This patch adds a new "psmap" file to spufs that allows mmap of all of
the problem state mapping of SPEs. It is compatible with 64k pages. In
addition, it removes mmap ability of individual files when using 64k
pages, with the exception of signal1 and signal2 which will both map the
entire 64k page holding both registers. It also removes
CONFIG_SPUFS_MMAP as there is no point in not building mmap support in
spufs.

It goes along a separate patch to libspe implementing usage of that new
file to access problem state registers.

Another patch will follow up to fix races opened up by accessing
the 'runcntl' register directly, which is made possible with this
patch.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NArnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

If you lose the x bit (eg: by using patch(1)), powerpc won't build.  Be
defensive about it...

Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This adds defines for the hypertransport capability subtypes and starts
using them a little.

[akpm@osdl.org: fix typo]
Signed-off-by: NEric W. Biederman <ebiederm@xmission.com>
Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

kbuild explicitly includes this at build time.
Signed-off-by: NDave Jones <davej@redhat.com>

Add support for MPC832x MDS evaluation board.

This patch depends on the 8360+QE lib patches by Leo.

The MPC832x processors (MPC8323E, MPC8323, MPC8321E, MPC8321) sport
the e300c2 core plus a QUICC Engine (QE).  This patch adds support for
the 832x MDS evaluation board.

The 832x MDS dts and defconfig files are pending more tests.
Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Add support for the Freescale e300c2 core found in the MPC832x processor line.

As far as initial kernel support is concerned, the e300c2 core is
identical to the e300c1 found in the mpc834x, except that it's had its
floating point unit chopped off.
Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Add MPC8360EMDS default device-tree source file
Signed-off-by: NLi Yang <leoli@freescale.com>
Signed-off-by: NJiang Bo <Tanya.jiang@freescale.com>
Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The patch adds MPC8360EMDS board support.
Signed-off-by: NLi Yang <leoli@freescale.com>
Signed-off-by: NYin Olivia <hong-hua.yin@freescale.com>
Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Add QUICC Engine (QE) configuration, header files, and
QE management and library code that are used by QE devices
drivers.

Includes Leo's modifications up to, and including, the
platform_device to of_device adaptation:

"The series of patches add generic QE infrastructure called
qe_lib, and MPC8360EMDS board support.  Qe_lib is used by
QE device drivers such as ucc_geth driver.

This version updates QE interrupt controller to use new irq
mapping mechanism, addresses all the comments received with
last submission and includes some style fixes.

v2: Change to use device tree for BCSR and MURAM;
Remove I/O port interrupt handling code as it is not generic
enough.

v3: Address comments from Kumar;  Update definition of several
device tree nodes;  Copyright style change."

In addition, the following changes have been made:

o removed typedefs
o uint -> u32 conversions
o removed following defines:
  QE_SIZEOF_BD, BD_BUFFER_ARG, BD_BUFFER_CLEAR, BD_BUFFER,
  BD_STATUS_AND_LENGTH_SET, BD_STATUS_AND_LENGTH, and BD_BUFFER_SET
  because they hid sizeof/in_be32/out_be32 operations from the reader.
o fixed qe_snums_init() serial num assignment to use a const array
o made CONFIG_UCC_FAST select UCC_SLOW
o reduced NR_QE_IC_INTS from 128 to 64
o remove _IO_BASE, etc. defines (not used)
o removed irrelevant comments, added others to resemble removed BD_ defines
o realigned struct definitions in headers
o various other style fixes including things like pinMask -> pin_mask
o fixed a ton of whitespace issues
o marked ioregs as __be32/__be16
o removed platform_device code and redundant get_qe_base()
o removed redundant comments
o added cpu_relax() to qe_reset
o uncasted all get_property() assignments
o eliminated unneeded casts
o eliminated immrbar_phys_to_virt (not used)
Signed-off-by: NLi Yang <leoli@freescale.com>
Signed-off-by: NShlomi Gridish <gridish@freescale.com>
Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Currently, if xmon has no input device (as is generally the case on
G5 powermacs), and we drop into xmon as a result of a fatal exception,
it will return 1, which die() interprets as "continue without causing
an oops".  This fixes it by making xmon() return 0 in the case where
it has no input device.
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This should probably say "mpic" to save confusion.
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>
Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

On powermac, when open firmware is set to use the SCC for console, this
causes the low level udbg early console to read back the speed and
re-use it instead of hard coding 57600 bps. This doesn't (yet) pass the
detected speed all the way to pmac_zilog though.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Recent changes to the PowerPC zImage wrapper broke zImage.coff due to
the addition of new ELF sections that aren't very well converted to
xcoff and not supported by old OpenFirmware. This fixes it by putting
those sections in the xcoff .data.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

My patch to make the early xmon logic work with earlier early param
parsing (480f6f35) breaks xmon=off.

