According to section 4.5 of rfc7496, prsctp_enable should be per asoc.
We will add prsctp_enable to both asoc and ep, and replace the places
where it used net.sctp->prsctp_enable with asoc->prsctp_enable.

ep->prsctp_enable will be initialized with net.sctp->prsctp_enable, and
asoc->prsctp_enable will be initialized with ep->prsctp_enable. We can
also modify it's value through sockopt SCTP_PR_SUPPORTED.
Signed-off-by: NXin Long <lucien.xin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit 4386f566 ("net: ethernet: bcmgenet: use
phy_ethtool_{get|set}_link_ksettings")

This patch is wrong, the function phy_ethtool_{get|set}_link_ksettings
don't check if the device is running, but the driver bcmgenet need this
check.

The function {get|set}_settings need to access the mdio bus, and this
bus may only be used when the device is running. Otherwise, the clock
is disable and a mdio access will fail.
Signed-off-by: NPhilippe Reynes <tremyfr@gmail.com>
Acked-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Florian Fainelli says:

====================
net: dsa: b53: Add Broadcom NSP switch support

This patch series updates the B53 driver to support Broadcom's Northstar Plus
Soc integrated switch.

Unlike the version of the core present in BCM5301x/Northstar, we cannot read the
full chip id of the switch, so we need to get the information about our switch
id from Device Tree.

Other than that, this is a regular Broadcom Ethernet switch which is register
compatible for all practical purposes with the existing switch driver.

Since DSA requires a working CPU Ethernet MAC driver this depends on Jon
Mason's AMAC/BGMAC driver changes to support NSP. Board specific changes depend
on patches present in Broadcom's ARM SoC branches and will be posted in a short
while.
====================
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Update the SRAB, core driver and binding document to support the
BCM585xx/586xx/88312 integrated switch (Northstar Plus SoCs family).
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For Northstart Plus SoCs, we cannot detect the switch because only the
revision information is provied in the Management page, instead, rely on
Device Tree to tell us the chip id, and pass it down using the
b53_platform_data structure.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds support for TSE PCS that uses SGMII adapter when the phy-mode of
the dwmac is set to sgmii.
Signed-off-by: NTien Hock Loh <thloh@altera.com>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

All inet6_netconf_notify_devconf() callers are in process context,
so we can use GFP_KERNEL allocations if we take care of not holding
a rwlock while not needed in ip6mr (we hold RTNL there)

Fixes: d67b8c61 ("netconf: advertise mc_forwarding status")
Fixes: f3a1bfb1 ("rtnl/ipv6: use netconf msg to advertise forwarding status")
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: NNicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

inet_forward_change() runs with RTNL held.
We are allowed to sleep if required.

If we use __in_dev_get_rtnl() instead of __in_dev_get_rcu(),
we no longer have to use GFP_ATOMIC allocations in
inet_netconf_notify_devconf(), meaning we are less likely to miss
notifications under memory pressure, and wont touch precious memory
reserves either and risk dropping incoming packets.

inet_netconf_get_devconf() can also use GFP_KERNEL allocation.

Fixes: edc9e748 ("rtnl/ipv4: use netconf msg to advertise forwarding status")
Fixes: 9e551110 ("rtnl/ipv4: add support of RTM_GETNETCONF")
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: NNicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jon Mason says:

====================
net: ethernet: bgmac: Add platform device support

David Miller, Please consider including patches 1-5 in net-next

Florian Fainelli, Please consider including patches 6 & 7 in
  devicetree/next

Changes in v2:
* Made device tree binding changes suggested by Sergei Shtylyov,
  Ray Jui, Rob Herring, Florian Fainelli, and Arnd Bergmann
* Removed devm_* error paths in the bgmac_platform.c suggested by
  Florian Fainelli
* Added Arnd Bergmann's Acked-by to the first 5 (there were changes
  outlined in the bullets above, but I believe them to be minor enough
  for him to not revoke his acks)

This patch series adds support for other, non-bcma iProc SoC's to the
bgmac driver.  This series only adds NSP support, but we are interested
in adding support for the Cygnus and NS2 families (with more possible
down the road).

