In order to use the quirks2, initialized the host->quirks2.
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NKyungmin Park <Kyungmin.park@samsung.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

When use the QUIRK_NONSTANDARD_CLOCK, then never set to 0 at clock control
register.  This patch fixes this problem.
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Add suppport to get voltage from device-tree node for esdhc host,
if voltage-ranges was specified in device-tree node we can get
ocr_mask instead of read from host capacity register. If not voltages
still can be get from host capacity register.
Signed-off-by: NHaijun Zhang <haijun.zhang@freescale.com>
Acked-by: NAnton Vorontsov <anton@enomsg.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

We use host->ocr_mask to hold the voltage get from device-tree
node, In case host->ocr_mask was available, we use host->ocr_mask
as the final available voltage can be used by MMC/SD/SDIO card.
Signed-off-by: NHaijun Zhang <haijun.zhang@freescale.com>
Reviewed-by: NAnton Vorontsov <anton@enomsg.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

OMAP's hs_mmc driver is used for MMC controller operation on many
omap2plus SoCs (OMAP2430, OMAP3, 4, 5 and AM335x).

Considering that the device tree entries are already present for these,
allow the driver to be built using the config ARCH_OMAP2PLUS rather
than individually adding a config for each SoC to enable the
support.

Use COMPILE_TEST to enable the build for other platforms.
Signed-off-by: NAmarinder Bindra <a-bindra@ti.com>
Cc: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Cc: Nishanth Menon <nm@ti.com>
Acked-by: NFelipe Balbi <balbi@ti.com>
Acked-by: NBalaji T K <balajitk@ti.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Commit 1f6b9fa4 consolidated writes to
the STAT register in one location, moving them from omap_hsmmc_do_irq()
to omap_hsmmc_irq(). This move has the unwanted side effect that the
controller status flags are potentially cleared after a new command has
been started as a consequence of reading the previous status flags.
This means that if the new command changes the status flags before the
IRQ routine returns, those flags may be cleared without handling the
event which asserted them, and thus missing the event.
Move the writing of the STAT register back in omap_hsmmc_do_irq(),
before handling the status flags which generated the interrupt.
Signed-off-by: NFrancesco Lavra <francescolavra.fl@gmail.com>
Reviewed-and-Tested-by: NBalaji T K <balajitk@ti.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

The Exynos5420 has a DWMMC controller which is different from prior
versions.This patch adds a new compatible string for Exynos5420.
Signed-off-by: NAbhilash Kesavan <a.kesavan@samsung.com>
Reviewed-by: NAlim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: NYuvaraj Kumar C D <yuvaraj.cd@samsung.com>
Acked-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Some newer MMCIF IP revisions contain a CE_CLK_CTRL2 register, that has to
be set for proper operation. Support for this feature is added in a way to
preserve the current behaviour by default, i.e. when it is not enabled
in platform data. Patch is based on work by Nobuyuki HIRAI.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Some earlier MMCIF IP revisions contained Command Completion Signal
support, which has been dropped again in modern versions. Sopport for
this feature is added in a way to preserve the current behaviour by
default, i.e. when it is not enabled in platform data. Patch is based
on work by Nobuyuki HIRAI.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

To use DMA in the Device Tree case the driver has to be modified
to use suitable API to obtain DMA channels.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

sh_dma.h isn't needed in sh_mmcif.h, move it into sh_mmcif.c.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Add further OF compatibility strings to the SDHI driver to be able to
precisely control driver's behaviour on each of them.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Acked-by: NMagnus Damm <damm@opensource.se>
Acked-by: NSimon Horman <horms@verge.net.au>
Signed-off-by: NChris Ball <cjb@laptop.org>

This patch enables bus-mastering mode for MMC controller to allow IDMAC
transfers.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: NSeungwon Jeon <tgih.jun@samsung.com>
Tested-by: NPrabu Thangamuthu <Prabu.T@synopsys.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

There is a typo when the mapped space is from BAR 2, but BAR 0 is
used instead.  This patch fixes the typo.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: NPrabu Thangamuthu <Prabu.T@synopsys.com>
Acked-by: NSeungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

The .set_pwr() callback isn't used anymore as all platforms register
GPIO-controlled regulators. Remove it.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

All platforms pass the CD GPIO number to the driver in the .cd_gpio
field. The .get_cd() callback isn't used anymore, remove it
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

