remove macros and cleanup device exposure checking
Reviewed-by: NScott Teel <scott.teel@pmcs.com>
Reviewed-by: NJustin Lindley <justin.lindley@pmcs.com>
Reviewed-by: NKevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NDon Brace <don.brace@pmcs.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Reviewed-by: NScott Teel <scott.teel@pmcs.com>
Reviewed-by: NJustin Lindley <justin.lindley@pmcs.com>
Reviewed-by: NKevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NDon Brace <don.brace@pmcs.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The driver is using two MACROs which seemingly are looking in
the wrong location for the device_flags returned from
CISS_REPORT_PHYS. Both MACROs, NON_DISK_PHYS_DEV and
PHYS_IOACCEL, are using the pointer returned from figure_lunaddrbytes
which is the address of the LUN.lunid element in
the extended CISS_REPORT_PHYS.  But the MACROS are using offsets
beyond the range of the element (offset 17 of an 8 byte element).

These MACROs actually are looking at the correct location but
they fail static checker analysis. It also will not work
if any new elements are added to the extended LUN structure.

Change the code to use the structure elements directly
since this MACRO is only used in one location.
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: NScott Teel <scott.teel@pmcs.com>
Reviewed-by: NJustin Lindley <justin.lindley@pmcs.com>
Reviewed-by: NKevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NDon Brace <don.brace@pmcs.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Set reset type in device_reset_handler to do either
logical unit reset for logical devices, or physical
target reset, for physical devices.
Reviewed-by: NScott Teel <scott.teel@pmcs.com>
Reviewed-by: NJustin Lindley <justin.lindley@pmcs.com>
Reviewed-by: NKevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NDon Brace <don.brace@pmcs.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Fix a NULL pointer issue in the driver when devices are removed
during a reset.
Signed-off-by: NDon Brace <don.brace@pmcs.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

handle block counts of 0. Cleanup block and block count calculations.
Reviewed-by: NScott Teel <scott.teel@pmcs.com>
Reviewed-by: NJustin Lindley <justin.lindley@pmcs.com>
Reviewed-by: NKevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NDon Brace <don.brace@pmcs.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Abandon and reschedule rescan process only if device inquiries
fail due to mem alloc failures, which are likely to occur for
all devices.

Otherwise, skip device if inquiry fails for other reasons,
and continue rescanning process for other devices.
Reviewed-by: NScott Teel <scott.teel@pmcs.com>
Reviewed-by: NJustin Lindley <justin.lindley@pmcs.com>
Reviewed-by: NKevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NDon Brace <don.brace@pmcs.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Reviewed-by: NScott Teel <scott.teel@pmcs.com>
Reviewed-by: NJustin Lindley <justin.lindley@pmcs.com>
Reviewed-by: NKevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Reviewed-by; Hannes Reinecke <hare@suse.de>
Signed-off-by: NDon Brace <don.brace@pmcs.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Reviewed-by: NManoj Kumar <manoj@linux.vnet.ibm.com>
Signed-off-by: NDon Brace <don.brace@pmcs.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Check for NULLs.
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Reviewed-by: NManoj Kumar <manoj@linux.vnet.ibm.com>
Signed-off-by: NDon Brace <don.brace@pmcs.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This member is used in calls to scsi_device_type.
It should be unsigned since the kernel checks for upper bounds
and it should never be negative.
Suggested-by: NTomas Henzl <thenzl@redhat.com>
Suggested-by: NHannes Reinecke <hare@suse.de>
Suggested-by: NMatthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: NDon Brace <don.brace@pmcs.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This function is no longer used.
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NDon Brace <don.brace@pmcs.com>
Reviewed-by: NManoj Kumar <manoj@linux.vnet.ibm.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

pulling the rug out from under the reset handler
likewise for ioaccel_cmds_out
Reviewed-by: NHannes Reinecke <hare@suse.de>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NDon Brace <don.brace@pmcs.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This parameter was once used before scan_start was defined
but now it is no longer used.
Signed-off-by: NDon Brace <don.brace@pmcs.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Writing a number to /sys/bus/scsi/devices/<sdev>/queue_ramp_up_period
returns the value of that number instead of the number of bytes written.
This behavior can confuse programs expecting POSIX write() semantics.
Fix this by returning the number of bytes written instead.
Signed-off-by: NPeter Oberparleiter <oberpar@linux.vnet.ibm.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Cc: stable@vger.kernel.org
Reviewed-by: NMatthew R. Ochs <mrochs@linux.vnet.ibm.com>
Reviewed-by: NEwan D. Milne <emilne@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Export the RAW SCSI Inquiry to sysfs as binfile. This way the data can be used
by userland without the need to have and ioctl or use the sg_inq tool.