To support non-bcma enabled SoCs, we need to add the standard device
tree "platform device" support.  Unfortunately, this driver is very
tighly coupled with the bcma bus and much unwinding is needed.  I tried
to break this up into a number of patches to make it more obvious what
was being done to add platform device support.  I was able to verify
that the bcma code still works using a 53012K board (NS SoC), and that
the platform code works using a 58625K board (NSP SoC).
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The bcma portion of the driver has been split off into a bcma specific
driver.  This has been mirrored for the platform driver.  The last
references to the bcma core struct have been changed into a generic
function call.  These function calls are wrappers to either the original
bcma code or new platform functions that access the same areas via MMIO.
This necessitated adding function pointers for both platform and bcma to
hide which backend is being used from the generic bgmac code.
Signed-off-by: NJon Mason <jon.mason@broadcom.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Tested-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The bgmac driver is using the bcma provides device ID and revision, as
well as the SoC ID and package, to determine which features are
necessary to enable, reset, etc in the driver.   In anticipation of
removing the bcma requirement for this driver, these must be changed to
not reference that struct.  In place of that, each "feature" has been
given a flag, and the flags are enabled for their respective device and
SoC.
Signed-off-by: NJon Mason <jon.mason@broadcom.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Tested-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move the BCMA MDIO phy into a separate file, as it is very tightly
coupled with the BCMA bus.  This will help with the upcoming BCMA
removal from the bgmac driver.  Optimally, this should be moved into
phy drivers, but it is too tightly coupled with the bgmac driver to
effectively move it without more changes to the driver.

Note: the phy_reset was intentionally removed, as the mdio phy subsystem
automatically resets the phy if a reset function pointer is present.  In
addition to the moving of the driver, this reset function is added.
Signed-off-by: NJon Mason <jon.mason@broadcom.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Tested-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The dma buffer allocation, etc references a dma_dev device pointer from
the bcma core.  In anticipation of removing the bcma requirement for
this driver, these must be changed to not reference that struct.  Add a
dma_dev device pointer to the bgmac stuct and reference that instead.
Signed-off-by: NJon Mason <jon.mason@broadcom.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Tested-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The bgmac_* print wrappers call dev_* prints with the dev pointer from
the bcma core.  In anticipation of removing the bcma requirement for
this driver, these must be changed to not reference that struct.  So,
simply change all of the bgmac_* prints to their dev_* counterparts.  In
some cases netdev_* prints are more appropriate, so change those as
well.
Signed-off-by: NJon Mason <jon.mason@broadcom.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Tested-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

An important information for the napi_poll tracepoint is knowing
the work done (packets processed) by the napi_poll() call. Add
both the work done and budget, as they are related.

Handle trace_napi_poll() param change in dropwatch/drop_monitor
and in python perf script netdev-times.py in backward compat way,
as python fortunately supports optional parameter handling.
Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Hayes Wang says:

====================
r8152: remove the redundant code

Remove the unnacessary code.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is no conflict between the work_queue function and
rtl8152_set_speed(), so we don't have to cancel the delayed work in
rtl8152_set_speed().
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After commit 90186af4 ("r8152: fix lockup when runtime PM is enabled"),
the autoresume wouldn't start the device before rtl8152_open() is finished.
Therefore, we don't have to reset the linking status before and after
autoresume. That is, one of netif_carrier_off() in rtl8152_open() could be
removed.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In rtl_hw_phy_work_func_t(), the flag of PHY_RESET is set in
rtl_ops.hw_phy_cfg() and cleared in rtl8152_set_speed(). Therefore,
the rtl_phy_reset() is never run and is unnecessary.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Simon Horman says:

====================
net: support MPLS in IPv4 and UDP

This short series provides support for MPLS in IPv4 (RFC4023), and by
virtue of FOU, MPLS in UDP (RFC7510).

The changes are as follows:
1. Teach tunnel4.c about AF_MPLS, it already understands AF_INET and
   AF_INET6
2. Enhance IPIP and SIT to handle MPLS. Both already handle IPv4.
   SIT also already handles IPv6.
3. Trivially enhance MPLS to allow routes over SIT and IPIP tunnels.