The .set_pwr() callback isn't used anymore as all platforms register
GPIO-controlled regulators. Remove it.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

All platforms pass the CD GPIO number to the driver in the .cd_gpio
field. The .get_cd() callback isn't used anymore, remove it.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

The .set_pwr() callback isn't used anymore as all platforms register
GPIO-controlled regulators. Remove it.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

All platforms now pass the CD and RO GPIOs to the MMC SPI driver, those
callbacks are not used anymore. Remove them.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Add support for passing CD/RO GPIO numbers directly to the mmc_spi
driver instead of relying solely on board code callbacks to retrieve the
CD/RO signals values. The driver will enable debouncing on the card
detect GPIO if the cd_debounce field is set to a non-zero value.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Add a debounce parameter to the mmc_gpio_request_cd() function that
enables GPIO debouncing when set to a non-zero value. This can be used
by MMC host drivers to enable debouncing on the card detect signal.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Include 'dw_mmc-pltfm.h' header file in order to fix the following
sparse warnings:

drivers/mmc/host/dw_mmc-pltfm.c:36:5: warning: symbol 'dw_mci_pltfm_register' was not declared. Should it be static?
drivers/mmc/host/dw_mmc-pltfm.c:94:1: warning: symbol 'dw_mci_pltfm_pmops' was not declared. Should it be static?
drivers/mmc/host/dw_mmc-pltfm.c:118:5: warning: symbol 'dw_mci_pltfm_remove' was not declared. Should it be static?
Suggested-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Acked-by: NSeungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

I'm testing SH-Mobile SDHI driver in DMA mode with  a new DMA controller  using
'bonnie++' and getting DMA error after which the tmio_mmc_dma.c code falls back
to PIO but all commands time out after that.  It turned out that the fallback
code calls tmio_mmc_enable_dma() with RX/TX channels already freed and pointers
to them cleared, so that the function bails out early instead  of clearing the
DMA bit in the CTL_DMA_ENABLE register. The regression was introduced by commit
162f43e3 (mmc: tmio: fix a deadlock).
Moving tmio_mmc_enable_dma() calls to the top of the PIO fallback code in
tmio_mmc_start_dma_{rx|tx}() helps.
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: stable@vger.kernel.org # 3.1+
Signed-off-by: NChris Ball <cjb@laptop.org>

Added missing MFD_SYSCON dependency for SOCFPGA in order to fix
the following link error.

drivers/mmc/host/dw_mmc-socfpga.c:49: undefined reference to `syscon_regmap_lookup_by_compatible'
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Acked-by: NJaehoon Chung <jh80.chung@samsung.com>
Acked-by: NSeungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Replace clk_enable/disable with clk_prepare_enable/disable_unprepare to
avoid common clk framework warnings.
Signed-off-by: NBoris BREZILLON <b.brezillon@overkiz.com>
Acked-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Signed-off-by: NWei WANG <wei_wang@realsil.com.cn>
Signed-off-by: NChris Ball <cjb@laptop.org>

omap_hsmmc.c depends on <linux/sizes.h> being included indirectly by
another header. Once we enable COMPILE_TEST for this driver, we might
compile under architectures which won't include <linux/sizes.h> for us.
In fact, one such case is x86.

In order to prevent compile breakages, let's explicitly include
<linux/sizes.h>.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Acked-by: NBalaji T K <balajitk@ti.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

In (1fb5f68a mmc: dw_mmc: Don't loop when handling an interrupt), the
code for handling DW_MCI_QUIRK_IDMAC_DTO became dead code.  Move it to
where it ought to live.

Found by code inspection and compile-tested only--I don't know of any
boards that need DW_MCI_QUIRK_IDMAC_DTO.
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Acked-by: NSeungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Generally request_irq() should be called after hardware has been
initialized into a sane state.  However, sdhci driver currently calls
request_irq() before sdhci_init().  At least, the following kernel panic
seen on i.MX6 is caused by that.  The sdhci controller on i.MX6 may have
noisy glitch on DAT1 line, which will trigger SDIO interrupt handling
once request_irq() is called.  But at this point, the SDIO interrupt
handler host->sdio_irq_thread has not been registered yet.  Thus, we
see the NULL pointer access with wake_up_process(host->sdio_irq_thread)
in mmc_signal_sdio_irq().

