The first cpu which switches from periodic to oneshot mode switches
also the broadcast device into oneshot mode. The broadcast device
serves as a backup for per cpu timers which stop in deeper
C-states. To avoid starvation of the cpus which might be in idle and
depend on broadcast mode it marks the other cpus as broadcast active
and sets the brodcast expiry value of those cpus to the next tick.

The oneshot mode broadcast bit for the other cpus is sticky and gets
only cleared when those cpus exit idle. If a cpu was not idle while
the bit got set in consequence the bit prevents that the broadcast
device is armed on behalf of that cpu when it enters idle for the
first time after it switched to oneshot mode.

In most cases that goes unnoticed as one of the other cpus has usually
a timer pending which keeps the broadcast device armed with a short
timeout. Now if the only cpu which has a short timer active has the
bit set then the broadcast device will not be armed on behalf of that
cpu and will fire way after the expected timer expiry. In the case of
Christians bug report it took ~145 seconds which is about half of the
wrap around time of HPET (the limit for that device) due to the fact
that all other cpus had no timers armed which expired before the 145
seconds timeframe.

The solution is simply to clear the broadcast active bit
unconditionally when a cpu switches to oneshot mode after the first
cpu switched the broadcast device over. It's not idle at that point
otherwise it would not be executing that code.

[ I fundamentally hate that broadcast crap. Why the heck thought some
  folks that when going into deep idle it's a brilliant concept to
  switch off the last device which brings the cpu back from that
  state? ]

Thanks to Christian for providing all the valuable debug information!
Reported-and-tested-by: NChristian Hoffmann <email@christianhoffmann.info>
Cc: John Stultz <johnstul@us.ibm.com>
Link: http://lkml.kernel.org/r/%3Calpine.LFD.2.02.1105161105170.3078%40ionos%3E
Cc: stable@kernel.org
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

Avoid taking broadcast_lock in the idle path for systems where the
timer doesn't stop in C3.

[ tglx: Removed the stale label and added comment ]
Signed-off-by: NAndi Kleen <ak@linux.intel.com>
Cc: Dave Kleikamp <dkleikamp@gmail.com>
Cc: Chris Mason <chris.mason@oracle.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Tim Chen <tim.c.chen@linux.intel.com>
Cc: lenb@kernel.org
Cc: paulmck@us.ibm.com
Link: http://lkml.kernel.org/r/%3C20110504234806.GF2925%40one.firstfloor.org%3ESigned-off-by: NThomas Gleixner <tglx@linutronix.de>

When the per cpu timer is marked CLOCK_EVT_FEAT_C3STOP, then we only
can switch into oneshot mode, when the backup broadcast device
supports oneshot mode as well. Otherwise we would try to switch the
broadcast device into an unsupported mode unconditionally. This went
unnoticed so far as the current available broadcast devices support
oneshot mode. Seth unearthed this problem while debugging and working
around an hpet related BIOS wreckage.

Add the necessary check to tick_is_oneshot_available().
Reported-and-tested-by: NSeth Forshee <seth.forshee@canonical.com>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
LKML-Reference: <alpine.LFD.2.00.1102252231200.2701@localhost6.localdomain6>
Cc: stable@kernel.org # .21 ->

All callers of do_timer() are converted to xtime_update(). The only
users of xtime_lock are in kernel/time/. Make both local to
kernel/time/ and remove them from the global header files.

[ tglx: Reuse tick-internal.h instead of creating another local header
  	file. Massaged changelog ]
Signed-off-by: NTorben Hohn <torbenh@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: johnstul@us.ibm.com
Cc: yong.zhang0@gmail.com
Cc: hch@infradead.org
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Convert locks which cannot be sleeping locks in preempt-rt to
raw_spinlocks.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Acked-by: NPeter Zijlstra <peterz@infradead.org>
Acked-by: NIngo Molnar <mingo@elte.hu>

Currently clockevents_notify() is called with interrupts enabled at
some places and interrupts disabled at some other places.

This results in a deadlock in this scenario.

cpu A holds clockevents_lock in clockevents_notify() with irqs enabled
cpu B waits for clockevents_lock in clockevents_notify() with irqs disabled
cpu C doing set_mtrr() which will try to rendezvous of all the cpus.

This will result in C and A come to the rendezvous point and waiting
for B. B is stuck forever waiting for the spinlock and thus not
reaching the rendezvous point.

Fix the clockevents code so that clockevents_lock is taken with
interrupts disabled and thus avoid the above deadlock.

