Impact: timer hang on CPU online observed on AMD C1E systems

When a CPU is brought online then the broadcast machinery can
be in the one shot state already. Check this and setup the timer 
device of the new CPU in one shot mode so the broadcast code
can pick up the next_event value correctly.

Another AMD C1E oddity, as we switch to broadcast immediately and
not after the full bring up via the ACPI cpu idle code.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

Impact: Possible hang on CPU online observed on AMD C1E machines.

The broadcast setup code looks at the mode of the tick device to
determine whether it needs to be shut down or setup. This is wrong
when the broadcast mode is set to one shot already. This can happen
when a CPU is brought online as it goes through the periodic setup
first.

The problem went unnoticed as sane systems do not call into that code
before the switch to one shot for the clock event device happens.
The AMD C1E idle routine switches over immediately and thereby shuts
down the just setup device before the first interrupt happens.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

Impact: possible hang on CPU onlining in timer one shot mode.

The tick_next_period variable is only used during boot on nohz/highres
enabled systems, but for CPU onlining it needs to be maintained when
the per cpu clock events device operates in one shot mode.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

Impact: hang which happens across CPU offline/online on AMD C1E systems.

When a CPU goes offline then the corresponding bit in the broadcast
mask is cleared. For AMD C1E enabled CPUs we do not reenable the
broadcast when the CPU comes online again as we do not clear the
corresponding bit in the c1e_mask, which keeps track which CPUs
have been switched to broadcast already. So on those !$@#& machines
we never switch back to broadcasting after a CPU offline/online cycle.

Clear the bit when the CPU plays dead.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

Impact: rare hang which can be triggered on CPU online.

tick_do_timer_cpu keeps track of the CPU which updates jiffies
via do_timer. The value -1 is used to signal, that currently no
CPU is doing this. There are two cases, where the variable can 
have this state:

 boot:
    necessary for systems where the boot cpu id can be != 0

 nohz long idle sleep:
    When the CPU which did the jiffies update last goes into
    a long idle sleep it drops the update jiffies duty so
    another CPU which is not idle can pick it up and keep
    jiffies going.

Using the same value for both situations is wrong, as the CPU online
code can see the -1 state when the timer of the newly onlined CPU is
setup. The setup for a newly onlined CPU goes through periodic mode
and can pick up the do_timer duty without being aware of the nohz /
highres mode of the already running system.

Use two separate states and make them constants to avoid magic
numbers confusion. 
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

* 'hwmon-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
  hwmon: (ad7414) Make ad7414_update_device() static
  hwmon: (it87) Fix fan tachometer reading in IT8712F rev 0x7 (I)
  hwmon: (atxp1) Fix device detection logic

* 'kvm-updates/2.6.27' of git://git.kernel.org/pub/scm/linux/kernel/git/avi/kvm:
  KVM: ia64: 'struct fdesc' build fix

* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
  [MIPS] vmlinux.lds.S: handle .text.*
  [MIPS] Fix potential latency problem due to non-atomic cpu_wait.
  [MIPS] SMTC: Clear TIF_FPUBOUND on clone / fork.
  [MIPS] Fix 64-bit IP checksum code

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc:
  mmc_test: initialize mmc_test_lock statically
  mmc_block: handle error from mmc_register_driver()
  atmel-mci: Set MMC_CAP_NEEDS_POLL if no detect_pin
  atmel-mci: Fix bogus debugfs file size
  atmel-mci: Fix memory leak in atmci_regs_show
  atmel-mci: debugfs: enable clock before dumping regs
  tmio_mmc: fix compilation with debug enabled

* Normalize some S: entries to match the enumeration at the beginning
  of the file.
* Change one mailing list entry from S: to L:.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* Drop trailing whitespace.
* Replace spaces and combinations of spaces and tabs by single tabs.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The -ffunction-sections puts each text in .text.function_name section.
Without this patch, most functions are placed outside _text..._etext
area and it breaks show_stacktrace(), etc.
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

If an interrupt happened between checking of NEED_RESCHED and WAIT
instruction, adjust EPC to restart from checking of NEED_RESCHED.
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Use unsigned loads to avoid possible misscalculation of IP checksums.  This
bug was instruced in f761106cd728bcf65b7fe161b10221ee00cf7132 (lmo) /
ed99e2bc (kernel.org).

[Original fix by Atsushi.  Improved instruction scheduling and fix for
unaligned unsigned load by me -- Ralf]
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The mutex mmc_test_lock is initialized at every time mmc_test device
is probed. Probing another mmc_test device may break the mutex, if
the probe function is called while the mutex is locked.