No one does this obviously as xmon rocks, but it should really work
as documented.

While fixing that it struck me that we could move the xmon param
handling into xmon.c, and also consolidate the
xmon_init()/do_early_xmon logic into xmon_setup(). This means
xmon=early drops into xmon a little earlier on 32-bit, but it
seems to work just fine.

Tested on PSERIES and CLASSIC32.
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This patch reworks the cell iic interrupt handling so that:

 - Node ID is back in the interrupt number (only one IRQ host is created
for all nodes). This allows interrupts from sources on another node to
be routed non-locally. This will allow possibly one day to fix maxcpus=1
or 2 and still get interrupts from devices on BE 1. (A bit more fixing
is needed for that) and it will allow us to implement actual affinity
control of external interrupts.

 - Added handling of the IO exceptions interrupts (badly named, but I
re-used the name initially used by STI). Those are the interrupts
exposed by IIC_ISR and IIC_IRR, such as the IOC translation exception,
performance monitor, etc... Those get their special numbers in the IRQ
number space and are internally implemented as a cascade on unit 0xe,
class 1 of each node.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: NArnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Many files include the filename at the beginning, serveral used a wrong one.
Signed-off-by: NUwe Zeisberger <Uwe_Zeisberger@digi.com>
Signed-off-by: NAdrian Bunk <bunk@stusta.de>

The patch below corrects multiple occurances of "the the"
typos across several files, both in source comments and KConfig files.
There is no actual code changed, only text.  Note this only affects the /arch
directory, and I believe I could find many more elsewhere. :)
Signed-off-by: NAdrian Bunk <bunk@stusta.de>

This intruduces 82xx family in arch/powerpc/platforms,
and has all the board-specific code to represent regression-less
transaction from ppc. The functionality is apparently the same, including
PCI controller.
Signed-off-by: NVitaly Bordug <vbordug@ru.mvista.com>

This has modules of common directories related to the
mpc8272ADS board, mainly common cpm2 changes and fsl_soc.c
portions related to the bitbang MDIO and other mechanisms specific
for this family.
Signed-off-by: NVitaly Bordug <vbordug@ru.mvista.com>

This adds current dts file used with MPC8272ADS,
introducing new mdio bitbang defines, as well as
fully-CPM2-SoC board design.
Signed-off-by: NVitaly Bordug <vbordug@ru.mvista.com>

The last change for partport_pc did fix the common case for all PowerMacs,
but it broke the case for PCI multiport IO cards.  In fact, the config
option CONFIG_PARPORT_PC_SUPERIO=y lead to a hard crash when cups probed
the parport driver.  It enables the winbond and smsc probing.

Remove the PARPORT_BASE check again, parport_pc_find_nonpci_ports() will
take care of it.  All powerpc configs should have
CONFIG_PARPORT_PC_SUPERIO=n, the code did not find anything on the chrp
boards we tested it on.

Tested on a G4/466 with a PCI card:

0001:10:13.0 Serial controller: Timedia Technology Co Ltd PCI2S550 (Dual 16550 UART) (rev 01) (prog-if 02 [16550])
        Subsystem: Timedia Technology Co Ltd Unknown device 5079
        Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Interrupt: pin A routed to IRQ 53
        Region 0: I/O ports at f2000800 [size=32]
        Region 2: I/O ports at f2000870 [size=8]
        Region 3: I/O ports at f2000860 [size=8]
Signed-off-by: NOlaf Hering <olaf@aepfle.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Adam Belay <ambx1@neo.rr.com>
Cc: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

These patches make the kernel pass 64-bit inode numbers internally when
communicating to userspace, even on a 32-bit system.  They are required
because some filesystems have intrinsic 64-bit inode numbers: NFS3+ and XFS
for example.  The 64-bit inode numbers are then propagated to userspace
automatically where the arch supports it.

Problems have been seen with userspace (eg: ld.so) using the 64-bit inode
number returned by stat64() or getdents64() to differentiate files, and
failing because the 64-bit inode number space was compressed to 32-bits, and
so overlaps occur.

