Starting from linux-3.13, GRO attempts to build full size skbs.

Problem is the commit assumed one particular field in skb->cb[]
was clean, but it is not the case on some stacked devices.

Timo reported a crash in case traffic is decrypted before
reaching a GRE device.

Fix this by initializing NAPI_GRO_CB(skb)->last at the right place,
this also removes one conditional.

Thanks a lot to Timo for providing full reports and bisecting this.

Fixes: 8a29111c ("net: gro: allow to build full sized skb")
Bisected-by: NTimo Teras <timo.teras@iki.fi>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Tested-by: NTimo Teräs <timo.teras@iki.fi>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The connected check fails to check for ip_gre nbma mode tunnels
properly. ip_gre creates temporary tnl_params with daddr specified
to pass-in the actual target on per-packet basis from neighbor
layer. Detect these tunnels by inspecting the actual tunnel
configuration.

Minimal test case:
 ip route add 192.168.1.1/32 via 10.0.0.1
 ip route add 192.168.1.2/32 via 10.0.0.2
 ip tunnel add nbma0 mode gre key 1 tos c0
 ip addr add 172.17.0.0/16 dev nbma0
 ip link set nbma0 up
 ip neigh add 172.17.0.1 lladdr 192.168.1.1 dev nbma0
 ip neigh add 172.17.0.2 lladdr 192.168.1.2 dev nbma0
 ping 172.17.0.1
 ping 172.17.0.2

The second ping should be going to 192.168.1.2 and head 10.0.0.2;
but cached gre tunnel level route is used and it's actually going
to 192.168.1.1 via 10.0.0.1.

The lladdr's need to go to separate dst for the bug to trigger.
Test case uses separate route entries, but this can also happen
when the route entry is same: if there is a nexthop exception or
the GRE tunnel is IPsec'ed in which case the dst points to xfrm
bundle unique to the gre lladdr.

Fixes: 7d442fab ("ipv4: Cache dst in tunnels")
Signed-off-by: NTimo Teräs <timo.teras@iki.fi>
Cc: Tom Herbert <therbert@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adding more than one chip on device-tree currently causes the probing
routine to always use the first chips data pointer.
Signed-off-by: NFabian Godehardt <fg@emlix.com>
Acked-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, "ip -6 route get mark xyz" ignores the mark passed in
by userspace. Make it honour the mark, just like IPv4 does.
Signed-off-by: NLorenzo Colitti <lorenzo@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There may be padding on the ticket contained in the key payload, so just ensure
that the claimed token length is large enough, rather than exactly the right
size.
Signed-off-by: NNathaniel Wesley Filardo <nwf@cs.jhu.edu>
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

RFC 4861 states in 7.2.5:

	The IsRouter flag in the cache entry MUST be set based on the
         Router flag in the received advertisement.  In those cases
         where the IsRouter flag changes from TRUE to FALSE as a result
         of this update, the node MUST remove that router from the
         Default Router List and update the Destination Cache entries
         for all destinations using that neighbor as a router as
         specified in Section 7.3.3.  This is needed to detect when a
         node that is used as a router stops forwarding packets due to
         being configured as a host.

Currently, when dealing with NA Message which IsRouter flag changes from
TRUE to FALSE, the kernel only removes router from the Default Router List,
and don't update the Destination Cache entries.

Now in order to update those Destination Cache entries, i introduce
function rt6_clean_tohost().
Signed-off-by: NDuan Jiong <duanj.fnst@cn.fujitsu.com>
Acked-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

From: Cong Wang <cwang@twopensource.com>

commit 50624c93 (net: Delay default_device_exit_batch until no
devices are unregistering) introduced rtnl_lock_unregistering() for
default_device_exit_batch(). Same race could happen we when rmmod a driver
which calls rtnl_link_unregister() as we call dev->destructor without rtnl
lock.

For long term, I think we should clean up the mess of netdev_run_todo()
and net namespce exit code.

Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: NCong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: NCong Wang <cwang@twopensource.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change introduced by 88e48d7b
("batman-adv: make DAT drop ARP requests targeting local clients")
implements a check that prevents DAT from using the caching
mechanism when the client that is supposed to provide a reply
to an arp request is local.

