intel_update_max_cdclk() doesn't have a switch case for Broxton, so
dev_priv->max_cdclk_freq gets set to whatever clock frequency we're
currently running at (e.g., 144 MHz) rather than the true maximum.  This
causes our max dotclock to also be set too low and in turn leads mode
verification to reject perfectly valid modes while loading EDID firmware
blobs.

Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459892239-14041-1-git-send-email-matthew.d.roper@intel.com

Extract the GPLL reference frequency from CCK and use it in the
GPU freq<->opcode conversions on VLV/CHV. This eliminates all the
assumptions we have about which divider is used for which czclk
frequency.

Note that unlike most clocks from CCK, the GPLL ref clock is a divided
down version of the CZ clock rather than the HPLL clock. CZ clock itself
is a divided down version of the HPLL clock though, so in effect it just
gets divided down twice.

While at it, throw in a few comments explaining the remaining constants
for anyone who later wants to compare this to the spreadsheets.

v2: Add slow/fast notes for CHV clocks (Imre)
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1457120584-26080-2-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com> (v1)

Deal with errors from drm_universal_plane_init() in primary and cursor
plane init paths (sprites were already covered). Also make the code
neater by using goto for error handling.

v2: Rebased due to drm_universal_plane_init() 'name' parameter
v3: Another rebase due to s/""/NULL/
v4: Rebased on drm-nightly (Matthew Auld)
v5: Fix email address (Matthew Auld)
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NMatthew Auld <matthew.auld@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458571402-32749-1-git-send-email-matthew.auld@intel.com

VLV DPLL is somewhat sane and doesn't run on luck.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458052809-23426-7-git-send-email-ville.syrjala@linux.intel.comAcked-by: NJani Nikula <jani.nikula@intel.com>

Supposedly the power sequencer still locks out the DPLL registers on
CHV, so let's issue a warning if it's still locked when enabling the
DPLL.

Also drop the redundant IS_MOBILE() check for VLV when we check the same
thing.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458052809-23426-6-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NJani Nikula <jani.nikula@intel.com>

Avoid redundant crtc->pipe lookups by giving vlv_enable_pll() a local
pipe variable. Also makes it look more like the corresponding CHV code.

While at is change the CHV code to enum pipe from int,
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458052809-23426-5-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NJani Nikula <jani.nikula@intel.com>

DPLL_MD(PIPE_C) is AWOL on CHV. Instead of fixing it someone added
chicken bits to propagate the pixel multiplier from DPLL_MD(PIPE_B)
to either pipe B or C. So do that to make pixel repeat work on pipes
B and C. Pipe A is fine without any tricks.

Fortunately the pixel repeat propagation appears to be a oneshot
operation, so once the value has been written we can clear the
chicken bits. So it is still possible to drive pipe B and C with
different pixel multipliers simultaneosly.

Looks like DPLL_VGA_MODE_DIS must also be set in DPLL(PIPE_B)
for this to work. But since we keep that bit always set in all
DPLLs there's no problem.

This of course means we can't reliably read out the pixel multiplier
for pipes B and C. That would make the state checker unhappy, so I
added shadow copies of those registers in to dev_priv. The other
option would have been to skip pixel multiplier, dpll_md an dotclock
checks entirely on CHV, but that feels like a serious loss of cross
checking, so just pretending that we have working DPLL MD registers
seemed better. Obviously with the shadow copies we can't detect if
the pixel multiplier was properly configured, nor can we take over
its state from the BIOS, but hopefully people won't have displays
that would be limitd to such crappy modes.

There is one strange flicker still remaining. It's visible on
pipe C/HDMID when HDMIB is enabled while driven by pipe B.
It doesn't occur if pipe A drives HDMIB, nor is there any glitch
on pipe B/HDMIB when port C/HDMID starts up. I don't have a board
with HDMIC so not sure if it happens there too. So I'm not sure
if it's somehow tied in with this strange linkage between pipe B
and C. Sadly I was unable to find an enable sequence that would
avoid the glitch, but at least it's not fatal ie. the output
recovers afterwards.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458052809-23426-4-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NJani Nikula <jani.nikula@intel.com>

The VLV and CHV DPLL disable and update are almost identical in
how the DPLL/DPLL_MD registers need to be set up. But the code
looks more different than it really is. Try to bring them into
line.

Note that we now leave the refclock always enabled for both
DPLLs in the dual channel PHY. But that's perfectly fine since
it's the same clock, and we anyway already do that when turning
the disp2d power well on.

v2: s/chv_update_pll/chv_compute_dpll/
v3: Add a note that we leave refclocks enabled for both DPLLs (Jani)
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458052809-23426-3-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NJani Nikula <jani.nikula@intel.com>

These BUGs don't serve any purpose IMO. Throw them out.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458052809-23426-2-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NJani Nikula <jani.nikula@intel.com>

Refer to the GGTT VM consistently as "ggtt->base" instead of just "ggtt",
"vm" or indirectly through other variables like "dev_priv->ggtt.base"
to avoid confusion with the i915_ggtt object itself and PPGTT VMs.