This patch:

Make filldir_t take a 64-bit inode number and struct kstat carry a 64-bit
inode number so that 64-bit inode numbers can be passed back to userspace.

The stat functions then returns the full 64-bit inode number where
available and where possible.  If it is not possible to represent the inode
number supplied by the filesystem in the field provided by userspace, then
error EOVERFLOW will be issued.

Similarly, the getdents/readdir functions now pass the full 64-bit inode
number to userspace where possible, returning EOVERFLOW instead when a
directory entry is encountered that can't be properly represented.

Note that this means that some inodes will not be stat'able on a 32-bit
system with old libraries where they were before - but it does mean that
there will be no ambiguity over what a 32-bit inode number refers to.

Note similarly that directory scans may be cut short with an error on a
32-bit system with old libraries where the scan would work before for the
same reasons.

It is judged unlikely that this situation will occur because modern glibc
uses 64-bit capable versions of stat and getdents class functions
exclusively, and that older systems are unlikely to encounter
unrepresentable inode numbers anyway.

[akpm: alpha build fix]
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>

and use it an all the obvious places in assembler code.
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>

Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>

This will build with ISERIES, PSERIES and PMAC64 selected, but will only
boot on iSeries so far.
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>

There are a few places in the kernel where the init task is signaled.  The
ctrl+alt+del sequence is one them.  It kills a task, usually init, using a
cached pid (cad_pid).

This patch replaces the pid_t by a struct pid to avoid pid wrap around
problem.  The struct pid is initialized at boot time in init() and can be
modified through systctl with

	/proc/sys/kernel/cad_pid

[ I haven't found any distro using it ? ]

It also introduces a small helper routine kill_cad_pid() which is used
where it seemed ok to use cad_pid instead of pid 1.

[akpm@osdl.org: cleanups, build fix]
Signed-off-by: NCedric Le Goater <clg@fr.ibm.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Some architectures provide an execve function that does not set errno, but
instead returns the result code directly.  Rename these to kernel_execve to
get the right semantics there.  Moreover, there is no reasone for any of these
architectures to still provide __KERNEL_SYSCALLS__ or _syscallN macros, so
remove these right away.

[akpm@osdl.org: build fix]
[bunk@stusta.de: build fix]
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Cc: Andi Kleen <ak@muc.de>
Acked-by: NPaul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ian Molton <spyro@f2s.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Hirokazu Takata <takata.hirokazu@renesas.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Kazumoto Kojima <kkojima@rr.iij4u.or.jp>
Cc: Richard Curnow <rc@rc0.org.uk>
Cc: William Lee Irwin III <wli@holomorphy.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Miles Bader <uclinux-v850@lsi.nec.co.jp>
Cc: Chris Zankel <chris@zankel.net>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

In some places, particularly drivers and __init code, the init utsns is the
appropriate one to use.  This patch replaces those with a the init_utsname
helper.

Changes: Removed several uses of init_utsname().  Hope I picked all the
	right ones in net/ipv4/ipconfig.c.  These are now changed to
	utsname() (the per-process namespace utsname) in the previous
	patch (2/7)

[akpm@osdl.org: CIFS fix]
Signed-off-by: NSerge E. Hallyn <serue@us.ibm.com>
Cc: Kirill Korotaev <dev@openvz.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Herbert Poetzl <herbert@13thfloor.at>
Cc: Andrey Savochkin <saw@sw.ru>
Cc: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Replace references to system_utsname to the per-process uts namespace
where appropriate.  This includes things like uname.

Changes: Per Eric Biederman's comments, use the per-process uts namespace
	for ELF_PLATFORM, sunrpc, and parts of net/ipv4/ipconfig.c

[jdike@addtoit.com: UML fix]
[clg@fr.ibm.com: cleanup]
[akpm@osdl.org: build fix]
Signed-off-by: NSerge E. Hallyn <serue@us.ibm.com>
Cc: Kirill Korotaev <dev@openvz.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Herbert Poetzl <herbert@13thfloor.at>
Cc: Andrey Savochkin <saw@sw.ru>
Signed-off-by: NCedric Le Goater <clg@fr.ibm.com>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Move the init_nsproxy definition out of arch/ into kernel/nsproxy.c.  This
avoids all arches having to be updated.  Compiles and boots on s390.
Signed-off-by: NSerge E. Hallyn <serue@us.ibm.com>
Cc: Kirill Korotaev <dev@openvz.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Herbert Poetzl <herbert@13thfloor.at>
Cc: Andrey Savochkin <saw@sw.ru>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This patch adds a nsproxy structure to the task struct.  Later patches will
move the fs namespace pointer into this structure, and introduce a new utsname
namespace into the nsproxy.

