As of commit 9a1091ef ("irqchip: gic: Support hierarchy irq
domain."), the Lager legacy board support is known to be broken.

The IRQ numbers of the GIC are now virtual, and no longer match the
hardcoded hardware IRQ numbers in the legacy platform board code.

To fix this issue specific to non-multiplatform r8a7790 and Lager:
 1) Instantiate the GIC from platform board code and also
 2) Skip over the DT arch timer as well as
 3) Force delay setup based on DT CPU frequency

With these 3 fixes in place interrupts on Lager are now unbroken.

Partially based on legacy GIC fix by Geert Uytterhoeven, thanks to
him for the initial work.
Signed-off-by: NMagnus Damm <damm+renesas@opensource.se>
Acked-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Platform data support has been removed from the DU driver, drop DU
support from the legacy Lager board file. The multiplatform DT-based
Lager support should be used instead.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NSimon Horman <horms+renesas@verge.net.au>
Signed-off-by: NDave Airlie <airlied@redhat.com>

The information is already included in the COPYING file in the kernel
sources root directory, we don't want to modify all source files when
the FSF will move to a new address, and I'm tired of seeing the related
checkpatch.pl warnings.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

In preparation for DT support where panel timings will be described by a
DRM-agnostic video mode, replace the struct drm_mode_modeinfo instance
in the panel platform data with a struct videomode.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>

sh_mobile_sdhi cares multiblock read bug.
remove MMC_CAP2_NO_MULTI_READ flag from board code
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: NSimon Horman <horms+renesas@verge.net.au>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

A number of board files in arch/arm and arch/unicore32
explicitly reference platform_bus device as a parent
for new platform devices.

This is unnecessary, as platform device API guarantees
that devices with NULL parent are going to by adopted
by the mentioned "root" device.

This patch removes or replaces with NULL such references.
Signed-off-by: NPawel Moll <pawel.moll@arm.com>
Acked-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Change location of r8a7790.h so it can be included as "r8a7790.h"
instead of the old style <mach/r8a7790.h>
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Convert the Lager board support to use shmobile_init_delay()
to be able to migrate away from per-SoC delay setup functions.
Signed-off-by: NMagnus Damm <damm+renesas@opensource.se>
Acked-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Hook in the R-Car Gen2 CMA reservation code in the board
files for Lager and Koelsch. Both the DT-reference code
and the legacy code is modified.
Signed-off-by: NMagnus Damm <damm+renesas@opensource.se>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Change location of rcar-gen2.h so it can be used as #include "rcar-gen2.h"
instead of the old style #include <mach/rcar-gen2.h>. Also clean up
the r8a7790 case to follow the same style as r8a7791.
Signed-off-by: NMagnus Damm <damm+renesas@opensource.se>
Acked-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Change location for common.h so it can be used as #include "common.h"
instead of the old style #include <mach/common.h>.
Signed-off-by: NMagnus Damm <damm+renesas@opensource.se>
Acked-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Move most of irqs.h so it can be used as #include "irqs.h"
instead of the old style #include <mach/irqs.h>.

Legacy code in drivers/pinctrl needs more work to get rid
of the "mach" portion of the include path, so some part
is left in the original location.
Signed-off-by: NMagnus Damm <damm+renesas@opensource.se>
Acked-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Acked-by: NArnd Bergmann <arnd@arndb.de>
[horms+renesas@verge.net.au: Do not add trailing blank line to irqs.h]
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Acked-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Now, R-Car sound driver supports dai info settings.
switch to use it
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

e1508289
(ASoC: rcar: fixup SND_SOC_DAIFMT_CBx_CFx flags)
corrected SND_SOC_DAIFMT_CBx_CFx definition.
But then, Lager board was maintenanced other branch.
This patch correct SND_SOC_DAIFMT_CBx_CFx flag for lager
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Ether MAC is a DMA-capable device and so should have 'dev.dma_mask' and
'dev.coherent_dma_mask' fields set properly, to reflect 32-bit DMA addressing
ability.

Currently, the code works without DMA masks but as we would have to enable
CONFIG_HIGHMEM to access the full board memory in the future, when support for
NETIF_F_SG would be added to the 'sh_eth' driver as well, the correct DMA masks
should start to matter...
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

This adds internal PCI USB host devices to R-Car H2 Lager board.
Signed-off-by: NValentine Barshak <valentine.barshak@cogentembedded.com>
[damm@opensource.se: Rebased and reworked to only include USB1 and USB2]
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Signed-off-by: NGeert Uytterhoeven <geert+renesas@linux-m68k.org>
Acked-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

SDHI0 (CN8) needs JP/SW settings
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Signed-off-by: NGeert Uytterhoeven <geert+renesas@linux-m68k.org>
Acked-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

This patch adds sound support for Lager board.
But, it is using PIO transfer at this point.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
[horms+renesas@verge.net.au: resolved conflicts]
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Add Lager board code to check the PWEN GPIO signal and refuse to
allow probe of the USBHS driver in case of DIP misconfiguration.