Also call lapic_timer_propagate_broadcast() on the destination cpu so
that we avoid calling smp_call_function() in the clockevents notifier
chain.

This issue left us wondering if we need to change the MTRR rendezvous
logic to use stop machine logic (instead of smp_call_function) or add
a check in spinlock debug code to see if there are other spinlocks
which gets taken under both interrupts enabled/disabled conditions.
Signed-off-by: NSuresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: NVenkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: "Pallipadi Venkatesh" <venkatesh.pallipadi@intel.com>
Cc: "Brown Len" <len.brown@intel.com>
LKML-Reference: <1250544899.2709.210.camel@sbs-t61.sc.intel.com>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

The variable tick_broadcast_device is not used outside of the
file where it is defined, so let's make it static.
Signed-off-by: NDmitri Vorobiev <dmitri.vorobiev@movial.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

Impact: cleanup

Simple replacement, now the _nr is redundant.
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>
Signed-off-by: NMike Travis <travis@sgi.com>
Cc: Ingo Molnar <mingo@redhat.com>

Impact: Use new APIs

Convert kernel/time functions to use struct cpumask *.

Note the ugly bitmap declarations in tick-broadcast.c.  These should
be cpumask_var_t, but there was no obvious initialization function to
put the alloc_cpumask_var() calls in.  This was safe.

(Eventually 'struct cpumask' will be undefined for CONFIG_CPUMASK_OFFSTACK,
so we use a bitmap here to show we really mean it).
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>
Signed-off-by: NMike Travis <travis@sgi.com>

Impact: change calling convention of existing clock_event APIs

struct clock_event_timer's cpumask field gets changed to take pointer,
as does the ->broadcast function.

Another single-patch change.  For safety, we BUG_ON() in
clockevents_register_device() if it's not set.
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>
Cc: Ingo Molnar <mingo@elte.hu>

We did not restart the tick device from irq_enter() to avoid double
reprogramming and extra events in the return immediate to idle case.

But long lasting softirqs can lead to a situation where jiffies become
stale:

idle()
  tick stopped (reprogrammed to next pending timer)
  halt()
   interrupt
     jiffies updated from irq_enter()
     interrupt handler
     softirq function 1 runs 20ms
     softirq function 2 arms a 10ms timer with a stale jiffies value
     jiffies updated from irq_exit()
     timer wheel has now an already expired timer
     (the one added in function 2)
     timer fires and timer softirq runs

This was discovered when debugging a timer problem which happend only
when the ath5k driver is active. The debugging proved that there is a
softirq function running for more than 20ms, which is a bug by itself.

To solve this we restart the tick timer right from irq_enter(), but do
not go through the other functions which are necessary to return from
idle when need_resched() is set.
Reported-by: NElias Oltmanns <eo@nebensachen.de>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Tested-by: NElias Oltmanns <eo@nebensachen.de>

Impact: jiffies increment too fast.

Hugh Dickins noted that with NOHZ=n and HIGHRES=n jiffies get
incremented too fast. The reason is a wrong check in the broadcast
enter/exit code, which keeps the local apic timer in periodic mode
when the switch happens.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

Impact: timer hang on CPU online observed on AMD C1E systems

When a CPU is brought online then the broadcast machinery can
be in the one shot state already. Check this and setup the timer 
device of the new CPU in one shot mode so the broadcast code
can pick up the next_event value correctly.

Another AMD C1E oddity, as we switch to broadcast immediately and
not after the full bring up via the ACPI cpu idle code.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

Impact: Possible hang on CPU online observed on AMD C1E machines.

The broadcast setup code looks at the mode of the tick device to
determine whether it needs to be shut down or setup. This is wrong
when the broadcast mode is set to one shot already. This can happen
when a CPU is brought online as it goes through the periodic setup
first.

The problem went unnoticed as sane systems do not call into that code
before the switch to one shot for the clock event device happens.
The AMD C1E idle routine switches over immediately and thereby shuts
down the just setup device before the first interrupt happens.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

The device shut down does not cleanup the next_event variable of the
clock event device. So when the device is reactivated the possible
stale next_event value can prevent the device to be reprogrammed as it
claims to wait on a event already.

This is the root cause of the resurfacing suspend/resume problem,
where systems need key press to come back to life.

Fix this by setting next_event to KTIME_MAX when the device is shut
down. Use a separate function for shutdown which takes care of that
and only keep the direct set mode call in the broadcast code, where we
can not touch the next_event value.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

Until the C1E patches arrived there where no users of periodic broadcast
before switching to oneshot mode. Now we need to trigger a possible
waiter for a periodic broadcast when switching to oneshot mode.
Otherwise we can starve them for ever.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

The C1E/HPET bug reports on AMDX2/RS690 systems where tracked down to a
too small value of the HPET minumum delta for programming an event.

