Followup of commits 9d21493b
and 08baf561
(net: tx scalability works : trans_start)
(net: txq_trans_update() helper)

Now that core network takes care of trans_start updates, dont do it
in drivers themselves, if possible. Multi queue drivers can
avoid one cache miss (on dev->trans_start) in their start_xmit()
handler.

Exceptions are NETIF_F_LLTX drivers (vxge & tehuti)
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the i2400m is connected to a network, the host interface (USB)
cannot be suspended. For that to happen, the device has to have
negotiated with the basestation to put the link on IDLE state.

If the host tries to put the device in standby while it is connected
but not idle, the device resets, as the driver should not do that.

To avoid triggering that, when the USB susbsytem requires the driver
to autosuspend the device, the driver checks if the device is not yet
idle. If it is not, the request is requested (will be retried again
later on after the autosuspend timeout). At some point the device will
enter idle and the request will succeed (unless of course, there is
network traffic, but at that point, there is no idle neither in the
link or the host interface).
Signed-off-by: NInaky Perez-Gonzalez <inaky@linux.intel.com>

From a fix by Cindy H Kao:

  Block size has to be set before sending IOE enable because the
  firmware reads the block size register before it reads IOE register.
Signed-off-by: NInaky Perez-Gonzalez <inaky@linux.intel.com>

Functions i2400m_report_tlv*() are only called from
i2400m_report_hook(), called in a workqueue by
i2400m_report_hook_work(). The scheduler checks for device readiness
before scheduling.

Added an extra check for readiness in i2400m_report_hook_work(), which
makes all the checks down the line redundant.

Obviously the device state could change in the middle, but error
handling would take care of that.
Signed-off-by: NInaky Perez-Gonzalez <inaky@linux.intel.com>

i2400m_report_state_hook() is going to get messier as we add handling
code.
Signed-off-by: NInaky Perez-Gonzalez <inaky@linux.intel.com>

By running 'echo 1 > /sys/kernel/debug/wimax:wmxX/i2400m/trace_msg_from_user',
the driver will echo to user space all the commands being sent to the
device from user space, along with the responses.

However, this only helps with the commands being sent from user space;
with this patch, the trace hook is moved to i2400m_msg_to_dev(), which
is the single access point for running commands to the device (both by
user space and the kernel driver). This allows better debugging by
having a complete stream of commands/acks and reports.
Signed-off-by: NInaky Perez-Gonzalez <inaky@linux.intel.com>

When commands are sent from user space, trace both the command sent
and the answer received over the "echo" pipe instead of over the
"trace" pipe when command tracing is enabled. As well, when the device
sends a reports/indications, send it over the "echo" pipe.

The "trace" pipe is used by the device to send firmware traces;
gets confusing. Another named pipe makes it easier to split debug
information.
Signed-off-by: NInaky Perez-Gonzalez <inaky@linux.intel.com>

The WiMAX i2400m driver needs to generate a fake source MAC address to
fake an ethernet header (for destination, the card's MAC is
used). This is the source of the packet, which is the basestation it
came from. The basestation's mac address is not usable for this, as it
uses its own namespace and it is not always available.

Currently the fake source MAC address was being set to all zeros,
which was causing trouble with bridging.

Use random_ether_addr() to generate a proper one that creates no
trouble.
Signed-off-by: NInaky Perez-Gonzalez <inaky@linux.intel.com>

First of all, it exposes the SKB list implementation.

Second of all it's not needed.  If we get called here, we
successfully enqueued the URB with the linked SKB and
such a completion only gets called one time on such an
SKB.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This eliminates explicit references to the SKB list handling
implementation.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This code uses alloc_skb() which clears them out for us.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use struct net_device_stats provided in struct net_device instead of
private ones.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch removes the not-that-useful message in the
r6040_timer which prints the PHY status. Instead
replace it with a call to mii_check_media which will
update the link status and print it on startup.
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes a build warning due to an unused label.
Signed-off-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use MII_BUS_ID_SIZE instead.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The r8169 driver supports 3 different families of network chips
(RTL8169, RTL8168 and RTL8101). When an unknown version is found, the
driver currently always defaults to the RTL8169 variant. This has very
little chance to ever work for chips of the other families. So better
define a per-family default.
Signed-off-by: NJean Delvare <jdelvare@suse.de>
Acked-by: NFrancois Romieu <romieu@fr.zoreil.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Inspired by the patch for 8139too (bda6a15a).