A corresponding patch set for iproute2 has also been provided.

Changes since v1
* Correct inverted IPIP protocol logic in SIT patch
* Provide usage example below

Sample configuration follows:

* The following creates a tunnel and routes MPLS packets whose outermost
  label is 100 over it. The forwarded packets will have the outermost label
  stack entry, 100, removed and two label stack entries added, the
  outermost having label 200 and the next having label 300.

  The local end-point for the tunnel is 10.0.99.192 and the remote
  endpoint is 10.0.99.193.

  The local address for encapsulated packets is 10.0.98.192 and the
  remote address is 10.0.98.193.

  # Create an MPLS over IPv4 tunnel using the IPIP driver
  ip link add name tun1 type ipip remote 10.0.99.193 local 10.0.99.192 \
	ttl 225 mode mplsip

  # Bring the tunnel up and an add an IPv4 address and route
  ip link set up dev tun1
  ip addr add 10.0.98.192/24 dev tun1

  # Set MPLS route
  # Allow MPLS forwarding of packets recieved on eth0
  echo 1 > /proc/sys/net/mpls/conf/eth0/input
  # Larger than label to be routed (100)
  echo 101 > /proc/sys/net/mpls/platform_labels
  ip -f mpls route add 100 as 200/300 via inet 10.0.98.193

* For FOU (in this case MPLS over UDP) a tunnel may created using:

  # Packets recieved on UDP port 6635 are MPLS over UDP (IP proto 137)
  ip fou add port 6635 ipproto 137
  # Create the tunnel netdev
  ip link add name tun1 type ipip remote 10.0.99.193 local 10.0.99.192 \
	ttl 225 mode mplsip encap fou encap-sport auto encap-dport 6635

  IPv4 address, link and route, and MPLS routing commands are as per
  the MPLS over IPv4 example

* To use the SIT driver instead of the IPIP driver "ipip" may be substituted
  for "sit" in the above examples.

* To create a tunnel that forwards and receives all supported
  inner-protocols "mplsip" may be substituted for "any" in the above
  examples.

  For the IPIP driver this configures both IPv4 and MPLS over IPv4.
  For the SIT driver this configures IPv6, IPv4 and MPLS over IPv4.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allow MPLS routes on IPIP and SIT devices now that they
support forwarding MPLS packets.
Signed-off-by: NSimon Horman <simon.horman@netronome.com>
Reviewed-by: NDinan Gunawardena <dinan.gunawardena@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Extend the IPIP driver to support MPLS over IPv4. The implementation is an
extension of existing support for IPv4 over IPv4 and is based of multiple
inner-protocol support for the SIT driver.
Signed-off-by: NSimon Horman <simon.horman@netronome.com>
Reviewed-by: NDinan Gunawardena <dinan.gunawardena@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Extend the SIT driver to support MPLS over IPv4. This implementation
extends existing support for IPv6 over IPv4 and IPv4 over IPv4.
Signed-off-by: NSimon Horman <simon.horman@netronome.com>
Reviewed-by: NDinan Gunawardena <dinan.gunawardena@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Extend tunnel support to MPLS over IPv4.  The implementation extends the
existing differentiation between IPIP and IPv6 over IPv4 to also cover MPLS
over IPv4.
Signed-off-by: NSimon Horman <simon.horman@netronome.com>
Reviewed-by: NDinan Gunawardena <dinan.gunawardena@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As was suggested this patch adds support for the different versions of MLD
and IGMP query types. Since the user visible structure is still in net-next
we can augment it instead of adding netlink attributes.
The distinction between the different IGMP/MLD query types is done as
suggested in Section 7.1, RFC 3376 [1] and Section 8.1, RFC 3810 [2] based
on query payload size and code for IGMP. Since all IGMP packets go through
multicast_rcv() and it uses ip_mc_check_igmp/ipv6_mc_check_mld we can be
sure that at least the ip/ipv6 header can be directly used.

