the driver is
re-loaded before initializing the right filters
Signed-off-by: NYitchak Gertner <gertner@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Delay in while loops
The delay in the loop should be after the change. This has very little
effect (can save one delay) but it is the right thing to do
Signed-off-by: NYitchak Gertner <gertner@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

PBA Table Page Alignment Workaround
The PBA table starts on the middle of the page and that's causing very
low performance with virtualization. The solution is not to update via
the BAR directly but via chip access to the same memory
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Self-test false positive
- The memory test should use a mask according to the chip type
- In the register test, check the port only once and not inside the for
  loop (not causing a failure - just ugly)
Signed-off-by: NYitchak Gertner <gertner@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Memory allocation
- The CQE ring was allocated to the max size even for a chip that does
  not support it. Fixed to allocate according to the chip type to save
  memory
- The rx_page_ring was not freed on driver unload
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

HW attention lock
Making sure that only one function will handle the HW attention. This
makes the device parameter aeu_mask redundant so it is removed
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

HW lock mechanism
Enhancing the HW lock to work per function and not only per port - this
is needed for the next patch that protects races over HW attention
detection between the different functions. At this chance, changing the
functions names to be more inline with the current naming convention
Signed-off-by: NYitchak Gertner <gertner@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Load/Unload under traffic
Few issues were found when loading and unloading under traffic:
- When receiving Tx interrupt call netif_wake_queue if the queue is
  stopped but the state is open
- Check that interrupts are enabled before doing anything else on the
  msix_fp_int function
- In nic_load, enable the interrupts only when needed and ready for it
- Function stop_leading returns status since it can fail
- Add 1ms delay when unloading the driver to validate that there are no
  open transactions that already started by the FW
- Splitting the "has work" function into Tx and Rx so the same function
  will be used on unload and interrupts
- Do not request for WoL if only resetting the device (save the time
  that it takes the FW to set the link after reset)
- Fixing the device reset after iSCSI boot and before driver load - all
  internal buffers must be cleared before the driver is loaded
Signed-off-by: NVladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

FW Internal Memory structure
The FW uses data structures on the chip internal memory to aggregate the
connections when TPA is enabled. The driver was clearing the wrong offsets
and therefore one function could cause another function to loose packets.
Changing the initialization of the chip internal memory to clear only the
relevant memory for each function which is being loaded
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Statistics
- Making sure that each drop is accounted for in the driver statistics
- Clearing the FW statistics when driver is loaded to prevent
  inconsistency with HW statistics
- Once error is detected (bnx2x_panic_dump), stop the statistics
  before other actions (currently it is stopped last and can corrupt
  the data) - Adding HW checksum error counter to the statistics
- Removing unused variable stats_ticks
- Using macros instead of magic numbers to indicate which statistics are
  shared per port and which are per function
Signed-off-by: NYitchak Gertner <gertner@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Not dropping packets with L3/L4 checksum error
Those packets should be passed to the OS. The problem is clear in
forwarding mode.
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

FW (bootcode) interface fixes
- Making sure that the device will not cause kernel panic of the
  bootcode is corrupted or missing
- Removing module debug parameter "nomcp" since no one should work
  without the bootcode (this is a left over from the chip bring up days)
- Instead of waiting fix amount of time for bootcode response, sample it
  every 10ms (usually the answer is ready after less than 10ms)
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix dubious logical operation that was found by sparse:
linux-next-20080807/drivers/net/bnx2x_main.c:7205:27: warning: dubious: !x & y
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use a single enum for managing modes, store supported modes by
the HW in a bitmask.
Register legacy rates with mac80211 only at init.
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use ath9k_tx_queue_info which contains the same elements,
and merge get/set functions of tx queue properties.
Also, fix whitespace damage in struct ath_softc.
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch works around an internal compiler error (gcc bug #37014) in
all gcc 4.2 compilers and the gcc 4.3 series up to at least 4.3.1
on at least powerpc and mips.

Many thanks to Andrew Pinski for analyzing the gcc bug.
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This adds the new mac80211 11n ath9k Atheros driver. Only STA support
is currently enabled and tested.
Signed-off-by: NSenthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJack Howarth <howarth@bromo.msbb.uc.edu>
Signed-off-by: NJouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NPavel Roskin <proski@gnu.org>
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Remove Atheros 11n devices from being claimed by ath5k as its
now handled by ath9k.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

these "magic" values must to be the other way round...
Signed-off-by: NChristian Lamparter <chunkeey@web.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It was possible for unsupported operating modes
to be accepted by the add_interface callback function.
This patch will block those modes until proper support
has been implemented for them.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Following "mac80211: fix TX sequence numbers", if a packet
has the IEEE80211_TX_CTL_ASSIGN_SEQ assigned, a sequence number must be
supplied, either by hardware or software. AFAIK, no such hardware exists
for the p54, thus it must be done in software. With this patch, a connection
qith p54usb is stable, whereas the interface went off-line in 2-3 hours
without this change. Note that this code will have to be reworked for proper
sequence numbers on beacons. In addition, the sequence number has been placed
in the hardware state, not the vif state.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>