For correct operation Lager DIP switches SW5 and SW6 shall be
configured in 2-3 position to enable USB Function support.

If the DIP switch is configured incorrectly then the user can
simply adjust the hardware and either reboot or use the bind interface
to try to probe again:

# echo renesas_usbhs > /sys/bus/platform/drivers/renesas_usbhs/bind
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Pass Ether's PHY IRQ (which is IRQC's IRQ0) to the 'sh_eth' driver. Set the IRQ
trigger type to be low-level as per the Micrel PHY driver's setup.
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: NMagnus Damm <magnus.damm@gmail.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Remove ifdefs to make the Lager USBHS device always present.
This makes it more like other devices, no need to be special.

Also, these ifdefs by themselves do not hurt much, but combined
with USB Host device ifdefs that were proposed earlier we could
basically end up with a kernel that drives VBUS incorrectly
depending on the kernel configuration - lets not do that.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

This adds USBHS PHY and registers USBHS device if the driver is enabled.
Signed-off-by: NValentine Barshak <valentine.barshak@cogentembedded.com>
Acked-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

This adds SATA support to Lager board. Only SATA1 port is available.
Signed-off-by: NValentine Barshak <valentine.barshak@cogentembedded.com>
Acked-by: NMagnus Damm <damm@opensource.se>
[horms+renesas@verge.net.au: resolved trivial conflicts]
[horms+renesas@verge.net.au: capitalised "ARM" in subject]
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Signed-off-by: NGeert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

This adds VIN1 SoC camera along with ADV7180 subdevice support to Lager.
VIN0 camera is not registered because it has ADV7612 I2C subdevice
which is not supported yet.

Changes in V2:
* made lager_add_vin_device function static.

Changes in V3:
* capitalized ARM in the subject.
Signed-off-by: NValentine Barshak <valentine.barshak@cogentembedded.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Fixed regulator is used for SDHI0/2 Vcc.
We should use da9063 driver for Vccq,
but, it doesn't have regulator support at this point.
This patch uses gpio-regulator for it as quick-hack.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

This patch enables Spansion S25FL512SAGMFIG11 chip on QSPI,
Add support for the QSPI interface on Lager.
Signed-off-by: NHiep Cao Minh <cm-hiep@jinso.co.jp>
Acked-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Hook in shmobile_init_late() on Lager V2. This enables some PM
related things like CPUIdle and Suspend-to-RAM.

With this patch applied it is possible to use Suspend-to-RAM:
# echo enabled > /sys/class/tty/ttySC6/power/wakeup
# echo mem > /sys/power/state
(wake by sending a character on the serial console)
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Enable wakeup for the GPIO keys on the Lager board.
Signed-off-by: NShinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

In R-Car GPIO hardware block, 'chattering removal' feature can be
enabled on GPIO-n-[3:0] pins, but it's not supported on rest of pins
GPIO-n-[31:4].

Set an appropriate debounce interval, instead.  We could confirm that
spurious/unnecessary GPIO interrupts are prevented by this settings.
Signed-off-by: NShinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
Acked-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Do not build the phy fixup unless CONFIG_PHYLIB is enabled.

Other than not being useful it is also not possible to link
the code under this condition as phy_register_fixup_for_id(),
mdiobus_read() and mdiobus_write() are absent.

arch/arm/mach-shmobile/built-in.o: In function `lager_ksz8041_fixup':
board-lager.c:(.text+0xb8): undefined reference to `mdiobus_read'
board-lager.c:(.text+0xd4): undefined reference to `mdiobus_write'
arch/arm/mach-shmobile/built-in.o: In function `lager_init':
board-lager.c:(.init.text+0xafc): undefined reference to `phy_register_fixup_for_id'

This problem was introduced by 48c8b96f
("ARM: shmobile: Lager: add Micrel KSZ8041 PHY fixup")

Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

sh_mmcif driver doesn't care resource name.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Move arch timer workaround code and boot mode pin
handling from setup-r8a7790.c to setup-rcar-gen2.c.

With this in place the same code can be used on
other R-Car Generation 2 devices such as r8a7791.
Signed-off-by: NMagnus Damm <damm@opensource.se>
[horms+renesas@verge.net.au trivial rebase of board-lager.c
 for introduction of lager_add_standard_devices()]
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Move arch timer workaround code and boot mode pin
handling from setup-r8a7790.c to setup-rcar-gen2.c.

With this in place the same code can be used on
other R-Car Generation 2 devices such as r8a7791.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Add r8a7790 SMP support using the shared APMU code. To enable
SMP the r8a7790 specific DTS needs to be updated to include
CPU cores, and this is happening in a separate patch.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

MMCIF on r8a7790 doesn't support Command Completion Signal, but it does
implement a CE_CLK_CTRL2 register. Platform parameters have to be added to
account for these features on lager.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

The DU device erroneously receives the DU resources array as platform
data instead of the DU platform data structure. Fix it.

This problem was introduced by f631fa0 ("ARM: shmobile: lager: Add Display
Unit support").
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>