[1] https://tools.ietf.org/html/rfc3376#section-7
[2] https://tools.ietf.org/html/rfc3810#section-8.1Suggested-by: NLinus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: NNikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: NStephen Hemminger <stephen@networkplumber.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When we introduced GSO support, if using auth the auth chunk was being
left queued on the packet even after the final segment was generated.
Later on sctp_transmit_packet it calls sctp_packet_reset, which zeroed
the packet len while not accounting for this left-over. This caused more
space to be used the next packet due to the chunk still being queued,
but space which wasn't allocated as its size wasn't accounted.

The fix is to only queue it back when we know that we are going to
generate another segment.

Fixes: 90017acc ("sctp: Add GSO support")
Signed-off-by: NMarcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This code generates as static checker warning because htons(ETH_P_IPV6)
is always true.  From the context it looks like the && was intended to
be !=.

Fixes: 94758f8d ('bnxt_en: Add GRO logic for BCM5731X chips.')
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

over time there were multiple requests to access different data
structures and fields of task_struct current, so finally add
the helper to access 'current' as-is. Tracing bpf programs will do
the rest of walking the pointers via bpf_probe_read().
Note that current can be null and bpf program has to deal it with,
but even dumb passing null into bpf_probe_read() is still safe.
Suggested-by: NBrendan Gregg <brendan.d.gregg@gmail.com>
Signed-off-by: NAlexei Starovoitov <ast@kernel.org>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The routing table of every switch in a tree is currently initialized to
all zeros. This is an issue since 0 is a valid port number.

Add a DSA_RTABLE_NONE=-1 constant to initialize the signed values of the
routing table pointing to other switches.

This fixes the device mapping of the mv88e6xxx driver where the port
pointing to the switch itself and to non-existent switches was wrongly
configured to be 0. It is now set to the expected 0xf value.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The referenced change added a netlink notifier for processing
device queue size events.  These events are fired for all devices
but the registered callback assumed they only occurred for tun
devices.  This fix adds a check (borrowed from macvtap.c) to discard
non-tun device events.

For reference, this fixes the following splat:
[   71.505935] BUG: unable to handle kernel NULL pointer dereference at 0000000000000010
[   71.513870] IP: [<ffffffff8153c1a0>] tun_device_event+0x110/0x340
[   71.519906] PGD 3f41f56067 PUD 3f264b7067 PMD 0
[   71.524497] Oops: 0002 [#1] SMP DEBUG_PAGEALLOC
[   71.529374] gsmi: Log Shutdown Reason 0x03
[   71.533417] Modules linked in:[   71.533826] mlx4_en: eth1: Link Up