However change brought by be1db4f6
("batman-adv: make the Distributed ARP Table vlan aware")
has not converted the above check into its vlan aware version
thus making it useless when the local client is behind a vlan.

Fix the behaviour by properly specifying the vlan when
checking for a client being local or not.
Reported-by: NSimon Wunderlich <simon@open-mesh.com>
Signed-off-by: NAntonio Quartulli <antonio@open-mesh.com>
Signed-off-by: NMarek Lindner <mareklindner@neomailbox.ch>

A pointer to the orig_node representing a bat-gateway is
stored in the gw_node->orig_node member, but the refcount
for such orig_node is never increased.
This leads to memory faults when gw_node->orig_node is accessed
and the originator has already been freed.

Fix this by increasing the refcount on gw_node creation
and decreasing it on gw_node free.
Signed-off-by: NAntonio Quartulli <antonio@open-mesh.com>
Signed-off-by: NMarek Lindner <mareklindner@neomailbox.ch>

In the new fragmentation code the batadv_frag_send_packet()
function obtains a reference to the primary_if, but it does
not release it upon return.

This reference imbalance prevents the primary_if (and then
the related netdevice) to be properly released on shut down.

Fix this by releasing the primary_if in batadv_frag_send_packet().

Introduced by ee75ed88
("batman-adv: Fragment and send skbs larger than mtu")

Cc: Martin Hundebøll <martin@hundeboll.net>
Signed-off-by: NAntonio Quartulli <antonio@open-mesh.com>
Signed-off-by: NMarek Lindner <mareklindner@neomailbox.ch>
Acked-by: NMartin Hundebøll <martin@hundeboll.net>

If hard_iface is NULL and goto out is made batadv_hardif_free_ref()
doesn't check for NULL before dereferencing it to get to refcount.

Introduced in cb1c92ec
("batman-adv: add debugfs support to view multiif tables").
Reported-by: NSven Eckelmann <sven@narfation.org>
Signed-off-by: NMarek Lindner <mareklindner@neomailbox.ch>
Acked-by: NAntonio Quartulli <antonio@meshcoding.com>
Signed-off-by: NAntonio Quartulli <antonio@meshcoding.com>

When sending data through IUCV a MESSAGE COMPLETE interrupt
signals that sent data memory can be freed or reused again.
With commit f9c41a62
"af_iucv: fix recvmsg by replacing skb_pull() function" the
MESSAGE COMPLETE callback iucv_callback_txdone() identifies
the wrong skb as being confirmed, which leads to data corruption.
This patch fixes the skb mapping logic in iucv_callback_txdone().
Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com>
Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jouni reported that if a remain-on-channel was active on the
same channel as the current operating channel, then the ROC
would start, but any frames transmitted using mgmt-tx on the
same channel would get delayed until after the ROC.

The reason for this is that the ROC starts, but doesn't have
any handling for "remain on the same channel", so it stops
the interface queues. The later mgmt-tx then puts the frame
on the interface queues (since it's on the current operating
channel) and thus they get delayed until after the ROC.

To fix this, add some logic to handle remaining on the same
channel specially and not stop the queues etc. in this case.
This not only fixes the bug but also improves behaviour in
this case as data frames etc. can continue to flow.

Cc: stable@vger.kernel.org
Reported-by: NJouni Malinen <j@w1.fi>
Tested-by: NJouni Malinen <j@w1.fi>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

tot_len does specify the size of struct ipv6_txoptions. We need opt_flen +
opt_nflen to calculate the overall length of additional ipv6 extensions.

I found this while auditing the ipv6 output path for a memory corruption
reported by Alexey Preobrazhensky while he fuzzed an instrumented
AddressSanitizer kernel with trinity. This may or may not be the cause
of the original bug.

Fixes: 4df98e76 ("ipv6: pmtudisc setting not respected with UFO/CORK")
Reported-by: NAlexey Preobrazhensky <preobr@google.com>
Signed-off-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

net_get_random_once depends on the static keys infrastructure to patch up
the branch to the slow path during boot. This was realized by abusing the
static keys api and defining a new initializer to not enable the call
site while still indicating that the branch point should get patched
up. This was needed to have the fast path considered likely by gcc.