Refer to the GGTT as "ggtt" instead of indirectly through chaining.

As a bonus gets rid of the long-standing i915_obj_to_ggtt vs.
i915_gem_obj_to_ggtt conflict, due to removal of i915_obj_to_ggtt!

v2:
- Added some more after grepping sources with Chris

v3:
- Refer to GGTT VM through ggtt->base consistently instead of ggtt_vm
  (Chris)

v4:
- Convert all dev_priv->ggtt->foo accesses to ggtt->foo.

v5:
- Make patch checker happy

Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>

Without this a vblank may occur between updating color management
and planes, which should be prevented.

intel_color_set_csc was called in update pipe config because the
handover from hardware may not have any csc set, which resulted
in a black screen. Because of this also update color management
during fastset.
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Tested-by: NLionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: NLionel Landwerlin <lionel.g.landwerlin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459350996-4957-4-git-send-email-maarten.lankhorst@linux.intel.com
[mlankhorst: Remove comment in response to review feedback.]

Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: NLionel Landwerlin <lionel.g.landwerlin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459350996-4957-2-git-send-email-maarten.lankhorst@linux.intel.com

And move the comment to the right macro. This was mixed up in

commit cfb23ed6
Author: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Date:   Tue Jul 14 12:17:40 2015 +0200

    drm/i915: Allow fuzzy matching in pipe_config_compare, v2

v2: Rebase.

Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Daniel Stone <daniels@collabora.com>
Acked-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459330476-32453-1-git-send-email-daniel.vetter@ffwll.ch

Currently the machine hangs during booting while accessing the
BXT_MIPI_PORT_CTRL register during pipe HW state readout. After some
experimentation I found that the hang is caused by the DSI PLL being
disabled, or it being enabled but with an incorrect divider
configuration. Enabling the PLL got rid of the boot problem, so fix
this by checking the PLL enabled state/configuration before attempting
to read out the HW state.

The DSI_PLL_ENABLE register is in the always-on power well, while the
BXT_DSI_PLL_CTL is in power well 0. This isn't exactly matched by the
transcoder power domain, but what we really need is just a runtime PM
reference, which is provided by any power domain.

Ville also found this dependency specified in BSpec, so I added a
reference to that too.

v2:
- Make sure we hold a power reference while accessing the PLL registers.
v3: (Jani)
- Simplify check in bxt_get_dsi_transcoder_state()
- Add comment explaining why we check for valid dividers in
  bxt_dsi_pll_is_enabled()

CC: Shashank Sharma <shashank.sharma@intel.com>
CC: Uma Shankar <uma.shankar@intel.com>
CC: Jani Nikula <jani.nikula@intel.com>
Fixes: c6c794a2 ("drm/i915/bxt: Initialize MIPI DSI for BXT")
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NShashank Sharma <shashank.sharma@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458816100-31269-1-git-send-email-imre.deak@intel.com

intel_post_plane_update did an extra vblank wait that's no longer needed when enabling ips.

Changes since v1:
- Add comment explaining why vblank wait is performed. (Paulo)
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/56F29B28.5070804@linux.intel.com

Split a pnv_crtc_compute_clock(), so the differences between platforms
become more obvious.

With this, there are no more users of intel_limit() or the ->find_dpll()
hook, so get rid of them.
Signed-off-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458576016-30348-16-git-send-email-ander.conselvan.de.oliveira@intel.com

Split a G4X specific version from i9xx_crtc_compute_clock(). With this
the differences between platforms become more obvious.
Signed-off-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458576016-30348-15-git-send-email-ander.conselvan.de.oliveira@intel.com

Split a GEN2 specific version from i9xx_crtc_compute_clock(). With this
there is no need for i9xx_get_refclk() anymore, and the differences
between platforms become more obvious.

v2: Use i8xx as prefix instead of gen2. (Ville and Daniel)
Signed-off-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458653723-17951-1-git-send-email-ander.conselvan.de.oliveira@intel.com

In order for VLV and CHV to use i9xx_crtc_compute_clocks(), a number
of if ladders is necessary: one for setting the find_dpll() hook, one
for choosing the limits struct, one for choosing the right compute dpll
function and one for initializing the crtc_compute_clock() hook.

By extracting a platform specific implementation for each platform, the
number of if-ladders is reduced to one.