Here is an example of the provided data

linux:~ # hexdump /sys/class/scsi_device/1\:0\:0\:0/device/inquiry
0000000 8005 3205 001f 0000 4551 554d 2020 2020
0000010 4551 554d 4420 4456 522d 4d4f 2020 2020
0000020 2e32 2e33
0000024
Signed-off-by: NJohannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Signed-off-by: NSumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The DELL PERC5 controller firmware does not list tape drives in response
to MR_DCMD_PD_LIST_QUERY. This causes tape drives not be exposed to the
OS when connected to a PERC5 controller.

This patch permits detection of tape drives connected to a PERC5
controller by exposing non-TYPE_DISK devices unconditionally.
Signed-off-by: NKashyap Desai <kashyap.desai@avagotech.com>
Signed-off-by: NSumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

In sg_common_write(), we free the block request and return -ENODEV if
the device is detached in the middle of the SG_IO ioctl().

Unfortunately, sg_finish_rem_req() also tries to free srp->rq, so we
end up freeing rq->cmd in the already free rq object, and then free
the object itself out from under the current user.

This ends up corrupting random memory via the list_head on the rq
object. The most common crash trace I saw is this:

  ------------[ cut here ]------------
  kernel BUG at block/blk-core.c:1420!
  Call Trace:
  [<ffffffff81281eab>] blk_put_request+0x5b/0x80
  [<ffffffffa0069e5b>] sg_finish_rem_req+0x6b/0x120 [sg]
  [<ffffffffa006bcb9>] sg_common_write.isra.14+0x459/0x5a0 [sg]
  [<ffffffff8125b328>] ? selinux_file_alloc_security+0x48/0x70
  [<ffffffffa006bf95>] sg_new_write.isra.17+0x195/0x2d0 [sg]
  [<ffffffffa006cef4>] sg_ioctl+0x644/0xdb0 [sg]
  [<ffffffff81170f80>] do_vfs_ioctl+0x90/0x520
  [<ffffffff81258967>] ? file_has_perm+0x97/0xb0
  [<ffffffff811714a1>] SyS_ioctl+0x91/0xb0
  [<ffffffff81602afb>] tracesys+0xdd/0xe2
    RIP [<ffffffff81281e04>] __blk_put_request+0x154/0x1a0

The solution is straightforward: just set srp->rq to NULL in the
failure branch so that sg_finish_rem_req() doesn't attempt to re-free
it.

Additionally, since sg_rq_end_io() will never be called on the object
when this happens, we need to free memory backing ->cmd if it isn't
embedded in the object itself.

KASAN was extremely helpful in finding the root cause of this bug.
Signed-off-by: NCalvin Owens <calvinowens@fb.com>
Acked-by: NDouglas Gilbert <dgilbert@interlog.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

If MSI(X) interrupts are disabled via the kernel command line
(pci=nomsi), the pm8001 driver will kernel panic because it does not
detect that MSI interrupts are disabled and will soldier on and attempt to
configure MSI interrupts anyways.  This leads to a kernel panic, most
likely because a required data structure is not available down the
line.  Using the pci_msi_enabled() function in order to detect if MSI
interrupts are enabled before configuring them resolves this issue and
avoids a kernel panic when the module is loaded.  Additionally, the
irq_vector structure must be initialized when legacy interrupts are
being used otherwise legacy interrupts will simply not function and
result in another panic.
Signed-off-by: NBenjamin Rood <brood@attotech.com>
Reviewed-by: NJack Wang <jinpu.wang@profitbricks.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The documentation for the 8070 and 8072 SPCv chip explicitly states that
a minimum of 500ms must elapse before issuing commands, otherwise the
SPCv may not process them and the firmware may get into an unrecoverable
state requiring a reboot.  While the Linux guys will probably think this
is 'racy', it is called out in the chip documentation and inserting this
delay makes power management function properly.
Signed-off-by: NBenjamin Rood <brood@attotech.com>
Reviewed-by: NJack Wang <jinpu.wang@profitbricks.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

