Skip to content

R
raspberrypi-kernel

openeuler / raspberrypi-kernel

通知 13
Star 1
Fork 0
R
raspberrypi-kernel
切换分支/标签
  1. 19 12月, 2011 3 次提交
    • D
      powerpc/mm: Fix section mismatch for mark_reserved_regions_for_nid · 28e86bdb
      由 David Rientjes 提交于 
      mark_reserved_regions_for_nid() is only called from do_init_bootmem(),
which is in .init.text, so it must be in the same section to avoid a
section mismatch warning.
Reported-by: NSubrata Modak <subrata@linux.vnet.ibm.com>
Signed-off-by: NDavid Rientjes <rientjes@google.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
      28e86bdb
    • M
      powerpc: Add __SANE_USERSPACE_TYPES__ to asm/types.h for LL64 · 2c9c6ce0
      由 Matt Evans 提交于 
      PPC64 uses long long for u64 in the kernel, but powerpc's asm/types.h
prevents 64-bit userland from seeing this definition, instead defaulting
to u64 == long in userspace.  Some user programs (e.g. kvmtool) may actually
want LL64, so this patch adds a check for __SANE_USERSPACE_TYPES__ so that,
if defined, int-ll64.h is included instead.
Signed-off-by: NMatt Evans <matt@ozlabs.org>
Acked-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
      2c9c6ce0
    • A
      powerpc: POWER7 optimised copy_to_user/copy_from_user using VMX · a66086b8
      由 Anton Blanchard 提交于 
      Implement a POWER7 optimised copy_to_user/copy_from_user using VMX.
For large aligned copies this new loop is over 10% faster, and for
large unaligned copies it is over 200% faster.

If we take a fault we fall back to the old version, this keeps
things relatively simple and easy to verify.

On POWER7 unaligned stores rarely slow down - they only flush when
a store crosses a 4KB page boundary. Furthermore this flush is
handled completely in hardware and should be 20-30 cycles.

Unaligned loads on the other hand flush much more often - whenever
crossing a 128 byte cache line, or a 32 byte sector if either sector
is an L1 miss.

Considering this information we really want to get the loads aligned
and not worry about the alignment of the stores. Microbenchmarks
confirm that this approach is much faster than the current unaligned
copy loop that uses shifts and rotates to ensure both loads and
stores are aligned.

We also want to try and do the stores in cacheline aligned, cacheline
sized chunks. If the store queue is unable to merge an entire
cacheline of stores then the L2 cache will have to do a
read/modify/write. Even worse, we will serialise this with the stores
in the next iteration of the copy loop since both iterations hit
the same cacheline.

Based on this, the new loop does the following things:

1 - 127 bytes
Get the source 8 byte aligned and use 8 byte loads and stores. Pretty
boring and similar to how the current loop works.

128 - 4095 bytes
Get the source 8 byte aligned and use 8 byte loads and stores,
1 cacheline at a time. We aren't doing the stores in cacheline
aligned chunks so we will potentially serialise once per cacheline.
Even so it is much better than the loop we have today.

4096 - bytes
If both source and destination have the same alignment get them both
16 byte aligned, then get the destination cacheline aligned. Do
cacheline sized loads and stores using VMX.

If source and destination do not have the same alignment, we get the
destination cacheline aligned, and use permute to do aligned loads.

In both cases the VMX loop should be optimal - we always do aligned
loads and stores and are always doing stores in cacheline aligned,
cacheline sized chunks.

To be able to use VMX we must be careful about interrupts and
sleeping. We don't use the VMX loop when in an interrupt (which should
be rare anyway) and we wrap the VMX loop in disable/enable_pagefault
and fall back to the existing copy_tofrom_user loop if we do need to
sleep.

The VMX breakpoint of 4096 bytes was chosen using this microbenchmark:

http://ozlabs.org/~anton/junkcode/copy_to_user.c

Since we are using VMX and there is a cost to saving and restoring
the user VMX state there are two broad cases we need to benchmark:

- Best case - userspace never uses VMX

- Worst case - userspace always uses VMX

In reality a userspace process will sit somewhere between these two
extremes. Since we need to test both aligned and unaligned copies we
end up with 4 combinations. The point at which the VMX loop begins to
win is:

0% VMX
aligned		2048 bytes
unaligned	2048 bytes

100% VMX
aligned		16384 bytes
unaligned	8192 bytes

Considering this is a microbenchmark, the data is hot in cache and
the VMX loop has better store queue merging properties we set the
breakpoint to 4096 bytes, a little below the unaligned breakpoints.

Some future optimisations we can look at:

- Looking at the perf data, a significant part of the cost when a
  task is always using VMX is the extra exception we take to restore
  the VMX state. As such we should do something similar to the x86
  optimisation that restores FPU state for heavy users. ie:

        /*
         * If the task has used fpu the last 5 timeslices, just do a full
         * restore of the math state immediately to avoid the trap; the
         * chances of needing FPU soon are obviously high now
         */
        preload_fpu = tsk_used_math(next_p) && next_p->fpu_counter > 5;

  and

        /*
         * fpu_counter contains the number of consecutive context switches
         * that the FPU is used. If this is over a threshold, the lazy fpu
         * saving becomes unlazy to save the trap. This is an unsigned char
         * so that after 256 times the counter wraps and the behavior turns
         * lazy again; this to deal with bursty apps that only use FPU for
         * a short time
         */

- We could create a paca bit to mirror the VMX enabled MSR bit and check
  that first, avoiding multiple calls to calling enable_kernel_altivec.
  That should help with iovec based system calls like readv.

- We could have two VMX breakpoints, one for when we know the user VMX
  state is loaded into the registers and one when it isn't. This could
  be a second bit in the paca so we can calculate the break points quickly.

- One suggestion from Ben was to save and restore the VSX registers
  we use inline instead of using enable_kernel_altivec.

[BenH: Fixed a problem with preempt and fixed build without CONFIG_ALTIVEC]
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
      a66086b8
  3. 16 12月, 2011 8 次提交
  5. 09 12月, 2011 8 次提交
  7. 08 12月, 2011 21 次提交