While at it also clean up bxt_find_best_dpll() which depends on some of
the CHV code.
Signed-off-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458576016-30348-13-git-send-email-ander.conselvan.de.oliveira@intel.com

Merge ironlake_compute_clocks() into ironlake_crtc_compute_clock() so
the clock computation logic is all in one place. The resulting function
is still quite simple. Follow up patches will make the similar code for
GMCH platforms look similar.
Signed-off-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458576016-30348-12-git-send-email-ander.conselvan.de.oliveira@intel.com

Follow what is done in i8xx_compute_dpll() and i9xx_compute_dpll() and
move the lower level details of setting crtc_state->dpll_hw_state into
the _compute_dpll() function.
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458576016-30348-11-git-send-email-ander.conselvan.de.oliveira@intel.com

When calculating clocks, just pass a pointer to crtc_state->dpll
directly to the find_dpll() hook. Back when this was introduced in
commit f47709a9 ("drm/i915: create pipe_config->dpll for clock
state") there was no staged crtc config or atomic crtc state, so it was
possible to overwrite the current configuration on error. That hasn't
been the case for a while now, so finally make it "disappear".
Signed-off-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458576016-30348-10-git-send-email-ander.conselvan.de.oliveira@intel.com

None of the code in ironlake_crtc_compute_clock() is relevant for CPU
eDP. The CPU eDP PLL is turned on and off in ironlake_edp_pll_{on,off}
from the DP code and that doesn't depend on the crtc_state->dpll values,
so just return early in that case.

v2: Rebase without patch that drops lvds downclock code. (Ville)
Signed-off-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458576016-30348-9-git-send-email-ander.conselvan.de.oliveira@intel.com

The checks were added in commit 5dc5298b ("drm/i915: add proper
CPU/PCH checks to crtc_mode_set functions") in a time when there was
doubts on what PCHs would be supported by HSW. There are similar checks
for PCH type in intel_detect_pch() and the function pointers are
initialized based on platform/pch information, so the removed WARN can't
ever be reached.

v2: Rebase without patch that drops lvds downclock code. (Ville)
Signed-off-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458576016-30348-8-git-send-email-ander.conselvan.de.oliveira@intel.com

Remove the clock calculation from ironlake_crtc_compute_clock() when the
encoder compute_config() already set one. The value was just thrown away
in that case.

Note that the previously set clock is not validated against the limits
anymore. That is ok since the fixed clocks from DP and SDVO are within
the supported range, so the call to ironlake_compute_clocks() would
never fail in that case.

v2: Add note about not checking fixed clocks agains limits. (Maarten)
Signed-off-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458576016-30348-7-git-send-email-ander.conselvan.de.oliveira@intel.com

Check has_reduced_clock only once when setting dpll_hw_state, making the
code slightly more readable.
Signed-off-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458576016-30348-6-git-send-email-ander.conselvan.de.oliveira@intel.com

The call to dev_priv->display.find_dpll() is already in platform
specific code, so avoid the extra detour.
Signed-off-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458576016-30348-5-git-send-email-ander.conselvan.de.oliveira@intel.com

The function intel_ironlake_limit() is only called by the crtc compute
clock path. By merging it into ironlake_compute_clocks(), the code gets
clearer, since there's no more if-ladders to follow.
Signed-off-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458576016-30348-4-git-send-email-ander.conselvan.de.oliveira@intel.com

A previous patch made ironlake_get_refclk() very simple, so merge
it into its only caller.
Signed-off-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458576016-30348-3-git-send-email-ander.conselvan.de.oliveira@intel.com

LVDS is not cloneable, so the check is unnecessary. Removing it makes
the code neater.

v2: Remove checks from GMCH code too, not only ILK+. (Ville)
Signed-off-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458576016-30348-2-git-send-email-ander.conselvan.de.oliveira@intel.com

The wait for other gens was added in commit 564ed191 ("drm/i915:
gmch: fix stuck primary plane due to memory self-refresh mode") since
that's necessary when disabling cxsr. However, cxsr disabling was later
moved to intel_pre_disable_primary() in commit 87d4300a ("drm/i915:
Move intel_(pre_disable/post_enable)_primary to intel_display.c, and use
it there.") and that function got its own vblank wait for cxsr in commit
262cd2e1 ("drm/i915: CHV DDR DVFS support and another watermark
rewrite"). So remove the extra vblank wait from i9xx_crtc_distable().

Cc: Kalyan Kondapally <kalyan.kondapally@intel.com>
Signed-off-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1458634284-6080-1-git-send-email-ander.conselvan.de.oliveira@intel.com

This patch contains following changes:
1. Add BXT MIPI display address base.
2. Call dsi_init from display_setup function.

v2: Rebased on latest nightly branch

v3 by Jani: init dsi after ddi
Signed-off-by: NShashank Sharma <shashank.sharma@intel.com>
Signed-off-by: NUma Shankar <uma.shankar@intel.com>
Acked-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458640910-5338-1-git-send-email-jani.nikula@intel.com

At the end of an atomic commit, we currently wait for vblanks to
complete, call put() on the various runtime PM references, and then try
to optimize our watermarks (on platforms that need two-step watermark
programming).  This can lead to watermark registers being programmed
while the power well is powered down.  We need to wait until after
watermark optimization is complete before dropping our runtime power
references.