[   71.539616]  bonding w1_therm wire cdc_acm ehci_pci ehci_hcd mlx4_en ib_uverbs mlx4_ib ib_core mlx4_core
[   71.549282] CPU: 12 PID: 7915 Comm: set.ixion-haswe Not tainted 4.7.0-dbx-DEV #8
[   71.556586] Hardware name: Intel Grantley,Wellsburg/Ixion_IT_15, BIOS 2.58.0 05/03/2016
[   71.564495] task: ffff887f00bb20c0 ti: ffff887f00798000 task.ti: ffff887f00798000
[   71.571894] RIP: 0010:[<ffffffff8153c1a0>]  [<ffffffff8153c1a0>] tun_device_event+0x110/0x340
[   71.580327] RSP: 0018:ffff887f0079bbd8  EFLAGS: 00010202
[   71.585576] RAX: fffffffffffffae8 RBX: ffff887ef6d03378 RCX: 0000000000000000
[   71.592624] RDX: 0000000000000000 RSI: 0000000000000028 RDI: 0000000000000000
[   71.599675] RBP: ffff887f0079bc48 R08: 0000000000000000 R09: 0000000000000001
[   71.606730] R10: 0000000000000004 R11: 0000000000000000 R12: 0000000000000010
[   71.613780] R13: 0000000000000000 R14: 0000000000000001 R15: ffff887f0079bd00
[   71.620832] FS:  00007f5cdc581700(0000) GS:ffff883f7f700000(0000) knlGS:0000000000000000
[   71.628826] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[   71.634500] CR2: 0000000000000010 CR3: 0000003f3eb62000 CR4: 00000000001406e0
[   71.641549] Stack:
[   71.643533]  ffff887f0079bc08 0000000000000246 000000000000001e ffff887ef6d00000
[   71.650871]  ffff887f0079bd00 0000000000000000 0000000000000000 ffffffff00000000
[   71.658210]  ffff887f0079bc48 ffffffff81d24070 00000000fffffff9 ffffffff81cec7a0
[   71.665549] Call Trace:
[   71.667975]  [<ffffffff810eeb0d>] notifier_call_chain+0x5d/0x80
[   71.673823]  [<ffffffff816365d0>] ? show_tx_maxrate+0x30/0x30
[   71.679502]  [<ffffffff810eeb3e>] __raw_notifier_call_chain+0xe/0x10
[   71.685778]  [<ffffffff810eeb56>] raw_notifier_call_chain+0x16/0x20
[   71.691976]  [<ffffffff8160eb30>] call_netdevice_notifiers_info+0x40/0x70
[   71.698681]  [<ffffffff8160ec36>] call_netdevice_notifiers+0x16/0x20
[   71.704956]  [<ffffffff81636636>] change_tx_queue_len+0x66/0x90
[   71.710807]  [<ffffffff816381ef>] netdev_store.isra.5+0xbf/0xd0
[   71.716658]  [<ffffffff81638350>] tx_queue_len_store+0x50/0x60
[   71.722431]  [<ffffffff814a6798>] dev_attr_store+0x18/0x30
[   71.727857]  [<ffffffff812ea3ff>] sysfs_kf_write+0x4f/0x70
[   71.733274]  [<ffffffff812e9507>] kernfs_fop_write+0x147/0x1d0
[   71.739045]  [<ffffffff81134a4f>] ? rcu_read_lock_sched_held+0x8f/0xa0
[   71.745499]  [<ffffffff8125a108>] __vfs_write+0x28/0x120
[   71.750748]  [<ffffffff8111b137>] ? percpu_down_read+0x57/0x90
[   71.756516]  [<ffffffff8125d7d8>] ? __sb_start_write+0xc8/0xe0
[   71.762278]  [<ffffffff8125d7d8>] ? __sb_start_write+0xc8/0xe0
[   71.768038]  [<ffffffff8125bd5e>] vfs_write+0xbe/0x1b0
[   71.773113]  [<ffffffff8125c092>] SyS_write+0x52/0xa0
[   71.778110]  [<ffffffff817528e5>] entry_SYSCALL_64_fastpath+0x18/0xa8
[   71.784472] Code: 45 31 f6 48 8b 93 78 33 00 00 48 81 c3 78 33 00 00 48 39 d3 48 8d 82 e8 fa ff ff 74 25 48 8d b0 40 05 00 00 49 63 d6 41 83 c6 01 <49> 89 34 d4 48 8b 90 18 05 00 00 48 39 d3 48 8d 82 e8 fa ff ff
[   71.803655] RIP  [<ffffffff8153c1a0>] tun_device_event+0x110/0x340
[   71.809769]  RSP <ffff887f0079bbd8>
[   71.813213] CR2: 0000000000000010
[   71.816512] ---[ end trace 4db6449606319f73 ]---

Fixes: 1576d986 ("tun: switch to use skb array for tx")
Signed-off-by: NCraig Gallek <kraig@google.com>
Acked-by: NJason Wang <jasowang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Merge tag 'rxrpc-rewrite-20160706' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs

David Howells says:

====================
rxrpc: Improve conn/call lookup and fix call number generation [ver #3]

I've fixed a couple of patch descriptions and excised the patch that
duplicated the connections list for reconsideration at a later date.

For reference, the excised patch is sitting on the rxrpc-experimental
branch of my git tree, based on top of the rxrpc-rewrite branch.  Diffing
it against yesterday's tag shows no differences.

Would you prefer the patch set to be emailed afresh instead of a git-pull
request?

David
---
Here's the next part of the AF_RXRPC rewrite.  The two main purposes of
this set are to fix the call number handling and to make use of RCU when
looking up the connection or call to pass a received packet to.

Important changes in this set include:

 (1) Avoidance of placing stack data into SG lists in rxkad so that kernel
     stacks can become vmalloc'd (Herbert Xu).