The static key initialization during boot up normally walks through all
the registered keys and either patches in ideal nops or enables the jump
site but omitted that step on x86 if ideal nops where already placed at
static_key branch points. Thus net_get_random_once branches not always
became active.

This patch switches net_get_random_once to the ordinary static_key
api and thus places the kernel fast path in the - by gcc considered -
unlikely path.  Microbenchmarks on Intel and AMD x86-64 showed that
the unlikely path actually beats the likely path in terms of cycle cost
and that different nop patterns did not make much difference, thus this
switch should not be noticeable.

Fixes: a48e4292 ("net: introduce new macro net_get_random_once")
Reported-by: NTuomas Räsänen <tuomasjjrasanen@tjjr.fi>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since commit 7e980569("ipv6: router reachability probing"), a router falls
into NUD_FAILED will be probed.

Now if function rt6_select() selects a router which neighbour state is NUD_FAILED,
and at the same time function rt6_probe() changes the neighbour state to NUD_PROBE,
then function dst_neigh_output() can directly send packets, but actually the
neighbour still is unreachable. If we set nud_state to NUD_INCOMPLETE instead
NUD_PROBE, packets will not be sent out until the neihbour is reachable.

In addition, because the route should be probes with a single NS, so we must
set neigh->probes to neigh_max_probes(), then the neigh timer timeout and function
neigh_timer_handler() will not send other NS Messages.
Signed-off-by: NDuan Jiong <duanj.fnst@cn.fujitsu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the association is in progress while we suspend, the
stack will be in a messed up state. Clean it before we
suspend.

This patch completes Johannes's patch:

1a1cb744
Author: Johannes Berg <johannes.berg@intel.com>

    mac80211: fix suspend vs. authentication race

Cc: <stable@vger.kernel.org>
Fixes: 12e7f517 ("mac80211: cleanup generic suspend/resume procedures")
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The function ip6_tnl_validate assumes that the rtnl
attribute IFLA_IPTUN_PROTO always be filled . If this
attribute is not filled by  the userspace application
kernel get crashed with NULL pointer dereference. This
patch fixes the potential kernel crash when
IFLA_IPTUN_PROTO is missing .
Signed-off-by: NSusant Sahani <susant@redhat.com>
Acked-by: NThomas Graf <tgraf@suug.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We need to use the mark we get from the tunnels o_key to
lookup the right vti state in the error handlers. This patch
ensures that.

Fixes: df3893c1 ("vti: Update the ipv4 side to use it's own receive hook.")
Fixes: fa9ad96d ("vti6: Update the ipv6 side to use its own receive hook.")
Signed-off-by: NSteffen Klassert <steffen.klassert@secunet.com>

If we fail to register one of the xfrm protocol handlers we will
unregister the pernet ops twice on the error exit path. This will
probably lead to a kernel panic as the double deregistration
leads to a double kfree().

Fix this by removing one of the calls to do it only once.

Fixes: fa9ad96d ("vti6: Update the ipv6 side to use its own...")
Signed-off-by: NMathias Krause <minipli@googlemail.com>
Signed-off-by: NSteffen Klassert <steffen.klassert@secunet.com>

When an interface is removed separately, all neighbors need to be
checked if they have a neigh_ifinfo structure for that particular
interface. If that is the case, remove that ifinfo so any references to
a hard interface can be freed.

This is a regression introduced by
89652331
("batman-adv: split tq information in neigh_node struct")
Reported-by: NAntonio Quartulli <antonio@open-mesh.com>
Signed-off-by: NSimon Wunderlich <simon@open-mesh.com>
Signed-off-by: NMarek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: NAntonio Quartulli <antonio@meshcoding.com>

The current code will not execute batadv_purge_orig_neighbors() when an
orig_ifinfo has already been purged. However we need to run it in any
case. Fix that.

This is a regression introduced by
7351a482
("batman-adv: split out router from orig_node")
Signed-off-by: NSimon Wunderlich <simon@open-mesh.com>
Signed-off-by: NMarek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: NAntonio Quartulli <antonio@meshcoding.com>

When an interface is removed from batman-adv, the orig_ifinfo of a
orig_node may be removed without releasing the router first.
This will prevent the reference for the neighbor pointed at by the
orig_ifinfo->router to be released, and this leak may result in
reference leaks for the interface used by this neighbor. Fix that.