Fix the panic by simply reverse the calling sequence between
request_irq() and sdhci_init().

sdhci-pltfm: SDHCI platform and OF driver helper
mmc0: no vqmmc regulator found
mmc0: no vmmc regulator found
Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = 80004000
[00000000] *pgd=00000000
Internal error: Oops: 5 [#1] SMP ARM
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.10.0+ #3
task: 9f860000 ti: 9f862000 task.ti: 9f862000
PC is at wake_up_process+0xc/0x44
LR is at sdhci_irq+0x378/0x93c
pc : [<8004f768>]    lr : [<803fb698>]    psr: 40000193
sp : 9f863ba0  ip : 9f863bb8  fp : 9f863bb4
r10: 9f807900  r9 : 80761fbc  r8 : 00000000
r7 : 00000000  r6 : 00000000  r5 : 00000001  r4 : 9fa68000
r3 : 00000001  r2 : 00000002  r1 : 20000193  r0 : 00000000
Flags: nZcv  IRQs off  FIQs on  Mode SVC_32  ISA ARM  Segment kernel
Control: 10c53c7d  Table: 8000404a  DAC: 00000017
Process swapper/0 (pid: 1, stack limit = 0x9f862238)
Stack: (0x9f863ba0 to 0x9f864000)
3ba0: 00000001 9fa68000 9f863c04 9f863bb8 803fb698 8004f768 8011af00 80265aac
3bc0: 00000000 000003d9 00000000 9fa51880 00000001 00000000 9f863c14 9fa53640
3be0: 00000001 00000000 00000000 00000036 80761fbc 9f807900 9f863c3c 9f863c08
3c00: 80075154 803fb32c 802c2b38 802c63d8 802c63cc 9f807900 00000001 9f862000
3c20: 00000036 00000000 9f807930 60000113 9f863c54 9f863c40 800752ec 8007510c
3c40: 9f807900 00000001 9f863c6c 9f863c58 80078324 800752a8 00000036 8071fd64
3c60: 9f863c84 9f863c70 80074ac0 80078294 00000140 8072ab78 9f863cac 9f863c88
3c80: 8000ee34 80074aa4 00000000 a080e10c 8072acbc 9f863cd0 a080e100 00000036
3ca0: 9f863ccc 9f863cb0 80008600 8000edec 805386a8 60000113 ffffffff 9f863d04
3cc0: 9f863d24 9f863cd0 8000e0c0 800085dc 9f807950 60000113 00000007 00000000
3ce0: 9f807900 9fa53640 9f807950 9fa68240 00000036 9f807930 60000113 9f863d24
3d00: 9f863d28 9f863d18 80076834 805386a8 60000113 ffffffff 9f863d64 9f863d28
3d20: 80076834 80538688 00000000 800bfe4c 00002fac 00000001 9f863d54 9fa53640
3d40: 9f807900 803fb320 9fa68240 00000080 00000000 00000036 9f863d94 9f863d68
3d60: 80076b38 80076674 00000080 9fa68240 9fa68000 04000000 9fa6836c 9fa68380
3d80: 806d620c 80700350 9f863dc4 9f863d98 803fce8c 80076a88 9fa532c0 9fa68240
3da0: 9fa51490 9fa51490 9fa68240 00000000 9f8ae600 9f81d080 9f863df4 9f863dc8
3dc0: 803fea0c 803fc808 9f863de4 9f863dd8 80125850 807b1ed8 807576b8 9f8ae610
3de0: 00000000 807576b8 9f863e04 9f863df8 802ee0d4 803fe798 9f863e2c 9f863e08
3e00: 802ecd1c 802ee0c0 00000000 9f8ae610 807576b8 9f8ae644 00000000 000000a9
3e20: 9f863e4c 9f863e30 802ecec0 802ecc30 9f83355c 807576b8 802ece2c 00000000
3e40: 9f863e74 9f863e50 802eb3d8 802ece38 9f83355c 9f8ac3b4 9f833570 807576b8
3e60: 80746e70 9fa51400 9f863e84 9f863e78 802ec838 802eb388 9f863eb4 9f863e88
3e80: 802ec3d0 802ec824 80692748 807620c0 9f863eb4 807576b8 00000006 807620c0
3ea0: 00000000 000000a9 9f863edc 9f863eb8 802ed3e8 802ec2fc 9f862000 00000006
3ec0: 807620c0 00000000 000000a9 80700350 9f863eec 9f863ee0 802ee2f8 802ed374
3ee0: 9f863efc 9f863ef0 80700364 802ee2b8 9f863f54 9f863f00 8000870c 8070035c
3f00: 9f863f54 9f863f10 9f862000 00000000 00000000 00000006 00000006 806d3aa4
3f20: 00000000 80688b18 9f863f54 80713560 00000006 80713540 807620c0 000000a9
3f40: 806d620c 8071ec24 9f863f94 9f863f58 806d6994 800086dc 00000006 00000006
3f60: 806d620c f6bfffff fb7f5df7 00000000 8052da28 00000000 00000000 00000000
3f80: 00000000 00000000 9f863fac 9f863f98 8052da38 806d689c ffffffff 00000000