 (2) Calls cease pinning the connection they used as soon as possible,
     which allows the connection to be discarded sooner and allows the call
     channel on that connection to be reused earlier.

 (3) Make each call channel on a connection have a separate and independent
     call number space rather than having a shared number space for the
     connection.  Call numbers should increment monotonically per channel
     on the client, and the server should ignore a call with a lower call
     number for that channel than the latest it has seen.  The RESPONSE
     packet sets the minimum values of each call ID counter on a
     connection.

 (4) Look up calls by indexing the channel array on a connection rather
     than by keeping calls in an rbtree on that connection.  Also look up
     calls using the channel array rather than using a hashtable.

     The call hashtable can then be removed.

 (5) Call terminal statuses are cached in the channel array for the last
     call.  It is assumed that if we the server have seen call N, then the
     client no longer cares about call N-1 on the same channel.

     This will allow retransmission of the terminal status in future
     without the need to keep the rxrpc_call struct around.

 (6) Peer lookups are moved out of common connection handling code and into
     service connection handling code as client connections (a) must point
     to a peer before they can be used and (b) are looked up by a
     machine-unique connection ID directly, so we only need to look up the
     peer first if we're going to deal with a service call.

 (7) The reference count on a connection is held elevated by 1 whilst it is
     alive (ie. idle unused connections have a refcount of 1).  The reaper
     will attempt to change the refcount from 1->0 and skip if this cannot
     be done, whilst look ups only increment the refcount if it's non-zero.

     This makes the implementation of RCU lookups easier as we don't have
     to get a ref on the connection or a lock on the connection list to
     prevent a connection being reaped whilst we're contemplating queueing
     a packet that initiates a new service call upon it.

     If we need to get a connection, but there's a dead connection in the
     tree, we use rb_replace_node() to replace the dead one with a new one.

 (8) Use a seqlock to validate the walk over the service connection rbtree
     attached to a peer when it's being walked in RCU mode.

 (9) Make the incoming call/connection packet handling code use RCU mode
     and locks and make it only take a reference if the call/connection
     gets queued on a workqueue.

The intention is that the next set will introduce the connection lifetime
management and capacity limits to prevent clients from overloading the
server.

There are some fixes too:

 (1) Verifying that a packet coming in to a client connection came from the
     expected source.

 (2) Fix handling of connection failure in client call creation where we
     don't reinitialise the list linkage block and a second attempt to
     unlink the failed connection oopses and also we don't set the state
     correctly, which causes an assertion failure.

 (3) New service calls were being added to the socket's accept queue under
     the wrong lock.

Changes:

 (V2) In rxrpc_find_service_conn_rcu() initialised the sequence number to 0.

      Fixed the RCU handling in conn_service.c by introducing and using
      rb_replace_node_rcu() as an RCU-safe alternative in
      rxrpc_publish_service_conn().

      Modified and used rcu_dereference_raw() to avoid RCU sparse warnings
      in rxrpc_find_service_conn_rcu().

      Added in some missing RCU dereference wrappers.  It seems to be
      necessary to turn on CONFIG_PROVE_RCU_REPEATEDLY as well as
      CONFIG_SPARSE_RCU_POINTER to get the static __rcu annotation checking
      to happen.

      Fixed some other sparse warnings, including a missing ntohs() in
      jumbo packet processing.

 (V3) Fixed some commit descriptions.

      Excised the patch that duplicated the connection list to separate out
      the procfs list for reconsideration at a later date.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the new APIs for eliminating a copy on the receive path. These new APIs also
help in minimizing the number of memory barriers we end up issuing (in the
ringbuffer code) since we can better control when we want to expose the ring
state to the host.

The patch is being resent to address earlier email issues.
Signed-off-by: NK. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

hfsc_sched is huge (size: 920, cachelines: 15), but we can get it to 14
cachelines by placing level after filter_cnt (covering 4 byte hole) and
reducing period/nactive/flags to u32 (period is just a counter,
incremented when class becomes active -- 2**32 is plenty for this
purpose, also, long is only 32bit wide on 32bit platforms anyway).

cl_vtperiod is exported to userspace via tc_hfsc_stats, but its period
member is already u32, so no precision is lost there either.