Note that in the future the watermark optimization is probably going to
move to an asynchronous workqueue task that happens at some arbitrary
point after vblank.  When we make that change, we'll no longer
necessarily be operating under the power reference held here, so we'll
need to wrap the watermark register programmin in a call to
intel_runtime_pm_get_if_in_use() or similar.

Cc: arun.siluvery@linux.intel.com
Cc: ville.syrjala@linux.intel.com
Cc: maarten.lankhorst@linux.intel.com
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=94349
Fixes: ed4a6a7c ("drm/i915: Add two-stage ILK-style watermark programming (v11)")
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1457135979-23727-1-git-send-email-matthew.d.roper@intel.com

Patch based on a previous series by Shashank Sharma.

v2: Do not read GAMMA_MODE register to figure what mode we're in

v3: Program PREC_PAL_GC_MAX to clamp pixel values > 1.0

    Add documentation on how the Broadcast RGB property is affected by CTM

v4: Update contributors

v5: Refactor degamma/gamma LUTs load into a single function

v6: Fix missing intel_crtc variable (bisect issue)

v7: Fix & simplify limited range matrix multiplication (Matt Roper's
    comment)
Signed-off-by: NShashank Sharma <shashank.sharma@intel.com>
Signed-off-by: NKumar, Kiran S <kiran.s.kumar@intel.com>
Signed-off-by: NKausal Malladi <kausalmalladi@gmail.com>
Signed-off-by: NLionel Landwerlin <lionel.g.landwerlin@intel.com>
Acknowledged-by: NMatt Roper <matthew.d.roper@intel.com>
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458125837-2576-4-git-send-email-lionel.g.landwerlin@intel.com

Implement Daniel Stone's recommendation to not read registers to infer
the hardware's state.

v2: Read GAMMA_MODE register value at init (Matt Roper's comment)

v3: Read GAMMA_MODE register in intel_modeset_readout_hw_state along
    with other registers (Matt Roper's comment).

v4: Mask GAMMA_MODE register with interesting bits when reading
Signed-off-by: NLionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: NMatt Roper <matthew.d.roper@intel.com>
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458125837-2576-3-git-send-email-lionel.g.landwerlin@intel.com

The moves a couple of functions programming the gamma LUT and CSC
units into their own file.

On generations prior to Haswell there is only a gamma LUT. From
haswell on there is also a new enhanced color correction unit that
isn't used yet. This is why we need to set the GAMMA_MODE register,
either we're using the legacy 8bits LUT or enhanced LUTs (of 10 or
12bits).

The CSC unit is only available from Haswell on.

We also need to make a special case for CherryView which is recognized
as a gen 8 but doesn't have the same enhanced color correction unit
from Haswell on.

v2: Fix access to GAMMA_MODE register on older generations than
    Haswell (from Matt Roper's comments)
Signed-off-by: NLionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: NMatt Roper <matthew.d.roper@intel.com>
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1458125837-2576-2-git-send-email-lionel.g.landwerlin@intel.com

The BXT display connections have DSI transcoders A and C that can be
muxed to any pipe, not unlike the eDP transcoder. Add the notion of DSI
transcoders.

The "normal" transcoders A, B and C are not used with BXT DSI, so care
must be taken to avoid accessing those registers with DSI transcoders in
the hardware state readout, modeset, and generally everywhere.

v2: addressing comments by Ville:
 - rename the dsi get config function to hsw_get_dsi_transcoder_state
 - rebase onto the higher level split of pipe/transcoder functions
 - use more has_dsi_encoder as we can now because of the above,
   with no need to look at the transcoder so much
 - rename IS_DSI_TRANSCODER to transcoder_is_dsi
 - use the above a bit more instead of comparing to < TRANSCODER_EDP
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/299740536b7941e31b2744f3ce34f7afe936a771.1458313400.git.jani.nikula@intel.com

Makes it neater to add the same for DSI transcoder. No functional
changes.

v2: rename to hsw_get_transcoder_state and add a comment about grabbing
    power reference (Ville)
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/c473a73d69dcd61584419d85ff7908a8717b0594.1458313400.git.jani.nikula@intel.com

Prep work for DSI transcoders. No functional changes.

v2: call split functions at a higher level (Ville)
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/981252d5d5f82d009d73e1b2ae93d9ab7bee8de8.1458313400.git.jani.nikula@intel.com

Prep work for DSI transcoders. No functional changes.

v2: call split functions at a higher level (Ville)
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/8d67a05eb869a7b0c4ee17c2d3b0b029de34851c.1458313400.git.jani.nikula@intel.com