Currently we can't set mac address on a running ucc_geth device.
But this is needed when you use this device as a bonding slave in
bonding device in balance-alb mode. So add this feature for ucc_geth
device.
Signed-off-by: NKevin Hao <kexin.hao@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch is for supporting C10NEM. C10NEM is a switch module, which
has back-to-back XAUI link connected to blades.
Signed-off-by: NTanli Chang <tanli.chang@sun.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If we loaded the driver with out a SFP module plugged in it would
leave it in a state that make it later unable to link when a module
was plugged in.  This patch corrects that by:

ixgbe_probe() - moving the check for IXGBE_ERR_SFP_NOT_PRESENT from
after get_invariants() to after reset_hw() as now reset_hw() is
where this condition will be indentified.

ixgbe_reset_hw_82598() - Enable this function to now return
IXGBE_ERR_SFP_NOT_PRESENT.

ixgbe_identify_sfp_module_generic() - This where the lack of SFP
module is detected.  Modifications are added to allow a different
return value for modules that just haven't been plugged in yet.

Other functions were updated to allow correct logging.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Device ID 0x10d8 is the default silicon device ID for 82599.  However, the
device will not be functional without an EEPROM, so we want to prevent the
driver from loading on the device.  Otherwise, the driver will load, but no
PHY setup or PCIe setup will occur, causing the device to be unusable.  To
prevent users from encountering this, just remove the device ID.
Signed-off-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The phy port status register has the MDI-X status bit on bit 11, not bit 3
as is currently setup in the define.  This patch corrects that so the
correct bit is checked on igp PHY types.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Acked-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Based on previous patch from Jesper Dangaard Brouer.

The RNBC (Receive No Buffers Count) register for the 82576, indicate
that frames were received when there were no available buffers in host
memory to store those frames (receive descriptor head and tail
pointers were equal).  The packet is still received by the NIC if
there is space in the FIFO on the NIC.

As the RNBC value is not a packet drop, the driver stores this value
in net_stats.rx_fifo_errors to indicate that there were no system
buffers available for the incoming packet.  Actual dropped packets
are counted in the MPC value.

Saving the stats in dev->net_stats makes it visible via
/proc/net/dev as "fifo", and thus viewable to ifconfig
as "overruns" and 'netstat -i' as "RX-OVR".

The Receive No Buffers Count (RNBC) can already be queried by
ethtool -S as "rx_no_buffer_count".
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Jesper Dangaard Brouer <hawk@comx.dk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Based on the previous patches from Jesper Dangaard Brouer <hawk@comx.dk>

Implement reading the per queue drop stats register
RQDPC (Receive Queue Drop Packet Count).  It counts the number of
packets dropped by a queue due to lack of descriptors available.

Notice RQDPC (Receive Queue Drop Packet Count) stats only gets
incremented, if the DROP_EN bit it set (in the SRRCTL register
for that queue).  If DROP_EN bit is NOT set, then the some what
equivalent count is stored in RNBC (not per queue basis).

The RQDPC register is only 12 bit, thus the precision might
suffer due to overrun in-netween the watchdog polling interval.
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Jesper Dangaard Brouer <hawk@comx.dk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Also convert DPRINTK to pr_debug and dev_printk to dev_<foo>.
Signed-off-by: NAlexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NAlexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NAlexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Get rid of private struct net_device_stats in "struct atl1e_adapter",
and use one provided in struct net_device instead.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: NKuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: NNobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This improves readability by collecting CPU dependency code.
Signed-off-by: NYoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: NNobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix the problem that this driver not update rxdesc in sh_eth_rx.
Signed-off-by: NYoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: NNobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix the probrem that TX/RX descirptor not set physical memory.
Signed-off-by: NYoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: NNobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix the problem that may not work receive process by cache coherency issue.
Signed-off-by: NYoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: NNobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NGabriel Paubert <paubert@iram.es>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The patch makes iwmc3200wifi select CFG80211 instead of LIB80211.
This fixed module link error reported by Randy Dunlap
<randy.dunlap@oracle.com> when compiling iwmc3200wifi without
cfg80211 selected. WIRELESS_EXT is also selected by iwmc3200wifi.
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

All drivers are already converted to new net_device_ops API
and nobody uses old API anymore.
Signed-off-by: NAlexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>