1) Update copyright
2) Fix hardware queue descriptor field size CQ_ENET_RQ_DESC_FCOE_SOF_BITS
3) Include rtnetlink.h instead of if_link.h
4) Selectively flush writes to interrupt mask register
5) Use pci_enable_device_mem
6) Remove unused variables and header files
7) Fix size mismatch between memory alloc and free operations of a variable
8) Check for non null arguments to vic_provinfo_alloc
Signed-off-by: NScott Feldman <scofeldm@cisco.com>
Signed-off-by: NVasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: NRoopa Prabhu <roprabhu@cisco.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Handle surprise hardware removals gracefully during devcmd issue and init,
cleanup of queues.
Signed-off-by: NScott Feldman <scofeldm@cisco.com>
Signed-off-by: NVasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: NRoopa Prabhu <roprabhu@cisco.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Hardware has the loopback capability to queue the packets transmitted from
a device to the receive queue of the same device. enic now supports the
loopback capability.
Signed-off-by: NScott Feldman <scofeldm@cisco.com>
Signed-off-by: NVasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: NRoopa Prabhu <roprabhu@cisco.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change the receive queue buffer allocations into blocks of 32 entries when
ring size is less than 64, otherwise use 64 entries per block.
Signed-off-by: NScott Feldman <scofeldm@cisco.com>
Signed-off-by: NVasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: NRoopa Prabhu <roprabhu@cisco.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add new firmware devcmds - CMD_PROXY_BY_BDF, CMD_PACKET_FILTER_ALL,
CMD_ENABLE_WAIT.
Signed-off-by: NScott Feldman <scofeldm@cisco.com>
Signed-off-by: NVasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: NRoopa Prabhu <roprabhu@cisco.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace all printk routines with the (netdev|dev|pr)_<level> macros that
provide verbose logs.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NScott Feldman <scofeldm@cisco.com>
Signed-off-by: NVasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: NRoopa Prabhu <roprabhu@cisco.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add wrapper routines that issue devcmds to firmware and ensure that a
devcmd lock is held for each devcmd call.
Signed-off-by: NScott Feldman <scofeldm@cisco.com>
Signed-off-by: NVasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: NRoopa Prabhu <roprabhu@cisco.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The port profile information for a dynamic enic device is set by the upper
layers, that are oblivious to the device reset operation. We do not want a
reset operation erase the network state of a dynamic enic device as there
is no way to set up the port profile information again. Hence a lighter
reset operation called hang reset is used. Hang reset, unlike soft reset
does not reset the network state and resets the host side state only.
Signed-off-by: NScott Feldman <scofeldm@cisco.com>
Signed-off-by: NVasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: NRoopa Prabhu <roprabhu@cisco.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current ingress vlan rewrite mode setting lets the hardware strip off
the tag control information of a packet received on native vlan. As a
result, the priority bits are also lost. The fix is to change the ingress
vlan rewrite mode setting such that the complete tag control information is
retained for packets that belong to native vlan.
Signed-off-by: NScott Feldman <scofeldm@cisco.com>
Signed-off-by: NVasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: NRoopa Prabhu <roprabhu@cisco.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

enic now uses the GRO mechanism instead of LRO to pass skbs to upper
layers.
Signed-off-by: NScott Feldman <scofeldm@cisco.com>
Signed-off-by: NVasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: NRoopa Prabhu <roprabhu@cisco.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This eliminates some of the duplicate code for the various devices
that require the same basic kcq handling.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

By doing more work in the common function cnic_get_kcqes(), and
making full use of the kcq_info structure.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

By creating a common data stucture kcq_info for all devices, the kcq
(kernel completion queue) for all devices can be allocated by common
code.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

By creating a common cnic_doirq().
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current code makes assumptions about the CID (context ID) memory
space and starting CID that may not be always correct when firmware
changes.  In particular, BNX2_ISCSI_START_CID may not always be fixed.
We now calculate cp->max_cid_space and cp->iscsi_start_cid dynamically
instead of using fixed constants.  The unused cp->max_iscsi_conn is also
eliminated.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace EFX_ERR() with netif_err(), EFX_INFO() with netif_info(),
EFX_LOG() with netif_dbg() and EFX_TRACE() and EFX_REGDUMP() with
netif_vdbg().

