We pass in the array of ttm pages to be populated in the GART/MM
of the card (or AGP). Patch titled: "ttm: Utilize the DMA API for
pages that have TTM_PAGE_FLAG_DMA32 set." uses the DMA API to make
those pages have a proper DMA addresses (in the situation where
page_to_phys or virt_to_phys do not give use the DMA (bus) address).

Since we are using the DMA API on those pages, we should pass in the
DMA address to this function so it can save it in its proper fields
(later patches use it).

[v2: Added reviewed-by tag]
Reviewed-by: NThomas Hellstrom <thellstrom@shipmail.org>
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Tested-by: NIan Campbell <ian.campbell@citrix.com>

For pages that have the TTM_PAGE_FLAG_DMA32 flag set we
use the DMA API. We save the bus address in our array which we
use to program the GART (see "radeon/ttm/PCIe: Use dma_addr if TTM
has set it." and "nouveau/ttm/PCIe: Use dma_addr if TTM has set it.").

The reason behind using the DMA API is that under Xen we would
end up programming the GART with the bounce buffer (SWIOTLB)
DMA address instead of the physical DMA address of the TTM page.
The reason being that alloc_page with GFP_DMA32 does not allocate
pages under the the 4GB mark when running under Xen hypervisor.

Under baremetal this means we do the DMA API call earlier instead
of when we program the GART.

For details please refer to:
https://lkml.org/lkml/2011/1/7/251

[v2: Fixed indentation, revised desc, added Reviewed-by]
Reviewed-by: NThomas Hellstrom <thomas@shipmail.org>
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Tested-by: NIan Campbell <ian.campbell@citrix.com>

This is right now limited to only non-pool constructs.

[v2: Fixed indentation issues, add review-by tag]
Reviewed-by: NThomas Hellstrom <thomas@shipmail.org>
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Tested-by: NIan Campbell <ian.campbell@citrix.com>

The addition of CONFIG_SECURITY_DMESG_RESTRICT resulted in a build
failure when CONFIG_PRINTK=n.  This is because the capabilities code
which used the new option was built even though the variable in question
didn't exist.

The patch here fixes this by moving the capabilities checks out of the
LSM and into the caller.  All (known) LSMs should have been calling the
capabilities hook already so it actually makes the code organization
better to eliminate the hook altogether.
Signed-off-by: NEric Paris <eparis@redhat.com>
Acked-by: NJames Morris <jmorris@namei.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Merge branch 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6

* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6:
  arm: omap1: devices: need to return with a value
  OMAP1: camera.h: add missing include
  omap: dma: Add read-back to DMA interrupt handler to avoid spuriousinterrupts
  OMAP2: Devkit8000: Fix mmc regulator failure

* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
  hwmon: (w83795) Check for BEEP pin availability
  hwmon: (w83795) Clear intrusion alarm immediately
  hwmon: (w83795) Read the intrusion state properly
  hwmon: (w83795) Print the actual temperature channels as sources
  hwmon: (w83795) List all usable temperature sources
  hwmon: (w83795) Expose fan control method
  hwmon: (w83795) Fix fan control mode attributes
  hwmon: (lm95241) Check validity of input values
  hwmon: Change mail address of Hans J. Koch

* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
  i2c: Sanity checks on adapter registration
  i2c: Mark i2c_adapter.id as deprecated
  i2c: Drivers shouldn't include <linux/i2c-id.h>
  i2c: Delete unused adapter IDs
  i2c: Remove obsolete cleanup for clientdata

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
  PCI: sysfs: fix printk warnings
  PCI: fix pci_bus_alloc_resource() hang, prefer positive decode
  PCI: read current power state at enable time
  PCI: fix size checks for mmap() on /proc/bus/pci files
  x86/PCI: coalesce overlapping host bridge windows
  PCI hotplug: ibmphp: Add check to prevent reading beyond mapped area

Make sure I2C adapters being registered have the required struct
fields set. If they don't, problems will happen later.
Signed-off-by: NJean Delvare <khali@linux-fr.org>

It's about time to make it clear that i2c_adapter.id is deprecated.
Hopefully this will remind the last user to move over to a different
strategy.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Acked-by: NJarod Wilson <jarod@redhat.com>
Acked-by: NMauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: NHans Verkuil <hverkuil@xs4all.nl>

Drivers don't need to include <linux/i2c-id.h>, especially not when
they don't use anything that header file provides.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: Michael Hunold <michael@mihu.de>
Acked-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Delete unused I2C adapter IDs. Special cases are:

* I2C_HW_B_RIVA was still set in driver rivafb, however no other
  driver is ever looking for this value, so we can safely remove it.
* I2C_HW_B_HDPVR is used in staging driver lirc_zilog, however no
  adapter ID is ever set to this value, so the code in question never
  runs. As the code additionally expects that I2C_HW_B_HDPVR may not
  be defined, we can delete it now and let the lirc_zilog driver
  maintainer rewrite this piece of code.