This is a regression introduced by
7351a482
("batman-adv: split out router from orig_node").
Reported-by: NAntonio Quartulli <antonio@open-mesh.com>
Signed-off-by: NSimon Wunderlich <simon@open-mesh.com>
Signed-off-by: NMarek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: NAntonio Quartulli <antonio@meshcoding.com>

The neigh_ifinfo object must be freed if it has been used in
batadv_iv_ogm_process_per_outif().

This is a regression introduced by
89652331
("batman-adv: split tq information in neigh_node struct")
Reported-by: NAntonio Quartulli <antonio@open-mesh.com>
Signed-off-by: NSimon Wunderlich <simon@open-mesh.com>
Signed-off-by: NMarek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: NAntonio Quartulli <antonio@meshcoding.com>

If sdata doesn't have a valid dev (e.g. in case of monitor
vif), the vif_name field was initialized with (a length of)
some short string, but later was set to a different,
potentially larger one.

This resulted in out-of-bounds write, which usually
appeared as garbage in the trace log.

Simply trace sdata->name, as it should always have the
correct name for both cases.
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

There are two (related) issues with this.

One case, reported by Michal, is related to hostap: it unsets the
20/40 capability bit for stations that associate when it's in 20
MHz mode.

The other case, reported by Eyal, is that some APs like Netgear
R6300v2 and probably others based on the BCM4360 chipset can be
configured for doing VHT at 20Mhz. In this case the beacon has
a VHT IE but the HT cap indicates transmitter only support 20Mhz.

In both of these cases, we currently avoid VHT and use only HT
this means we can't use the highest rates (MCS8), so fixing this
leads to throughput improvements.
Reported-by: NMichal Kazior <michal.kazior@tieto.com>
Reported-by: NEyal Shapira <eyal@wizery.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Similarly, when CONFIG_SYSCTL is not set, ping_group_range should still
work, just that no one can change it. Therefore we should move it out of
sysctl_net_ipv4.c. And, it should not share the same seqlock with
ip_local_port_range.

BTW, rename it to ->ping_group_range instead.

Cc: David S. Miller <davem@davemloft.net>
Cc: Francois Romieu <romieu@fr.zoreil.com>
Reported-by: NStefan de Konink <stefan@konink.de>
Signed-off-by: NCong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When CONFIG_SYSCTL is not set, ip_local_port_range should still work,
just that no one can change it. Therefore we should move it out of sysctl_inet.c.
Also, rename it to ->ip_local_ports instead.

Cc: David S. Miller <davem@davemloft.net>
Cc: Francois Romieu <romieu@fr.zoreil.com>
Reported-by: NStefan de Konink <stefan@konink.de>
Signed-off-by: NCong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Dst is released one line before we access it again with dst->error.

Fixes: 58e35d14 netfilter: ipv6: propagate routing errors from
ip6_route_me_harder()
Signed-off-by: NSergey Popovich <popovich_sergei@mail.ru>
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>

Increment fib_info_cnt in fib_create_info() right after successfuly
alllocating fib_info structure, overwise fib_metrics allocation failure
leads to fib_info_cnt incorrectly decremented in free_fib_info(), called
on error path from fib_create_info().
Signed-off-by: NSergey Popovich <popovich_sergei@mail.ru>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit d2069403,
there are no more callers.
Signed-off-by: NFlorian Westphal <fw@strlen.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Doing the segmentation in the forward path has one major drawback:

When using virtio, we may process gso udp packets coming
from host network stack.  In that case, netfilter POSTROUTING
will see one packet with udp header followed by multiple ip
fragments.

Delay the segmentation and do it after POSTROUTING invocation
to avoid this.

Fixes: fe6cc55f ("net: ip, ipv6: handle gso skbs in forwarding path")
Signed-off-by: NFlorian Westphal <fw@strlen.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If conntrack defragments incoming ipv6 frags it stores largest original
frag size in ip6cb and sets ->local_df.

