MX is an interrupt distributor used in some SMP-capable xtensa
configurations.
Signed-off-by: NMax Filippov <jcmvbkbc@gmail.com>
Signed-off-by: NChris Zankel <chris@zankel.net>

PIC irq_ack doesn't clear timer IRQ, because timer interrupt handler
usually set up new timer by writing to ccompare register and thus
clearing timer IRQ. However timer may not be set up in the IRQ handler,
e.g. with tickless idle on SMP, or when CPU is going offline, leaving
timer IRQ raised and making do_interrupt attempting to handle it
forever.

To fix this always write current value of ccompare SR chosen to be linux
timer back to that SR on entry to timer interrupt handler.
Signed-off-by: NMax Filippov <jcmvbkbc@gmail.com>
Signed-off-by: NChris Zankel <chris@zankel.net>

- set up irq registers and call irq_enter/irq_exit once for each kernel
  entry due to interrupt;
- don't attempt to clear current IRQ in the do_interrupt, IRQ handler
  will take care of it;
- find pending interrupt with highest priority before every ISR
  invocation.
Signed-off-by: NMax Filippov <jcmvbkbc@gmail.com>
Signed-off-by: NChris Zankel <chris@zankel.net>

Extract xtensa built-in interrupt controller implementation from
xtensa/kernel/irq.c and move it to other irqchips, providing way to
instantiate it from the device tree.
Signed-off-by: NMax Filippov <jcmvbkbc@gmail.com>
Signed-off-by: NChris Zankel <chris@zankel.net>

Secondary CPUs need this declaration to initialize their MMUs.
Signed-off-by: NMax Filippov <jcmvbkbc@gmail.com>
Signed-off-by: NChris Zankel <chris@zankel.net>

Otherwise exceptions may occur prior to exception handling mechanism
initialization, resulting in silently dead system.
Signed-off-by: NMax Filippov <jcmvbkbc@gmail.com>
Signed-off-by: NChris Zankel <chris@zankel.net>

Provide per-cpu ccount_timer objects and use them appropriately.
Extract per-cpu clockevent setup function.
Signed-off-by: NMax Filippov <jcmvbkbc@gmail.com>
Signed-off-by: NChris Zankel <chris@zankel.net>

This allows ccount to be used as highres timer.
Signed-off-by: NBaruch Siach <baruch@tkos.co.il>
Signed-off-by: NMax Filippov <jcmvbkbc@gmail.com>
Signed-off-by: NChris Zankel <chris@zankel.net>

Signed-off-by: NMax Filippov <jcmvbkbc@gmail.com>
Signed-off-by: NChris Zankel <chris@zankel.net>

Avoid __delay counter underflow for loop counts < 2.
Signed-off-by: NMax Filippov <jcmvbkbc@gmail.com>
Signed-off-by: NChris Zankel <chris@zankel.net>

Signed-off-by: NMax Filippov <jcmvbkbc@gmail.com>
Signed-off-by: NChris Zankel <chris@zankel.net>

This fixes the following build warnings:

arch/xtensa/mm/misc.S: Assembler messages:
arch/xtensa/mm/misc.S:143: Warning: value 0xffffffff30000106 truncated to 0x30000106
arch/xtensa/mm/misc.S:197: Warning: value 0xffffffff30000106 truncated to 0x30000106
Signed-off-by: NMax Filippov <jcmvbkbc@gmail.com>
Signed-off-by: NChris Zankel <chris@zankel.net>

These definitions (-1) were correct when used as a hardware IRQ number,
but are incorrect as a mapped IRQ number.
Signed-off-by: NMax Filippov <jcmvbkbc@gmail.com>
Signed-off-by: NChris Zankel <chris@zankel.net>

This enables the set_robust_list(2) system call.
Signed-off-by: NBaruch Siach <baruch@tkos.co.il>
Signed-off-by: NChris Zankel <chris@zankel.net>

Signed-off-by: NMax Filippov <jcmvbkbc@gmail.com>
Signed-off-by: NChris Zankel <chris@zankel.net>