3fa0: 00000000 9f863fb0 8000e5d8 8052da34 00000000 00000000 00000000 00000000
3fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
3fe0: 00000000 00000000 00000000 00000000 00000013 00000000 d9cdf5ff 1fff5ffe
Backtrace:
[<8004f75c>] (wake_up_process+0x0/0x44) from [<803fb698>] (sdhci_irq+0x378/0x93c)
 r4:9fa68000 r3:00000001
[<803fb320>] (sdhci_irq+0x0/0x93c) from [<80075154>] (handle_irq_event_percpu+0x54/0x19c)
[<80075100>] (handle_irq_event_percpu+0x0/0x19c) from [<800752ec>] (handle_irq_event+0x50/0x70)
[<8007529c>] (handle_irq_event+0x0/0x70) from [<80078324>] (handle_fasteoi_irq+0x9c/0x170)
 r5:00000001 r4:9f807900
[<80078288>] (handle_fasteoi_irq+0x0/0x170) from [<80074ac0>] (generic_handle_irq+0x28/0x38)
 r5:8071fd64 r4:00000036
[<80074a98>] (generic_handle_irq+0x0/0x38) from [<8000ee34>] (handle_IRQ+0x54/0xb4)
 r4:8072ab78 r3:00000140
[<8000ede0>] (handle_IRQ+0x0/0xb4) from [<80008600>] (gic_handle_irq+0x30/0x64)
 r8:00000036 r7:a080e100 r6:9f863cd0 r5:8072acbc r4:a080e10c
r3:00000000
[<800085d0>] (gic_handle_irq+0x0/0x64) from [<8000e0c0>] (__irq_svc+0x40/0x54)
Exception stack(0x9f863cd0 to 0x9f863d18)
3cc0:                                     9f807950 60000113 00000007 00000000
3ce0: 9f807900 9fa53640 9f807950 9fa68240 00000036 9f807930 60000113 9f863d24
3d00: 9f863d28 9f863d18 80076834 805386a8 60000113 ffffffff
 r7:9f863d04 r6:ffffffff r5:60000113 r4:805386a8
[<8053867c>] (_raw_spin_unlock_irqrestore+0x0/0x30) from [<80076834>] (__setup_irq+0x1cc/0x414)
[<80076668>] (__setup_irq+0x0/0x414) from [<80076b38>] (request_threaded_irq+0xbc/0x140)
[<80076a7c>] (request_threaded_irq+0x0/0x140) from [<803fce8c>] (sdhci_add_host+0x690/0xb88)
[<803fc7fc>] (sdhci_add_host+0x0/0xb88) from [<803fea0c>] (sdhci_esdhc_imx_probe+0x280/0x4d4)
 r8:9f81d080 r7:9f8ae600 r6:00000000 r5:9fa68240 r4:9fa51490
[<803fe78c>] (sdhci_esdhc_imx_probe+0x0/0x4d4) from [<802ee0d4>] (platform_drv_probe+0x20/0x24)
 r8:807576b8 r7:00000000 r6:9f8ae610 r5:807576b8 r4:807b1ed8
[<802ee0b4>] (platform_drv_probe+0x0/0x24) from [<802ecd1c>] (driver_probe_device+0xf8/0x208)
[<802ecc24>] (driver_probe_device+0x0/0x208) from [<802ecec0>] (__driver_attach+0x94/0x98)
 r8:000000a9 r7:00000000 r6:9f8ae644 r5:807576b8 r4:9f8ae610
r3:00000000
[<802ece2c>] (__driver_attach+0x0/0x98) from [<802eb3d8>] (bus_for_each_dev+0x5c/0x90)
 r6:00000000 r5:802ece2c r4:807576b8 r3:9f83355c
[<802eb37c>] (bus_for_each_dev+0x0/0x90) from [<802ec838>] (driver_attach+0x20/0x28)
 r6:9fa51400 r5:80746e70 r4:807576b8
[<802ec818>] (driver_attach+0x0/0x28) from [<802ec3d0>] (bus_add_driver+0xe0/0x234)
[<802ec2f0>] (bus_add_driver+0x0/0x234) from [<802ed3e8>] (driver_register+0x80/0x14c)
 r8:000000a9 r7:00000000 r6:807620c0 r5:00000006 r4:807576b8
[<802ed368>] (driver_register+0x0/0x14c) from [<802ee2f8>] (platform_driver_register+0x4c/0x60)
[<802ee2ac>] (platform_driver_register+0x0/0x60) from [<80700364>] (sdhci_esdhc_imx_driver_init+0x14/0x1c)
[<80700350>] (sdhci_esdhc_imx_driver_init+0x0/0x1c) from [<8000870c>] (do_one_initcall+0x3c/0x164)
[<800086d0>] (do_one_initcall+0x0/0x164) from [<806d6994>] (kernel_init_freeable+0x104/0x1d0)
[<806d6890>] (kernel_init_freeable+0x0/0x1d0) from [<8052da38>] (kernel_init+0x10/0xec)
[<8052da28>] (kernel_init+0x0/0xec) from [<8000e5d8>] (ret_from_fork+0x14/0x3c)
 r4:00000000 r3:ffffffff
Code: e89da800 e1a0c00d e92dd818 e24cb004 (e5903000)
---[ end trace e9af3588936b63f0 ]---
Kernel panic - not syncing: Fatal exception in interrupt
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

