SCM is the protocol used to communicate between the secure and
non-secure code executing on the applications processor. The
non-secure side uses a physically contiguous buffer to pass
information to the secure side; where the buffer conforms to a
format that is agreed upon by both sides. The use of a buffer
allows multiple pending requests to be in flight on the secure
side. It also benefits use cases where the command or response
buffer contains large chunks of data.
Reviewed-by: NSaravana Kannan <skannan@codeaurora.org>
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NDavid Brown <davidb@codeaurora.org>

There have likewise been some API updates, so we refactor to use the
consolidated smp_prepare_cpus().
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This fixes up the SMP support to use the refactored GIC APIs.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Use the new linux/clkdev.h to get it building again.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Remove now unused IRQ demux code. All R-Mobile and
SH-Mobile processors should register IRQ demux
handlers during run-time.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Break-out GIC specific IRQ demux code from the file
entry-macro-intc.S and register during run-time.

Covers sh73a0.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Break-out INTC specific IRQ demux code from the file
entry-macro-intc.S and register during run-time.

Covers sh7367, sh7377 and sh7372.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Always enable MULTI_IRQ_HANDLER on SH-Mobile.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Use the GIC demux code in asm/hardware/entry-macro-gic.S
on the R-Mobile / SH-Mobile processors.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

When CONFIG_ZBOOT_ROM is selected, the resulting zImage file will be small
boot loader and may be burned to rom or flash.

Cc: Magnus Damm <magnus.damm@gmail.com>
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NSimon Horman <horms@verge.net.au>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Add ARM support for the DMA debug infrastructure, which allows the
DMA API usage to be debugged.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

fsib_clk will be used when fdiv_clk failed on fsi_hdmi_set_rate.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Add a sched_clock() implementation to Versatile Express using the new
sched_clock() infrastructure for extending 32bit counters to full
64-bit nanoseconds.
Tested-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Prepare the ap4evb board for the MIPI DSI driver transition to support

different register layouts.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Now, that the MIPI DSI driver implements runtime PM, we don't need anymore to
configure clocks statically in the platform code. This patch also adds a DSITX1
clock definition for sh7372 and attaches PHY clocks to respective devices.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

sh73a0 has divisor[12] setting as 1/7 on FRQCRA.
Signed-off-by: NTakashi YOSHII <takashi.yoshii.zj@renesas.com>
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Add VGA camera support to the Mackerel board
using soc_camera_platform.

The VGA camera module is hooked up using the
8-bit CEU bus, and it is constantly bursting
out frames in fixed video mode setting. The
camera module does not allow any I2C control.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

1. Add entries to Kconfig
2. Add machine definition
3. Add Uart platform data, pad setting and base address
4. Adjust GPIO irq number
Signed-off-by: NYong Shen <yong.shen@linaro.org>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

1. pll_base address should return right value
2. uart parent clk is from pll3
Signed-off-by: NYong Shen <yong.shen@linaro.org>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Replace some magic numbers with constants and add interrupt definitions.
Signed-off-by: NJochen Friedrich <jochen@scram.de>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Since commit 7a5b4e16, simpad devices don't
boot anymore, since platform devices are registered too early. Fix by moving
the registration from map_io to arch_initcall as done on other sa1100 boards.
Signed-off-by: NJochen Friedrich <jochen@scram.de>
Acked-by: NKristoffer Ericson <kristoffer.ericson@gmail.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Before this patch, the following error would sometimes occur after a
resume on pxa3xx:

    /path/to/mm/memory.c:144: bad pmd 8040542e.

The problem was that a temporary page table mapping was being improperly
restored.

The PXA3xx resume code creates a temporary mapping of resume_turn_on_mmu
to avoid a prefetch abort.  The pxa3xx_resume_after_mmu code requires
that the r1 register holding the address of this mapping not be
modified, however, resume_turn_on_mmu does modify it. It is mostly
correct in that r1 receives the base table address, but it may also
get other bits in 13:0.  This results in pxa3xx_resume_after_mmu
restoring the original mapping to the wrong place, corrupting memory
and leaving the temporary mapping in place.
Signed-off-by: NMatt Reimer <mreimer@sdgsystems.com>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

The commit 6ac6b817 (ARM: pxa: encode
IRQ number into .nr_irqs) removed definition of ITE_LAST_IRQ which
caused the following build error:

CC      arch/arm/common/it8152.o
arch/arm/common/it8152.c: In function 'it8152_init_irq':
arch/arm/common/it8152.c:86: error: 'IT8152_LAST_IRQ' undeclared (first use in this function)
arch/arm/common/it8152.c:86: error: (Each undeclared identifier is reported only once
arch/arm/common/it8152.c:86: error: for each function it appears in.)
make[2]: *** [arch/arm/common/it8152.o] Error 1

Defining the IT8152_LAST_IRQ in the arch/arm/include/hardware/it8152.c
fixes the build.
Signed-off-by: NMike Rapoport <mike@compulab.co.il>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

As arch/arm/mach-pxa/eseries.c references w100fb_gpio_{read,write}()
directly.
Signed-off-by: NLennert Buytenhek <buytenh@secretlab.ca>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

MX27_3DS board has a MC13783 PMIC connected to the CSPI2 port.

Add support for the PMIC.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Replace the page_to_dma() and dma_to_page() macros with their PFN
equivalents.  This allows us to map parts of memory which do not have
a struct page allocated to them to bus addresses.  This will be used
internally by dma_alloc_coherent()/dma_alloc_writecombine().

Build tested on Versatile, OMAP1, IOP13xx and KS8695.
Tested-by: NJanusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Current code doesn't really enable the usb clocks so if they're disabled
when booting linux, the kernel/machine will hang as soon as someone is trying
to read a usb register
Signed-off-by: NArnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NArnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

This patch is fixing some issues :

- MXC_OTG_UCTRL_OPM_BIT is for USBCTRL register and not PHYCTRL register.
- the MXC_EHCI_WAKEUP_ENABLED check was only clearing the bits so never allows
  to set them.
Signed-off-by: NArnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

This patch fixes below build error by adding the missing asm/memory.h,
which is needed for arch_is_coherent().

$ make pxa3xx_defconfig; make
  CC      init/do_mounts_rd.o
In file included from include/linux/list_bl.h:5,
                 from include/linux/rculist_bl.h:7,
                 from include/linux/dcache.h:7,
                 from include/linux/fs.h:381,
                 from init/do_mounts_rd.c:3:
include/linux/bit_spinlock.h: In function 'bit_spin_unlock':
include/linux/bit_spinlock.h:61: error: implicit declaration of function 'arch_is_coherent'
make[1]: *** [init/do_mounts_rd.o] Error 1
make: *** [init] Error 2
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NPeter Huewe <peterhuewe@gmx.de>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>