The code doesn't handle dynamic TAP interface allocation, so there's no
point tracking this case.
Signed-off-by: NMax Filippov <jcmvbkbc@gmail.com>
Signed-off-by: NChris Zankel <chris@zankel.net>

This allows changing MAC address of the device.
Signed-off-by: NMax Filippov <jcmvbkbc@gmail.com>
Signed-off-by: NChris Zankel <chris@zankel.net>

Without proper MAC setup network device doesn't work. IP setup is
redundant and may be done with 'ip=...' kernel parameter.
Signed-off-by: NMax Filippov <jcmvbkbc@gmail.com>
Signed-off-by: NChris Zankel <chris@zankel.net>

Signed-off-by: NMax Filippov <jcmvbkbc@gmail.com>
Signed-off-by: NChris Zankel <chris@zankel.net>

Now 'ethX=...' syntax can actually be used in kernel command line to
specify network interfaces.
Signed-off-by: NMax Filippov <jcmvbkbc@gmail.com>
Signed-off-by: NChris Zankel <chris@zankel.net>

No functional changes, remove dead/unused code, clean checkpatch warnings,
replace strlen of constant strings with sizeof.
Signed-off-by: NMax Filippov <jcmvbkbc@gmail.com>
Signed-off-by: NChris Zankel <chris@zankel.net>

Signed-off-by: NMax Filippov <jcmvbkbc@gmail.com>
Signed-off-by: NChris Zankel <chris@zankel.net>

- drop unused PHYSICAL_MEMORY_ADDRESS and XC_PADDR
- fix NMI_VECTOR_VADDR and INTLEVEL7_VECTOR_VADDR definitions: there
  should be no XCHAL_ prefix in them;
- fix the following warning seen with gcc-4.8.1:

  arch/xtensa/include/asm/vectors.h:71:5: warning: "XCHAL_HAVE_VECBASE" is not defined [-Wundef]
Signed-off-by: NMax Filippov <jcmvbkbc@gmail.com>
Signed-off-by: NChris Zankel <chris@zankel.net>

After commit 88f718e3
"ARM: pxa: delete the custom GPIO header" a compilation
error was introduced in the PXA25x gadget driver.
An attempt to fix the problem was made in
commit b144e4ab
"usb: gadget: fix pxa25x compilation problems"
by explictly stating the driver needs the <mach/hardware.h>
header, which solved the compilation for a few boards,
such as the pxa255-idp and its defconfig.

However the Lubbock board has this special clause in
drivers/usb/gadget/pxa25x_udc.c:

This include file has an implicit dependency on
<mach/irqs.h> having been included before <mach/lubbock.h>
was included.

Before commit 88f718e3
"ARM: pxa: delete the custom GPIO header" this implicit
dependency for the pxa25x_udc compile on the Lubbock was
satisfied by <linux/gpio.h> implicitly including
<mach/gpio.h> which was in turn including <mach/irqs.h>,
apart from the earlier added <mach/hardware.h>.

Fix this by having the PXA25x <mach/lubbock.h> explicitly
include <mach/irqs.h>.
Reported-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Cc: Greg Kroah-Hartmann <gregkh@linuxfoundation.org>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NHaojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Looks like the LCD panel on LDP has been broken quite a while, and
recently got fixed by commit 0b2aa8be (gpio: twl4030: Fix regression
for twl gpio output). However, there's still an issue left where the panel
backlight does not come on if the LCD drivers are built into the
kernel.

Fix the issue by registering the DPI LCD panel only after the twl4030
GPIO has probed.
Reported-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Acked-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
[tony@atomide.com: updated per Tomi's comments]
Signed-off-by: NTony Lindgren <tony@atomide.com>

Commit 7d7e1eba (ARM: OMAP2+: Prepare for irqs.h removal) and commit
ec2c0825 (ARM: OMAP2+: Remove hardcoded IRQs and enable SPARSE_IRQ)
updated the way interrupts for OMAP2/3 devices are defined in the
HWMOD data structures to being an index plus a fixed offset (defined
by OMAP_INTC_START).