Cc: Michal Soltys <soltys@ziu.info>
Signed-off-by: NFlorian Westphal <fw@strlen.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Merge tag 'mac80211-next-for-davem-2016-07-06' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next

Johannes Berg says:

====================
One more set of new features:
 * beacon report (for radio measurement) support in cfg80211/mac80211
 * hwsim: allow wmediumd in namespaces
 * mac80211: extend 160MHz workaround to CSA IEs
 * mesh: properly encrypt group-addressed privacy action frames
 * mesh: allow setting peer AID
 * first steps for MU-MIMO monitor mode
 * along with various other cleanups and improvements
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove .owner field since calls to module_platform_driver() will
set it automatically.
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Conflicts:
	drivers/net/ethernet/mellanox/mlx5/core/en.h
	drivers/net/ethernet/mellanox/mlx5/core/en_main.c
	drivers/net/usb/r8152.c

All three conflicts were overlapping changes.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pull networking fixes from David Miller:

 1) All users of AF_PACKET's fanout feature want a symmetric packet
    header hash for load balancing purposes, so give it to them.

 2) Fix vlan state synchronization in e1000e, from Jarod Wilson.

 3) Use correct socket pointer in ip_skb_dst_mtu(), from Shmulik
    Ladkani.

 4) mlx5 bug fixes from Mohamad Haj Yahia, Daniel Jurgens, Matthew
    Finlay, Rana Shahout, and Shaker Daibes.  Mostly to do with
    operation timeouts and PCI error handling.

 5) Fix checksum handling in mirred packet action, from WANG Cong.

 6) Set skb->dev correctly when transmitting in !protect_frames case of
    macsec driver, from Daniel Borkmann.

 7) Fix MTU calculation in geneve driver, from Haishuang Yan.

 8) Missing netif_napi_del() in unregister path of qeth driver, from
    Ursula Braun.

 9) Handle malformed route netlink messages in decnet properly, from
    Vergard Nossum.

10) Memory leak of percpu data in ipv6 routing code, from Martin KaFai
    Lau.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (41 commits)
  ipv6: Fix mem leak in rt6i_pcpu
  net: fix decnet rtnexthop parsing
  cxgb4: update latest firmware version supported
  net/mlx5: Avoid setting unused var when modifying vport node GUID
  bonding: fix enslavement slave link notifications
  r8152: fix runtime function for RTL8152
  qeth: delete napi struct when removing a qeth device
  Revert "fsl/fman: fix error handling"
  fsl/fman: fix error handling
  cdc_ncm: workaround for EM7455 "silent" data interface
  RDS: fix rds_tcp_init() error path
  geneve: fix max_mtu setting
  net: phy: dp83867: Fix initialization of PHYCR register
  enc28j60: Fix race condition in enc28j60 driver
  net: stmmac: Fix null-function call in ISR on stmmac1000
  tipc: fix nl compat regression for link statistics
  net: bcmsysport: Device stats are unsigned long
  macsec: set actual real device for xmit when !protect_frames
  net_sched: fix mirrored packets checksum
  packet: Use symmetric hash for PACKET_FANOUT_HASH.
  ...

Pablo Neira Ayuso says:

====================
Netfilter updates for net-next

The following patchset contains Netfilter updates for net-next,
they are:

1) Don't use userspace datatypes in bridge netfilter code, from
   Tobin Harding.

2) Iterate only once over the expectation table when removing the
   helper module, instead of once per-netns, from Florian Westphal.

3) Extra sanitization in xt_hook_ops_alloc() to return error in case
   we ever pass zero hooks, xt_hook_ops_alloc():

4) Handle NFPROTO_INET from the logging core infrastructure, from
   Liping Zhang.

5) Autoload loggers when TRACE target is used from rules, this doesn't
   change the behaviour in case the user already selected nfnetlink_log
   as preferred way to print tracing logs, also from Liping Zhang.

6) Conntrack slabs with SLAB_HWCACHE_ALIGN to allow rearranging fields
   by cache lines, increases the size of entries in 11% per entry.
   From Florian Westphal.