Big thanks for Hans Verkuil for doing all the hard work :)
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Acked-by: NJarod Wilson <jarod@redhat.com>
Acked-by: NMauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: NHans Verkuil <hverkuil@xs4all.nl>

A few new i2c-drivers came into the kernel which clear the clientdata-pointer
on exit. This is obsolete meanwhile, so fix it and hope the word will spread.
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Acked-by: NAlan Cox <alan@linux.intel.com>
Acked-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Move the logging bits from kernel.h into printk.h so that
there is a bit more logical separation of the generic from
the printk logging specific parts.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The fix in commit 6b4e81db ("i8k: Tell gcc that *regs gets
clobbered") to work around the gcc miscompiling i8k.c to add "+m
(*regs)" caused register pressure problems and a build failure.

Changing the 'asm' statement to 'asm volatile' instead should prevent
that and works around the gcc bug as well, so we can remove the "+m".

[ Background on the gcc bug: a memory clobber fails to mark the function
  the asm resides in as non-pure (aka "__attribute__((const))"), so if
  the function does nothing else that triggers the non-pure logic, gcc
  will think that that function has no side effects at all. As a result,
  callers will be mis-compiled.

  Adding the "+m" made gcc see that it's not a pure function, and so
  does "asm volatile". The problem was never really the need to mark
  "*regs" as changed, since the memory clobber did that part - the
  problem was just a bug in the gcc "pure" function analysis  - Linus ]
Signed-off-by: NJim Bos <jim876@xs4all.nl>
Acked-by: NJakub Jelinek <jakub@redhat.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

On the W83795ADG, there's a single pin for BEEP and OVT#, so you
can't have both. Check the configuration and don't create beep
attributes when BEEP pin is not available.

The W83795G has a dedicated BEEP pin so the functionality is always
available there.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Acked-by: NGuenter Roeck <guenter.roeck@ericsson.com>

When asked to clear the intrusion alarm, do so immediately. We have to
invalidate the cache to make sure the new status will be read. But we
also have to read from the status register once to clear the pending
alarm, as writing to CLR_CHS surprising won't clear it automatically.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Acked-by: NGuenter Roeck <guenter.roeck@ericsson.com>

We can't read the intrusion state from the real-time alarm registers
as we do for all other alarm flags, because real-time alarm bits don't
stick (by definition) and the intrusion state has to stick until
explicitly cleared (otherwise it has little value.)

So we have to use the interrupt status register instead, which is read
from the same address but with a configuration bit flipped in another
register.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Acked-by: NGuenter Roeck <guenter.roeck@ericsson.com>

Don't expose raw register values to user-space. Decode and encode
temperature channels selected as temperature sources as needed.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Acked-by: NGuenter Roeck <guenter.roeck@ericsson.com>

Temperature sources are not correlated directly with temperature
channels. A look-up table is required to find out which temperature
sources can be used depending on which temperature channels (both
analog and digital) are enabled.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Acked-by: NGuenter Roeck <guenter.roeck@ericsson.com>

Expose fan control method (DC vs. PWM) using the standard sysfs
attributes. I've made it read-only as the board should be wired for
a given mode, the BIOS should have set up the chip for this mode, and
you shouldn't have to change it. But it would be easy enough to make
it changeable if someone comes up with a use case.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Acked-by: NGuenter Roeck <guenter.roeck@ericsson.com>

There were two bugs:
* Speed cruise mode was improperly reported for all fans but fan1.
* Fan control method (PWM vs. DC) was mixed with the control mode.
  It will be added back as a separate attribute, as per the standard
  sysfs interface.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Acked-by: NGuenter Roeck <guenter.roeck@ericsson.com>

This clears the following build-time warnings I was seeing:

drivers/hwmon/lm95241.c: In function "set_interval":
drivers/hwmon/lm95241.c:132:15: warning: ignoring return value of "strict_strtol", declared with attribute warn_unused_result
drivers/hwmon/lm95241.c: In function "set_max2":
drivers/hwmon/lm95241.c:278:1: warning: ignoring return value of "strict_strtol", declared with attribute warn_unused_result
drivers/hwmon/lm95241.c: In function "set_max1":
drivers/hwmon/lm95241.c:277:1: warning: ignoring return value of "strict_strtol", declared with attribute warn_unused_result
drivers/hwmon/lm95241.c: In function "set_min2":
drivers/hwmon/lm95241.c:249:1: warning: ignoring return value of "strict_strtol", declared with attribute warn_unused_result
drivers/hwmon/lm95241.c: In function "set_min1":
drivers/hwmon/lm95241.c:248:1: warning: ignoring return value of "strict_strtol", declared with attribute warn_unused_result
drivers/hwmon/lm95241.c: In function "set_type2":
drivers/hwmon/lm95241.c:220:1: warning: ignoring return value of "strict_strtol", declared with attribute warn_unused_result
drivers/hwmon/lm95241.c: In function "set_type1":
drivers/hwmon/lm95241.c:219:1: warning: ignoring return value of "strict_strtol", declared with attribute warn_unused_result