Couple of irqs in the OMAP2/3 hwmod data were misconfigured completely
as they were missing this OMAP_INTC_START relative offset. Add this
offset back to fix the incorrect irq data for the following modules:
	OMAP2 - GPMC, RNG
	OMAP3 - GPMC, ISP MMU & IVA MMU
Signed-off-by: NSuman Anna <s-anna@ti.com>
Fixes: 7d7e1eba ("ARM: OMAP2+: Prepare for irqs.h removal")
Fixes: ec2c0825 ("ARM: OMAP2+: Remove hardcoded IRQs and enable SPARSE_IRQ")
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

With commit '7dedd346: ARM: OMAP2+: hwmod: Fix a crash in _setup_reset() with
 DEBUG_LL' we moved from parsing cmdline to identify uart used for earlycon
to using the requsite hwmod CONFIG_DEBUG_OMAPxUARTy FLAGS.

On DRA7 though, we seem to be missing this flag, and atleast on the DRA7 EVM
where we use uart1 for console, boot fails with DEBUG_LL enabled.
Reported-by: NLokesh Vutla <lokeshvutla@ti.com>
Tested-by:  Lokesh Vutla <lokeshvutla@ti.com> # on a different base
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
Fixes: 7dedd346 ("ARM: OMAP2+: hwmod: Fix a crash in _setup_reset() with DEBUG_LL")
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

Linux 3.10 changed the timing of how thread_info->flags is touched:

	x86: Use generic idle loop
	(7d1a9417)

This caused Intel NHM-EX and WSM-EX servers to experience a large number
of immediate MONITOR/MWAIT break wakeups, which caused cpuidle to demote
from deep C-states to shallow C-states, which caused these platforms
to experience a significant increase in idle power.

Note that this issue was already present before the commit above,
however, it wasn't seen often enough to be noticed in power measurements.

Here we extend an errata workaround from the Core2 EX "Dunnington"
to extend to NHM-EX and WSM-EX, to prevent these immediate
returns from MWAIT, reducing idle power on these platforms.

While only acpi_idle ran on Dunnington, intel_idle
may also run on these two newer systems.
As of today, there are no other models that are known
to need this tweak.

Link: http://lkml.kernel.org/r/CAJvTdK=%2BaNN66mYpCGgbHGCHhYQAKx-vB0kJSWjVpsNb_hOAtQ@mail.gmail.comSigned-off-by: NLen Brown <len.brown@intel.com>
Link: http://lkml.kernel.org/r/baff264285f6e585df757d58b17788feabc68918.1387403066.git.len.brown@intel.com
Cc: <stable@vger.kernel.org> # 3.12.x, 3.11.x, 3.10.x
Signed-off-by: NH. Peter Anvin <hpa@linux.intel.com>

Commit 8f34a1da ("arm64: ptrace: use HW_BREAKPOINT_EMPTY type for
disabled breakpoints") fixed an issue with GDB trying to zero breakpoint
control registers. The problem there is that the arch hw_breakpoint code
will attempt to create a (disabled), execute breakpoint of length 0.

This will fail validation and report unexpected failure to GDB. To avoid
this, we treated disabled breakpoints as HW_BREAKPOINT_EMPTY, but that
seems to have broken with recent kernels, causing watchpoints to be
treated as TYPE_INST in the core code and returning ENOSPC for any
further breakpoints.

This patch fixes the problem by prioritising the `enable' field of the
breakpoint: if it is cleared, we simply update the perf_event_attr to
indicate that the thing is disabled and don't bother changing either the
type or the length. This reinforces the behaviour that the breakpoint
control register is essentially read-only apart from the enable bit
when disabling a breakpoint.

Cc: <stable@vger.kernel.org>
Reported-by: NAaron Liu <liucy214@gmail.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

Commit 97bc386f "ARC: Add guard macro to uapi/asm/unistd.h"
inhibited multiple inclusion of ARCH unistd.h. This however hosed the system
since Generic syscall table generator relies on it being included twice,
and in lack-of an empty table was emitted by C preprocessor.