7) Skip zone comparison if CONFIG_NF_CONNTRACK_ZONES=n, from Florian.

8) Remove useless defensive check in nf_logger_find_get() from Shivani
   Bhardwaj.

9) Remove zone extension as place it in the conntrack object, this is
   always include in the hashing and we expect more intensive use of
   zones since containers are in place. Also from Florian Westphal.

10) Owner match now works from any namespace, from Eric Bierdeman.

11) Make sure we only reply with TCP reset to TCP traffic from
    nf_reject_ipv4, patch from Liping Zhang.

12) Introduce --nflog-size to indicate amount of network packet bytes
    that are copied to userspace via log message, from Vishwanath Pai.
    This obsoletes --nflog-range that has never worked, it was designed
    to achieve this but it has never worked.

13) Introduce generic macros for nf_tables object generation masks.

14) Use generation mask in table, chain and set objects in nf_tables.
    This allows fixes interferences with ongoing preparation phase of
    the commit protocol and object listings going on at the same time.
    This update is introduced in three patches, one per object.

15) Check if the object is active in the next generation for element
    deactivation in the rbtree implementation, given that deactivation
    happens from the commit phase path we have to observe the future
    status of the object.

16) Support for deletion of just added elements in the hash set type.

17) Allow to resize hashtable from /proc entry, not only from the
    obscure /sys entry that maps to the module parameter, from Florian
    Westphal.

18) Get rid of NFT_BASECHAIN_DISABLED, this code is not exercised
    anymore since we tear down the ruleset whenever the netdevice
    goes away.

19) Support for matching inverted set lookups, from Arturo Borrero.

20) Simplify the iptables_mangle_hook() by removing a superfluous
    extra branch.

21) Introduce ether_addr_equal_masked() and use it from the netfilter
    codebase, from Joe Perches.

22) Remove references to "Use netfilter MARK value as routing key"
    from the Netfilter Kconfig description given that this toggle
    doesn't exists already for 10 years, from Moritz Sichert.

23) Introduce generic NF_INVF() and use it from the xtables codebase,
    from Joe Perches.

24) Setting logger to NONE via /proc was not working unless explicit
    nul-termination was included in the string. This fixes seems to
    leave the former behaviour there, so we don't break backward.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pull sound fixes from Takashi Iwai:
 "Here are a collection of small fixes: at this time, we've got a
  slightly high amount, but all small and trivial fixes, and nothing
  scary can be seen there"

* tag 'sound-4.7-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (21 commits)
  ALSA: hda/realtek: Add Lenovo L460 to docking unit fixup
  ALSA: timer: Fix negative queue usage by racy accesses
  ASoC: rt5645: fix reg-2f default value.
  ASoC: fsl_ssi: Fix number of words per frame for I2S-slave mode
  ALSA: au88x0: Fix calculation in vortex_wtdma_bufshift()
  ALSA: hda - Add PCI ID for Kabylake-H
  ALSA: echoaudio: Fix memory allocation
  ASoC: Intel: atom: fix missing breaks that would cause the wrong operation to execute
  ALSA: hda - fix read before array start
  ASoC: cx20442: set tty->receiver_room in v253_open
  ASoC: ak4613: Enable cache usage to fix crashes on resume
  ASoC: wm8940: Enable cache usage to fix crashes on resume
  ASoC: Intel: Skylake: Initialize module list for Broxton
  ASoC: wm5102: Correct supported channels on trace compressed DAI
  ASoC: wm5110: Add missing route from OUT3R to SYSCLK
  ASoC: rt5670: fix HP Playback Volume control
  ASoC: hdmi-codec: select CONFIG_HDMI
  ASoC: davinci-mcasp: Fix dra7 DMA offset when using CFG port
  ASoC: hdac_hdmi: Fix potential NULL dereference
  ASoC: ak4613: Remove owner assignment from platform_driver
  ...

Pull chrome platform fix from Olof Johansson:
 "A single fix this time, closing a window where ioctl args are fetched
  twice"

* tag 'chrome-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/olof/chrome-platform:
  platform/chrome: cros_ec_dev - double fetch bug in ioctl