This also fixes a small race in set_interval() as a side effect: by
working with a temporary local variable we prevent data->interval from
being accessed at a time it contains the interval value in the wrong
unit.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: Davide Rizzo <elpa.rizzo@gmail.com>

My old mail address doesn't exist anymore. This changes all occurrences
to my new address.
Signed-off-by: NHans J. Koch <hjk@hansjkoch.de>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Cast pci_resource_start() and pci_resource_len() to u64 for printk.

drivers/pci/pci-sysfs.c:753: warning: format '%16Lx' expects type 'long long unsigned int', but argument 9 has type 'resource_size_t'
drivers/pci/pci-sysfs.c:753: warning: format '%16Lx' expects type 'long long unsigned int', but argument 10 has type 'resource_size_t'
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

* git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-2.6-fixes:
  GFS2: Fix inode deallocation race

Merge branch 's5p-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung

* 's5p-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
  ARM: SAMSUNG: Fix HAVE_S3C_RTC warnings
  ARM: SAMSUNG: Fix HAVE_S3C2410_I2C warnings
  ARM: SAMSUNG: Fix HAVE_S3C2410_WATCHDOG warnings

Merge branch 'fbdev-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/fbdev-2.6

* 'fbdev-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/fbdev-2.6:
  fsl-diu-fb: drop dead ioctl define
  MAINTAINERS: Add an fbdev git tree entry.
  OMAP: DSS: Fix documentation regarding 'vram' kernel parameter
  OMAP: VRAM: Fix boot-time memory allocation
  OMAP: VRAM: improve VRAM error prints
  sisfb: limit POST memory test according to PCI resource length
  fbdev: sh_mobile_lcdc: use correct number of modes, when using the default
  fbdev: sh_mobile_lcdc: use the standard CEA-861 720p timing
  fbdev: sh_mobile_hdmi: properly clean up modedb on monitor unplug

Merge branches 'sh-fixes-for-linus' and 'rmobile-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6

* 'sh-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
  sh: intc: Fix up build failure introduced by radix tree changes.
  MAINTAINERS: update the sh git tree entry.
  sh: clkfwk: fix up compiler warnings.
  sh: intc: Fix up initializers for gcc 4.5.
  rtc: rtc-sh - fix a memory leak

* 'rmobile-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
  ARM: mach-shmobile: ap4evb: add fsib 44100Hz rate
  MAINTAINERS: update the ARM SH-Mobile git tree entry.
  ARM: mach-shmobile: ap4evb: Mark NOR boot loader partitions read-only.
  ARM: mach-shmobile: intc-sh7372: fix interrupt number

This area of the code has always been a bit delicate due to the
subtleties of lock ordering. The problem is that for "normal"
alloc/dealloc, we always grab the inode locks first and the rgrp lock
later.

In order to ensure no races in looking up the unlinked, but still
allocated inodes, we need to hold the rgrp lock when we do the lookup,
which means that we can't take the inode glock.

The solution is to borrow the technique already used by NFS to solve
what is essentially the same problem (given an inode number, look up
the inode carefully, checking that it really is in the expected
state).

We cannot do that directly from the allocation code (lock ordering
again) so we give the job to the pre-existing delete workqueue and
carry on with the allocation as normal.

If we find there is no space, we do a journal flush (required anyway
if space from a deallocation is to be released) which should block
against the pending deallocations, so we should always get the space
back.
Signed-off-by: NSteven Whitehouse <swhiteho@redhat.com>

Tested-by: NTony SIM <chinyeow.sim.xt@renesas.com>
Tested-by: NTAKEI Mitsuharu <takei.andr@gmail.com>
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

The radix tree retry logic got a bit of an overhaul and subsequently
broke the virtual IRQ subgroup build. Simply switch over to
radix_tree_deref_retry() as per the filemap changes, which the virq
lookup logic was modelled after in the first place.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6 into sh/urgent

The fsl-diu-fb driver no longer uses this define, and we have a common one
to cover this already (FBIO_WAITFORVSYNC).
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Now that there's an fbdev git tree (this is also what is pulled in to
-next), stub it in to the MAINTAINERS entry.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/slab-2.6:
  slub: Fix slub_lock down/up imbalance

* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jlbec/ocfs2:
  ocfs2: Change some lock status member in ocfs2_lock_res to char.

There are two places, that do not release the slub_lock.

Respective bugs were introduced by sysfs changes ab4d5ed5 (slub: Enable
sysfs support for !CONFIG_SLUB_DEBUG) and 2bce6485 ( slub: Allow removal
of slab caches during boot).
Acked-by: NChristoph Lameter <cl@linux.com>
Signed-off-by: NPavel Emelyanov <xemul@openvz.org>
Signed-off-by: NPekka Enberg <penberg@kernel.org>