Fix that by allowing one exception to rule for the special case (just
like Xtensa)
Suggested-by: NChen Gang <gang.chen.5i5j@gmail.com>
Signed-off-by: NVineet Gupta <vgupta@synopsys.com>

The r8a7790.dtsi file has four sdhi nodes which the first two have the wrong
resource size for their register block. This causes the sh_modbile_sdhi driver
to fail to communicate with card at-all.

Change sdhi{0,1} node size from 0x100 to 0x200 to correct these nodes
as per Kuninori Morimoto's response to the original patch where all four
nodes where changed. sdhi{2,3} are the correct size.

This bug has been present since sdhi resources were added to the r8a7790 by
8c9b1aa4 ("ARM: shmobile: r8a7790: add MMCIF and SDHI DT
templates") in v3.11-rc2.
Signed-off-by: NBen Dooks <ben.dooks@codethink.co.uk>
Tested-by: NWilliam Towle <william.towle@codethink.co.uk>
Acked-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

4dcfa600
(ARM: DMA-API: better handing of DMA masks for coherent allocations)
exchanged DMA mask check method.
Below warning will appear without this patch

asoc-simple-card asoc-simple-card.0: \
  Coherent DMA mask 0xffffffffffffffff is larger than dma_addr_t allows
asoc-simple-card asoc-simple-card.0: \
  Driver did not use or check the return value from dma_set_coherent_mask()?
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Commit 22ceeee1 ("pwm-backlight: Add
power supply support") added a mandatory power supply for the PWM
backlight. Add a fixed 5V regulator to board code with a consumer supply
entry for the backlight device.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
(cherry picked from commit ad11cb9a5cf96346f1240995c672cdbb5501785c)
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

E.g. landisk_defconfig, which has CONFIG_NTFS_FS=m:

  ERROR: "__ashrdi3" [fs/ntfs/ntfs.ko] undefined!

For "lib-y", if no symbols in a compilation unit are referenced by other
units, the compilation unit will not be included in vmlinux.  This
breaks modules that do reference those symbols.

Use "obj-y" instead to fix this.

http://kisskb.ellerman.id.au/kisskb/buildresult/8838077/

This doesn't fix all cases. There are others, e.g. udivsi3.
This is also not limited to sh, many architectures handle this in the
same way.

A simple solution is to unconditionally include all helper functions.
A more complex solution is to make the choice of "lib-y" or "obj-y" depend
on CONFIG_MODULES:

  obj-$(CONFIG_MODULES) += ...
  lib-y($CONFIG_MODULES) += ...
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Tested-by: NNobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Reviewed-by: NNobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

There are a few subtle races, between change_protection_range (used by
mprotect and change_prot_numa) on one side, and NUMA page migration and
compaction on the other side.

The basic race is that there is a time window between when the PTE gets
made non-present (PROT_NONE or NUMA), and the TLB is flushed.

During that time, a CPU may continue writing to the page.

This is fine most of the time, however compaction or the NUMA migration
code may come in, and migrate the page away.

When that happens, the CPU may continue writing, through the cached
translation, to what is no longer the current memory location of the
process.

This only affects x86, which has a somewhat optimistic pte_accessible.
All other architectures appear to be safe, and will either always flush,
or flush whenever there is a valid mapping, even with no permissions
(SPARC).

The basic race looks like this:

CPU A			CPU B			CPU C

						load TLB entry
make entry PTE/PMD_NUMA
			fault on entry
						read/write old page
			start migrating page
			change PTE/PMD to new page
						read/write old page [*]
flush TLB
						reload TLB from new entry
						read/write new page
						lose data

[*] the old page may belong to a new user at this point!

The obvious fix is to flush remote TLB entries, by making sure that
pte_accessible aware of the fact that PROT_NONE and PROT_NUMA memory may
still be accessible if there is a TLB flush pending for the mm.

This should fix both NUMA migration and compaction.

[mgorman@suse.de: fix build]
Signed-off-by: NRik van Riel <riel@redhat.com>
Signed-off-by: NMel Gorman <mgorman@suse.de>
Cc: Alex Thorlton <athorlton@sgi.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Base pages are unmapped and flushed from cache and TLB during normal
page migration and replaced with a migration entry that causes any
parallel NUMA hinting fault or gup to block until migration completes.