We must thus first test the largest original frag size vs. mtu, and not
vice versa.

Without this patch PKTTOOBIG is still generated in ip6_fragment() later
in the stack, but

1) IPSTATS_MIB_INTOOBIGERRORS won't increment
2) packet did (needlessly) traverse netfilter postrouting hook.

Fixes: fe6cc55f ("net: ip, ipv6: handle gso skbs in forwarding path")
Signed-off-by: NFlorian Westphal <fw@strlen.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

local_df means 'ignore DF bit if set', so if its set we're
allowed to perform ip fragmentation.

This wasn't noticed earlier because the output path also drops such skbs
(and emits needed icmp error) and because netfilter ip defrag did not
set local_df until couple of days ago.

Only difference is that DF-packets-larger-than MTU now discarded
earlier (f.e. we avoid pointless netfilter postrouting trip).

While at it, drop the repeated test ip_exceeds_mtu, checking it once
is enough...

Fixes: fe6cc55f ("net: ip, ipv6: handle gso skbs in forwarding path")
Signed-off-by: NFlorian Westphal <fw@strlen.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We don't catch the case if an unsupported protocol is submitted
to the xfrm6 protocol handlers, this can lead to NULL pointer
dereferences. Fix this by adding the appropriate checks.

Fixes: 7e14ea15 ("xfrm6: Add IPsec protocol multiplexer")
Signed-off-by: NSteffen Klassert <steffen.klassert@secunet.com>

In ip_tunnel_rcv(), set skb->network_header to inner IP header
before IP_ECN_decapsulate().

Without the fix, IP_ECN_decapsulate() takes outer IP header as
inner IP header, possibly causing error messages or packet drops.

Note that this skb_reset_network_header() call was in this spot when
the original feature for checking consistency of ECN bits through
tunnels was added in eccc1bb8 ("tunnel: drop packet if ECN present
with not-ECT"). It was only removed from this spot in 3d7b46cd
("ip_tunnel: push generic protocol handling to ip_tunnel module.").

Fixes: 3d7b46cd ("ip_tunnel: push generic protocol handling to ip_tunnel module.")
Reported-by: NNeal Cardwell <ncardwell@google.com>
Signed-off-by: NYing Cai <ycai@google.com>
Acked-by: NNeal Cardwell <ncardwell@google.com>
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Right now the core vsock module is the owner of the proto family. This
means there's nothing preventing the transport module from unloading if
there are open sockets, which results in a panic. Fix that by allowing
the transport to be the owner, which will refcount it properly.

Includes version bump to 1.0.1.0-k

Passes checkpatch this time, I swear...
Acked-by: NDmitry Torokhov <dtor@vmware.com>
Signed-off-by: NAndy King <acking@vmware.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently bridge can silently drop ipv4 fragments.
If node have loaded nf_defrag_ipv4 module but have no nf_conntrack_ipv4,
br_nf_pre_routing defragments incoming ipv4 fragments
but nfct check in br_nf_dev_queue_xmit does not allow re-fragment combined
packet back, and therefore it is dropped in br_dev_queue_push_xmit without
incrementing of any failcounters

It seems the only way to hit the ip_fragment code in the bridge xmit
path is to have a fragment list whose reassembled fragments go over
the mtu. This only happens if nf_defrag is enabled. Thanks to
Florian Westphal for providing feedback to clarify this.

Defragmentation ipv4 is required not only in conntracks but at least in
TPROXY target and socket match, therefore #ifdef is changed from
NF_CONNTRACK_IPV4 to NF_DEFRAG_IPV4
Signed-off-by: NVasily Averin <vvs@openvz.org>
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>

Defrag user check in ip_expire was not updated after adding support for
"conntrack zones".

This bug manifests as a RFC violation, since the router will send
the icmp time exceeeded message when using conntrack zones.
Signed-off-by: NVasily Averin <vvs@openvz.org>
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>

ieee80211_reconfig already holds rtnl, so calling
cfg80211_sched_scan_stopped results in deadlock.

Use the rtnl-version of this function instead.

Fixes: d43c6b6e ("mac80211: reschedule sched scan after HW restart")
Cc: stable@vger.kernel.org (3.14+)
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>