The clockevents code needs to enforce an interrupt event on the clock event
device in some cases. The enforcement code was stupid and naive, as it just
added the minimum delta to the current time and tried to reprogram the device.
When the minimum delta is too small, then this loops forever.

Add a sanity check. Allow reprogramming to fail 3 times, then print a warning
and double the minimum delta value to make sure, that this does not happen again.
Use the same function for both tick-oneshot and tick-broadcast code.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

While chasing the C1E/HPET bugreports I went through the clock events
code inch by inch and found that the broadcast device can be initialized
and shutdown multiple times. Multiple shutdowns are not critical, but
useless waste of time. Multiple initializations are simply broken. Another
CPU might have the device in use already after the first initialization and
the second init could just render it unusable again.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

The reprogramming of the periodic broadcast handler was broken,
when the first programming returned -ETIME. The clockevents code
stores the new expiry value in the clock events device next_event field
only when the programming time has not been elapsed yet. The loop in
question calculates the new expiry value from the next_event value
and therefor never increases.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

C1E on AMD machines is like C3 but without control from the OS. Up to
now we disabled the local apic timer for those machines as it stops
when the CPU goes into C1E. This excludes those machines from high
resolution timers / dynamic ticks, which hurts especially X2 based
laptops.

The current boot time C1E detection has another, more serious flaw
as well: some BIOSes do not enable C1E until the ACPI processor module
is loaded. This causes systems to stop working after that point.

To work nicely with C1E enabled machines we use a separate idle
function, which checks on idle entry whether C1E was enabled in the
Interrupt Pending Message MSR. This allows us to do timer broadcasting
for C1E and covers the late enablement of C1E as well.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

It's never used and the comments refer to nonatomic and retry
interchangably. So get rid of it.
Acked-by: NJeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

Change references from for_each_cpu_mask to for_each_cpu_mask_nr
where appropriate
Reviewed-by: NPaul Jackson <pj@sgi.com>
Reviewed-by: NChristoph Lameter <clameter@sgi.com>
Signed-off-by: NMike Travis <travis@sgi.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

braodcast -> broadcast
Signed-off-by: NGlauber Costa <gcosta@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

> Generic code is not supposed to include irq.h. Replace this include
> by linux/hardirq.h instead and add/replace an include of linux/irq.h
> in asm header files where necessary.
> This change should only matter for architectures that make use of
> GENERIC_CLOCKEVENTS.
> Architectures in question are mips, x86, arm, sh, powerpc, uml and sparc64.
>
> I did some cross compile tests for mips, x86_64, arm, powerpc and sparc64.
> This patch fixes also build breakages caused by the include replacement in
> tick-common.h.

I generally dislike adding optional linux/* includes in asm/* includes -
I'm nervous about this causing include loops.

However, there's a separate point to be discussed here.

That is, what interfaces are expected of every architecture in the kernel.
If generic code wants to be able to set the affinity of interrupts, then
that needs to become part of the interfaces listed in linux/interrupt.h
rather than linux/irq.h.

So what I suggest is this approach instead (against Linus' tree of a
couple of days ago) - we move irq_set_affinity() and irq_can_set_affinity()
to linux/interrupt.h, change the linux/irq.h includes to linux/interrupt.h
and include asm/irq_regs.h where needed (asm/irq_regs.h is supposed to be
rarely used include since not much touches the stacked parent context
registers.)

Build tested on ARM PXA family kernels and ARM's Realview platform
kernels which both use genirq.

[ tglx@linutronix.de: add GENERIC_HARDIRQ dependencies ]
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>

clean up tick-broadcast.c
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Resolve the following regression of a choppy, almost unusable laptop:

 http://lkml.org/lkml/2007/12/7/299
 http://bugzilla.kernel.org/show_bug.cgi?id=9525

A previous version of the code did the reprogramming of the broadcast
device in the return from idle code. This was removed, but the logic in
tick_handle_oneshot_broadcast() was kept the same.

When a broadcast interrupt happens we signal the expiry to all CPUs
which have an expired event. If none of the CPUs has an expired event,
which can happen in dyntick mode, then we reprogram the broadcast
device. We do not reprogram otherwise, but this is only correct if all
CPUs, which are in the idle broadcast state have been woken up.