THP does not unmap pages due to a lack of support for migration entries
at a PMD level.  This allows races with get_user_pages and
get_user_pages_fast which commit 3f926ab9 ("mm: Close races between
THP migration and PMD numa clearing") made worse by introducing a
pmd_clear_flush().

This patch forces get_user_page (fast and normal) on a pmd_numa page to
go through the slow get_user_page path where it will serialise against
THP migration and properly account for the NUMA hinting fault.  On the
migration side the page table lock is taken for each PTE update.
Signed-off-by: NMel Gorman <mgorman@suse.de>
Reviewed-by: NRik van Riel <riel@redhat.com>
Cc: Alex Thorlton <athorlton@sgi.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Commit caaa4c80 ("KVM: PPC: Book3S HV: Fix physical address
calculations") unfortunately resulted in some low-order address bits
getting dropped in the case where the guest is creating a 4k HPTE
and the host page size is 64k.  By getting the low-order bits from
hva rather than gpa we miss out on bits 12 - 15 in this case, since
hva is at page granularity.  This puts the missing bits back in.
Reported-by: NAlexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NAlexander Graf <agraf@suse.de>

We don't use PACATOC for PR. Avoid updating HOST_R2 with PR
KVM mode when both HV and PR are enabled in the kernel. Without this we
get the below crash

(qemu)
Unable to handle kernel paging request for data at address 0xffffffffffff8310
Faulting instruction address: 0xc00000000001d5a4
cpu 0x2: Vector: 300 (Data Access) at [c0000001dc53aef0]
    pc: c00000000001d5a4: .vtime_delta.isra.1+0x34/0x1d0
    lr: c00000000001d760: .vtime_account_system+0x20/0x60
    sp: c0000001dc53b170
   msr: 8000000000009032
   dar: ffffffffffff8310
 dsisr: 40000000
  current = 0xc0000001d76c62d0
  paca    = 0xc00000000fef1100   softe: 0        irq_happened: 0x01
    pid   = 4472, comm = qemu-system-ppc
enter ? for help
[c0000001dc53b200] c00000000001d760 .vtime_account_system+0x20/0x60
[c0000001dc53b290] c00000000008d050 .kvmppc_handle_exit_pr+0x60/0xa50
[c0000001dc53b340] c00000000008f51c kvm_start_lightweight+0xb4/0xc4
[c0000001dc53b510] c00000000008cdf0 .kvmppc_vcpu_run_pr+0x150/0x2e0
[c0000001dc53b9e0] c00000000008341c .kvmppc_vcpu_run+0x2c/0x40
[c0000001dc53ba50] c000000000080af4 .kvm_arch_vcpu_ioctl_run+0x54/0x1b0
[c0000001dc53bae0] c00000000007b4c8 .kvm_vcpu_ioctl+0x478/0x730
[c0000001dc53bca0] c0000000002140cc .do_vfs_ioctl+0x4ac/0x770
[c0000001dc53bd80] c0000000002143e8 .SyS_ioctl+0x58/0xb0
[c0000001dc53be30] c000000000009e58 syscall_exit+0x0/0x98
Signed-off-by: NAlexander Graf <agraf@suse.de>

Commit e30b06f4 (ARM: OMAP2+: Remove
legacy mux code for display.c) removed non-DT DSI and HDMI pinmuxing.
However, DSI pinmuxing is still needed, and removing that caused DSI
displays not to work.

This reverts the DSI parts of the commit.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Commit

4178bac4 ARM: call of_clk_init from default time_init handler

added implicit call to of_clk_init() from default time_init callback,
but it did not change platforms calling it from other callbacks, despite
of not having custom time_init callbacks. This caused double clock
initialization on such platforms, leading to boot failures. An example
of such platform is mach-s3c64xx.

This patch fixes boot failure on s3c64xx by dropping custom init_irq
callback, which had a call to of_clk_init() and moving system reset
initialization to init_machine callback. This allows us to have
clocks initialized properly without a need to have custom init_time or
init_irq callbacks.
Signed-off-by: NTomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>