The vserver and openvz functionality, then, would be implemented in large part
by virtualizing/isolating more and more resources into namespaces, each
contained in the nsproxy.

[akpm@osdl.org: build fix]
Signed-off-by: NSerge Hallyn <serue@us.ibm.com>
Cc: Kirill Korotaev <dev@openvz.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Herbert Poetzl <herbert@13thfloor.at>
Cc: Andrey Savochkin <saw@sw.ru>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

kprobe_flush_task() possibly calls kfree function during holding
kretprobe_lock spinlock, if kfree function is probed by kretprobe that will
incur spinlock deadlock.  This patch moves kfree function out scope of
kretprobe_lock.
Signed-off-by: Nbibo, mao <bibo.mao@intel.com>
Signed-off-by: NAnanth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Whitespace is used to indent, this patch cleans up these sentences by
kernel coding style.
Signed-off-by: Nbibo, mao <bibo.mao@intel.com>
Signed-off-by: NAnanth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

In an effort to make kprobe modules more portable, here is a patch that:

o Introduces the "symbol_name" field to struct kprobe.
  The symbol->address resolution now happens in the kernel in an
  architecture agnostic manner. 64-bit powerpc users no longer have
  to specify the ".symbols"
o Introduces the "offset" field to struct kprobe to allow a user to
  specify an offset into a symbol.
o The legacy mechanism of specifying the kprobe.addr is still supported.
  However, if both the kprobe.addr and kprobe.symbol_name are specified,
  probe registration fails with an -EINVAL.
o The symbol resolution code uses kallsyms_lookup_name(). So
  CONFIG_KPROBES now depends on CONFIG_KALLSYMS
o Apparantly kprobe modules were the only legitimate out-of-tree user of
  the kallsyms_lookup_name() EXPORT. Now that the symbol resolution
  happens in-kernel, remove the EXPORT as suggested by Christoph Hellwig
o Modify tcp_probe.c that uses the kprobe interface so as to make it
  work on multiple platforms (in its earlier form, the code wouldn't
  work, say, on powerpc)
Signed-off-by: NAnanth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: NPrasanna S Panchamukhi <prasanna@in.ibm.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Honor alignment parameter in the rheap allocator.  This is needed by
qe_lib.
Remove compile warning.
Signed-off-by: NPantelis Antoniou <pantelis@embeddedalley.com>
Signed-off-by: NLi Yang <leoli@freescale.com>
Acked-by: NKumar Galak <galak@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Add powerpc get/set_rtc_time interface to new generic rtc class. This
abstracts rtc chip specific code from the platform code for rtc-over-i2c
platforms.  Specific RTC chip support is now configured under
Device Drivers -> Real Time Clock. Setting time of day from the RTC
on startup is also configurable.

this time without the potentially platform breaking initcall.
Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

With 2.6.18-rc4-mm2, now wall_jiffies will always be the same as jiffies.
So we can kill wall_jiffies completely.

This is just a cleanup and logically should not change any real behavior
except for one thing: RTC updating code in (old) ppc and xtensa use a
condition "jiffies - wall_jiffies == 1".  This condition is never met so I
suppose it is just a bug.  I just remove that condition only instead of
kill the whole "if" block.

[heiko.carstens@de.ibm.com: s390 build fix and cleanup]
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Andi Kleen <ak@muc.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ian Molton <spyro@f2s.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Hirokazu Takata <takata.hirokazu@renesas.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Kazumoto Kojima <kkojima@rr.iij4u.or.jp>
Cc: Richard Curnow <rc@rc0.org.uk>
Cc: William Lee Irwin III <wli@holomorphy.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Miles Bader <uclinux-v850@lsi.nec.co.jp>
Cc: Chris Zankel <chris@zankel.net>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

All on stack DECLARE_COMPLETIONs should be replaced by:
DECLARE_COMPLETION_ONSTACK
Signed-off-by: NPeter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: NIngo Molnar <mingo@elte.hu>
Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>