stmp_reset_block() may fail, so let's check its return value and
propagate it in the case of error.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Acked-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

Using devm_clk_get() allows us to remove the clk_put() calls, so
let's use it to simplify the code.

Rename the 'out_clk_put' label to 'out_clk_disable' now that clk_put
is removed.
Signed-off-by: NFabio Estevam <festevam@gmail.com>
Acked-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

In case of error, the function devm_ioremap_resource() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check should
be replaced with IS_ERR(). Also there is already a error message within
devm_ioremap_resource(), so remove the dev_err call to avoid redundant
error message.
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NChris Ball <cjb@laptop.org>

'vub300_init_card' is used only in this file. Make it
static.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

'bcm2835_sdhci_get_min_clock' is used only in this file.
Make it static.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

This patch fixes a compiler warning:

drivers/mmc/host/tmio_mmc_pio.c: In function 'tmio_mmc_power_on':
drivers/mmc/host/tmio_mmc_pio.c:798:19: warning: ignoring return value of
'regulator_enable', declared with attribute warn_unused_result [-Wunused-result]
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Add SDHCI driver for the Broadcom 281xx SoCs.

Still missing:
 - power managemement
Signed-off-by: NChristian Daudt <csd@broadcom.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

Add a card_event callback to sdhci so that clients can provide their
own card_event to be called when card_detect is triggered.
Signed-off-by: NChristian Daudt <csd@broadcom.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Add another PCI device id for an eMMC host controller.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

The P2020 has a non-standard implementation of the SDHCI_HOST_CONTROL
register. This patch adds a QUIRK in the SDHCI header to signal that
a host controller has a non-standard SDHCI_HOST_CONTROL register. The
patch adds a check to the function esdhc_writeb in file
sdhci-of-esdhc.c, where it checks if the write is done to the
SDHCI_HOST_CONTROL register and th host has the above mentioned QUIRK,
then the function simply returns instead of writing to the register.
The patch also detects if the processor is P2020 (by looking in dev
tree) and if so, adds the QUIRK to the host->quirk2
Signed-off-by: NOded Gabbay <ogabbay@advaoptical.com>
Reviewed-by: NAnton Vorontsov <anton@enomsg.org>
Signed-off-by: NChris Ball <cjb@laptop.org>