This patch fixes it by statically initializing mmc_test_lock.
Signed-off-by: NAkinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Check error from mmc_register_driver() and properly unwind
block device registration.
Signed-off-by: NAkinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

This allows the mmc core to detect card insertion/removal for slots that
don't have any CD pin wired up.
Signed-off-by: NHaavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

We used to store a binary register snapshot in the "regs" file, so we
set the file size to be the size of this snapshot. This is no longer
valid since we switched to using seq_file.
Signed-off-by: NHaavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

The debugfs hook atmci_regs_show allocates a temporary buffer for
storing a register snapshot, but it doesn't free it before returning.
Plug this leak.
Signed-off-by: NHaavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Make sure that the peripheral clock is enabled before reading the MMIO
registers for the debugfs "regs" dump.
Signed-off-by: NHaavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Signed-off-by: NDmitry Baryshkov <dbaryshkov@gmail.com>
Acked-by: NIan Molton <spyro@f2s.com>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

This patch makes the needlessly global ad7414_update_device() static.
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Acked-by: NSean MacLennan <smaclennan@pikatech.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

The IT8712F v0.9.1 datasheet applies to revisions >= 0x8 (J).
The driver was incorrectly attempting to enable 16-bit fan
readings on rev 0x7 (I) which led to incorrect RPM values.
Signed-off-by: NAndrew Paprocki <andrew@ishiboo.com>
Tested-by: NJohn Gumb <john.gumb@tandberg.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

The atxp1 device detection code has a major logic flaw, fix it. Not
sure how we managed to miss this when the driver was merged...
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Acked-by: NSebastian Witt <se.witt@gmx.net>

Commit 4611a771 ("[IA64] fix compile failure with non modular builds")
introduced struct fdesc into asm/elf.h, which duplicates KVM's definition.
Remove the latter to avoid the build error.
Signed-off-by: NJes Sorensen <jes@sgi.com>
Acked-by: NTony Luck <tony.luck@intel.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6:
  [S390] cio: fix orb initialization in cio_start_key
  [S390] cio: Fix driver_data handling for ccwgroup devices.

* git://oss.sgi.com:8090/xfs/linux-2.6:
  [XFS] Don't do I/O beyond eof when unreserving space
  [XFS] Fix use-after-free with buffers
  [XFS] Prevent lockdep false positives when locking two inodes.
  [XFS] Fix barrier status change detection.
  [XFS] Prevent direct I/O from mapping extents beyond eof
  [XFS] Fix regression introduced by remount fixup
  [XFS] Move memory allocations for log tracing out of the critical path

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
  IPoIB: Fix deadlock on RTNL between bcast join comp and ipoib_stop()
  RDMA/nes: Fix client side QP destroy
  IB/mlx4: Fix up fast register page list format
  mlx4_core: Set RAE and init mtt_sz field in FRMR MPT entries

Merge branch 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  sched: fix deadlock in setting scheduler parameter to zero
  sched: fix 2.6.27-rc5 couldn't boot on tulsa machine randomly

Merge branch 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  clockevents: make device shutdown robust
  clocksource, acpi_pm.c: fix check for monotonicity
  clockevents: remove WARN_ON which was used to gather information

Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  x86: completely disable NOPL on 32 bits
  x86/paravirt: Remove duplicate paravirt_pagetable_setup_{start, done}()
  xen: fix for xen guest with mem > 3.7G
  x86: fix possible x86_64 and EFI regression
  arch/x86/kernel/kdebugfs.c: introduce missing kfree

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
  Fix compile failure with non modular builds
  powerpc: Holly board needs dtbImage target
  powerpc: Fix interrupt values for DMA2 in MPC8610 HPCD device tree

* master.kernel.org:/home/rmk/linux-2.6-arm:
  [ARM] 5255/1: Update jornada ssp to remove build errors/warnings
  [ARM] omap: back out 'internal_clock' support
  [ARM] 5249/1: davinci: remove redundant check in davinci_psc_config()

* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/hskinnemoen/avr32-2.6:
  avr32: nmi_enter() without nmi_exit()
  avr32: fix sys_sync_file_range() call convention
  avr32: add generic_find_next_le_bit bit function
  avr32: add .gitignore files
  atstk1000: fix build breakage with BOARD_ATSTK100X_SW2_CUSTOM=y

* 'for-linus' of git://neil.brown.name/md:
  md: Don't wait UNINTERRUPTIBLE for other resync to finish

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
  sparc64: Fix SMP bootup with CONFIG_STACK_DEBUG or ftrace.
  sparc64: Fix OOPS in psycho_pcierr_intr_other().

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
  e100: Use pci_pme_active to clear PME_Status and disable PME#
  e1000: prevent corruption of EEPROM/NVM
  forcedeth: call restore mac addr in nv_shutdown path
  bnx2: Promote vector field in bnx2_irq structure from u16 to unsigned int
  sctp: Fix oops when INIT-ACK indicates that peer doesn't support AUTH
  sctp: do not enable peer features if we can't do them.
  sctp: set the skb->ip_summed correctly when sending over loopback.
  udp: Fix rcv socket locking

While updating the rcu code, I noticed that do_nmi() for AVR32 is odd:
There is an nmi_enter() call without an nmi_exit().
This can't be correct, it breaks rcu (at least the preempt version) and
lockdep.

[haavard.skinnemoen@atmel.com: fixed another case that returned directly]
Signed-off-by: NHaavard Skinnemoen <haavard.skinnemoen@atmel.com>