The code ignores, that there might be pending not yet expired events on
other CPUs, which are in the idle broadcast state. So the delivery of
those events can be delayed for quite a time.

Change the tick_handle_oneshot_broadcast() function to check for CPUs,
which are in broadcast state and are not woken up by the current event,
and enforce the rearming of the broadcast device for those CPUs.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Signed-off-by: NLi Zefan <lizf@cn.fujitsu.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: john stultz <johnstul@us.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Doh, I completely missed that devices marked DUMMY are not running
the set_mode function. So we force broadcasting, but we keep the
local APIC timer running.

Let the clock event layer mark the device _after_ switching it off.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

smp_call_function_single() now knows how to call the function on the
current cpu.

Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: NAvi Kivity <avi@qumranet.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The 64bit SMP bootup is slightly different to the 32bit one. It enables
the boot CPU local APIC timer before all CPUs are brought up. Some AMD C1E
systems have the C1E feature flag only set in the secondary CPU. Due to
the early enable of the boot CPU local APIC timer the APIC timer is
registered as a fully functional device. When we detect the wreckage during
the bringup of the secondary CPU, we need to force the boot CPU into
broadcast mode. 

Add a new notifier reason and implement the force broadcast in the clock
events layer.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

Change the broadcast timer, if a timer with higher rating becomes available.
Signed-off-by: NVenkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Andi Kleen <ak@suse.de>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NArjan van de Ven <arjan@linux.intel.com>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

The next_event member of the clock event device is used to keep track
of the next periodic event. For one shot only devices it is wrong to
clear the variable, as the next event will be based on it.

Pointed out by Ralf Baechle
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NArjan van de Ven <arjan@linux.intel.com>

In a desparate attempt to fix the suspend/resume problem on Andrews
VAIO I added a workaround which enforced the broadcast of the oneshot
timer on resume. This was actually resolving the problem on the VAIO
but was just a stupid workaround, which was not tackling the root
cause: the assignement of lower idle C-States in the ACPI processor_idle
code. The cpuidle patches, which utilize the dynamic tick feature and
go faster into deeper C-states exposed the problem again. The correct
solution is the previous patch, which prevents lower C-states across
the suspend/resume.

Remove the enforcement code, including the conditional broadcast timer
arming, which helped to pamper over the real problem for quite a time.
The oneshot broadcast flag for the cpu, which runs the resume code can
never be set at the time when this code is executed. It only gets set,
when the CPU is entering a lower idle C-State.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Tested-by: NAndrew Morton <akpm@linux-foundation.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

When a cpu goes offline it is removed from the broadcast masks. If the
mask becomes empty the code shuts down the broadcast device. This is
wrong, because the broadcast device needs to be ready for the online
cpu going idle (into a c-state, which stops the local apic timer).
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

The jinxed VAIO refuses to resume without hitting keys on the keyboard
when this is not enforced. It is unclear why the cpu ends up in a lower
C State without notifying the clock events layer, but enforcing the
oneshot broadcast here is safe.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

When a device is replaced by a better rated device, then the broadcast
mode needs to be evaluated again. When the new device has no requirement
for broadcasting, then the broadcast bits for the CPU must be cleared.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: john stultz <johnstul@us.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

We need to make sure, that the clockevent devices are resumed, before
the tick is resumed. The current resume logic does not guarantee this.

Add CLOCK_EVT_MODE_RESUME and call the set mode functions of the clock
event devices before resuming the tick / oneshot functionality.

Fixup the existing users.

Thanks to Nigel Cunningham for tracking down a long standing thinko,
which affected the jinxed VAIO.

[akpm@linux-foundation.org: xen build fix]
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Booting a SMP kernel with maxcpus=1 on a SMP system leads to a hard hang,
because ACPI ignores the maxcpus setting and sends timer broadcast info for
the offline CPUs.  This results in a stuck for ever call to
smp_call_function_single() on an offline CPU.

Ignore the bogus information and print a kernel error to remind ACPI
folks to fix it.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

I finally found a dual core box, which survives suspend/resume without
crashing in the middle of nowhere. Sigh, I never figured out from the
code and the bug reports what's going on.

The observed hangs are caused by a stale state transition of the clock
event devices, which keeps the RCU synchronization away from completion,
when the non boot CPU is brought back up.

The suspend/resume in oneshot mode needs the similar care as the
periodic mode during suspend to RAM. My assumption that the state
transitions during the different shutdown/bringups of s2disk would go
through the periodic boot phase and then switch over to highres resp.
nohz mode were simply wrong.

Add the appropriate suspend / resume handling for the non periodic
modes.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>