ATTO adapters do not support this feature.  If the firmware fails to be
ready, it should not check the examined registers in order to examine
the state of the feature in order to prevent undefined behavior.
Signed-off-by: NBenjamin Rood <brood@attotech.com>
Reviewed-by: NJack Wang <jinpu.wang@profitbricks.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

PHY profiles are not saved in NVRAM on ATTO 12Gb SAS controllers.
Therefore, in order for the controller to function in a wide range of
configurations, the PHY profiles must be statically set.  This patch
provides the necessary functionality to do so.
Signed-off-by: NBenjamin Rood <brood@attotech.com>
Reviewed-by: NJack Wang <jinpu.wang@profitbricks.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

ATTO SAS controllers retrieve the SAS address from the NVRAM in a location
different from non-ATTO PMC Sierra SAS controllers.  This patch makes the
necessary adjustments in order to retrieve the SAS address on these types
of adapters.
Signed-off-by: NBenjamin Rood <brood@attotech.com>
Reviewed-by: NJack Wang <jinpu.wang@profitbricks.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

These PCI IDs allow the pm8001 driver to load against ATTO 12Gb SAS
controllers that use PMC Sierra 8070 and PMC Sierra 8072 SAS chips.
Signed-off-by: NBenjamin Rood <brood@attotech.com>
Reviewed-by: NJack Wang <jinpu.wang@profitbricks.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

These SAS controllers support speeds up to 12Gb.
Signed-off-by: NBenjamin Rood <brood@attotech.com>
Reviewed-by: NJack Wang <jinpu.wang@profitbricks.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Previuosly, all PMC Sierra 80xx controllers are assumed to be a
motherboard controller, except if the subsystem vendor ID was equal to
PCI_VENDOR_ID_ADAPTEC.  The driver then attempts to load PHY settings
from NVRAM.  While this may be correct behavior for most controllers, it
does not work with Adaptec and ATTO controllers since they do not store
PHY settings in NVRAM and choose to use either custom PHY settings or
chip defaults.  Loading random values from NVRAM may cause the
controllers to malfunction in this edge case.
Signed-off-by: NBenjamin Rood <brood@attotech.com>
Reviewed-by: NJack Wang <jinpu.wang@profitbricks.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This patch fixes an issue seen with an IBM 2145 (SVC) where, following an error
injection test which results in paths going offline, when they came
back online, the path would timeout the REPORT_LUNS issued during the
scan. This timeout situation continued until retries were expired, resulting in
falling back to a sequential LUN scan. Then, since the target responds
with PQ=1, PDT=0 for all possible LUNs, due to the way the sequential
LUN scan code works, we end up adding 512 LUNs for each target, when there
is really only a small handful of LUNs that are actually present.

This patch increases the timeout used on the REPORT_LUNS to 30 seconds.
This patch solves the issue of 512 non existent LUNs showing up after
this event.
Signed-off-by: NBrian King <brking@linux.vnet.ibm.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Signed-off-by: NSumit Saxena <sumit.saxena@avagotech.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Signed-off-by: NSumit Saxena <sumit.saxena@avagotech.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This is an issue on SMAP enabled CPUs and 32 bit apps running on 64 bit
OS. Do not access user memory from kernel code. The SMAP bit restricts
accessing user memory from kernel code.

Cc: <stable@vger.kernel.org>
Signed-off-by: NSumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: NKashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Signed-off-by: NSumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: NKashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

It may happen (kdump), that an interrupt is invoked just after the
setup_irqs function was called but before the tasklet was initialised.
At this phase the hw ints should have been disabled, but for unknown
reason this mechanism seems to not work properly.

From: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NSumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Signed-off-by: NSumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: NKashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Signed-off-by: NSumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: NKashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Do not use PAGE_SIZE marco to calculate max_sectors per I/O
request. Driver code assumes PAGE_SIZE will be always 4096 which can
lead to wrongly calculated value if PAGE_SIZE is not 4096. This issue
was reported in Ubuntu Bugzilla Bug #1475166.

Cc: <stable@vger.kernel.org>
Signed-off-by: NSumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: NKashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Signed-off-by: NSumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: NKashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Signed-off-by: NSumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: NKashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Remove PCI id based checks and use instance->ctrl_context to decide
whether controller is MFI-based or a Fusion adapter. Additionally,
Fusion adapters are divided into two categories: Thunderbolt and
Invader.
Signed-off-by: NSumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: NKashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Expose non-disk (TAPE drive, CD-ROM) unconditionally.

Cc: <stable@vger.kernel.org>
Signed-off-by: NSumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: NKashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>