Replace EFX_ERR_RL(), EFX_INFO_RL() and EFX_LOG_RL() using explicit
calls to net_ratelimit().

Implement the ethtool operations to get and set message level flags,
and add a 'debug' module parameter for the initial value.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Acked-by: NJeff Garzik <jgarzik@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the 5241 PHY ID to the broadcom module.
Signed-off-by: NDmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move all PHY IDs to brcmphy.h header for completeness and unification of code.
Signed-off-by: NDmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

sky2_phy_reinit is called by the ethtool helpers sky2_set_settings,
sky2_nway_reset and sky2_set_pauseparam when netif_running.

However, at the end of sky2_phy_init GM_GP_CTRL has GM_GPCR_RX_ENA and
GM_GPCR_TX_ENA cleared. So, doing these commands causes the device to
stop working:

$ ethtool -r eth0
$ ethtool -A eth0 autoneg off

Fix this issue by enabling Rx/Tx after running sky2_phy_init in
sky2_phy_reinit.
Signed-off-by: NBrandon Philips <bphilips@suse.de>
Tested-by: NBrandon Philips <bphilips@suse.de>
Cc: stable@kernel.org
Tested-by: NMike McCormack <mikem@ring3k.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For z/VM guest operating systems, OSX CHPIDs can only be used, if
LPAR and z/VM userID are explicitly authorized through the Service
Element. Issue a message if this SE-authorization is missing.
Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com>
Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

OSN devices use the same function level as OSD devices. This patch
adds OSN-devices to the initialization function for func_level.
Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com>
Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Turning on memory debugging showed there could be page breaks in
hardware headers. OSA does not allow this so we had to add code
to bounce the header in case there is a page break. This patch also
fixes a problem in case the skb->data part of a fragmented skb
spreads multiple pages.
Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The function qeth_free_buffer_pool is called _after_ the per-card
debug area has been released. This debug message is not all that
usefull anyway, and thus gets removed.
Signed-off-by: NCarsten Otte <cotte@de.ibm.com>
Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch removes the qerr debug area. Most info that goes in here is logged
to the card's local debug area already, those duplicates are removed. All other
elements are moved to the card's local debug area.
Signed-off-by: NCarsten Otte <cotte@de.ibm.com>
Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch removes the misc debug area. Instead of logging the entire skb
we just log a pointer to it into the card's local debug area in
qeth_core_get_next_skb. Other then that, this debug area is not used anywhere.
Signed-off-by: NCarsten Otte <cotte@de.ibm.com>
Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch removes the sense debug area completely. Despite the name this
debug area makes no sense at all because it's unused completely. Ouch.
Signed-off-by: NCarsten Otte <cotte@de.ibm.com>
Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch removes the qeth_trace debug area. All relevant data is logged into
either qeth_setup or into each card's own debug area. Superfluous information
(such as the card number when logging into the card's own debug area) is
removed without replacement.
Signed-off-by: NCarsten Otte <cotte@de.ibm.com>
Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds a debug area for each qeth card. This debug area will replace
various other debug areas that are global for all cards handled by the device
driver. On crash dump analysis this makes life easier when trying to find out
what's going on with an interface. Also, the forest of debug areas for this
device driver is significantly cleared up.
Signed-off-by: NCarsten Otte <cotte@de.ibm.com>
Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch decouples qeth_dbf_longtext from qeth's static debug array. The
function only uses one member anyway.
Signed-off-by: NCarsten Otte <cotte@de.ibm.com>
Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If another smsgiucv_app device exists, suspend / resume fails with
iucv path list corruption, because the same iucv_path_connect is
called twice.
The patch introduces a flag to save connect status of the smsgiucv
path to make sure iucv_path_connect in smsg_pm_restore_thaw is
called only once.
Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com>
Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After destroying recv ctx, context state remain same.
Fix it by marking as FREED.
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Offload tx timeout recovery to fw recovery func(check_health).
In check_health, first check health of device, if it its ok, then
do tx timeout recovery otherwise device recovery.
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is no need to free/alloc host resources during firmware
recovery.
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>