Correcting a simple typo with enabling software defined pins.  I don't
believe this was causing any issues but this is how it was meant to be
implemented.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NEvan Swanson <evan.swanson@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Change remaining direct calls to function pointers.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NEvan Swanson <evan.swanson@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This device lies about supporting phys_id. Remove it and just
let the upper layer report not supported.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Tested-by: <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Recent commits have changed how EEPROM size is checked and if the size
word is misconfigured, the driver will fail to load.  This patch adds a
check for invalid size word in the EEPROM and uses default size instead
for 82576 parts.
Reported-by: NStefan Assmann <sassmann@redhat.com>
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Based on the original patch sent by Stephen Hemminger.

This version incorporates the ethtool changes that Bruce Allan
submitted.

CC: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: NEvan Swanson <evan.swanson@intel.com>

In function 'e100_hw_init':
warning: 'err' may be used uninitialized in this function
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Four years ago, Patrick made a change to hold rtnl mutex during netlink
dump callbacks.

I believe it was a wrong move. This slows down concurrent dumps, making
good old /proc/net/ files faster than rtnetlink in some situations.

This occurred to me because one "ip link show dev ..." was _very_ slow
on a workload adding/removing network devices in background.

All dump callbacks are able to use RCU locking now, so this patch does
roughly a revert of commits :

1c2d670f : [RTNETLINK]: Hold rtnl_mutex during netlink dump callbacks
6313c1e0 : [RTNETLINK]: Remove unnecessary locking in dump callbacks

This let writers fight for rtnl mutex and readers going full speed.

It also takes care of phonet : phonet_route_get() is now called from rcu
read section. I renamed it to phonet_route_get_rcu()
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Remi Denis-Courmont <remi.denis-courmont@nokia.com>
Acked-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Slow path output route resolution always makes sure that
->{saddr,daddr} are set, and also if we trigger into IPSEC resolution
we initialize them as well, because xfrm_lookup() expects them to be
fully resolved.

But if we hit the fast path and flowi4->flowi4_proto is zero, we won't
do this initialization.

Therefore, move the IPSEC path initialization to the route cache
lookup fast path to make sure these are always set.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The rcu protected macros rcu_dereference() and rcu_assign_pointer()
for the bat_priv->primary_if need to be used, as well as spin/rcu locking.

Otherwise we might end up using a primary_if pointer pointing to already
freed memory.
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>
Signed-off-by: NSven Eckelmann <sven@narfation.org>

This is a regression from c4aac1ab

- gw_node_update() doesn't add a new gw_node in case of empty curr_gw.
This means that at the beginning no gw_node is added, leading to an
empty gateway list.

- gw_election() is terminating in case of curr_gw == NULL. It has to
terminate in case of curr_gw != NULL
Signed-off-by: NAntonio Quartulli <ordex@autistici.org>
Signed-off-by: NSven Eckelmann <sven@narfation.org>

atomic_dec_not_zero() is very useful and it is currently defined
multiple times. So it is possible to move it in main.h
Signed-off-by: NAntonio Quartulli <ordex@autistici.org>
Signed-off-by: NSven Eckelmann <sven@narfation.org>

orig_hash_find() manages rcu_lock/unlock internally and doesn't need to
be surrounded by rcu_read_lock() / rcu_read_unlock() anymore
Signed-off-by: NAntonio Quartulli <ordex@autistici.org>
Acked-by: NMarek Lindner <lindner_marek@yahoo.de>
Signed-off-by: NSven Eckelmann <sven@narfation.org>

This makes sure that one cannot request a 99Mbps full-duplex and get a
100Mbps half-duplex configuration in return due to the way the
speed/duplex parameters are handled internally.

Tested: e1000 works
Signed-off-by: NDavid Decotigny <decot@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Initial driver reported different speeds depending on the port being
used. This advertises the speed to be 10Mbps in any case, which is
what it actually is on the wire.
Signed-off-by: NDavid Decotigny <decot@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This tells the NIC to take the speed specified by ethtool into account
when configuring the NIC, instead of keeping the previous speed.
Signed-off-by: NDavid Decotigny <decot@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This updates the network drivers so that they don't access the
ethtool_cmd::speed field directly, but use ethtool_cmd_speed()
instead.

For most of the drivers, these changes are purely cosmetic and don't
fix any problem, such as for those 1GbE/10GbE drivers that indirectly
call their own ethtool get_settings()/mii_ethtool_gset(). The changes
are meant to enforce code consistency and provide robustness with
future larger throughputs, at the expense of a few CPU cycles for each
ethtool operation.

All drivers compiled with make allyesconfig ion x86_64 have been
updated.

Tested: make allyesconfig on x86_64 + e1000e/bnx2x work
Signed-off-by: NDavid Decotigny <decot@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This makes sure the ethtool's set_settings() callback of network
drivers don't ignore the 16 most significant bits when ethtool calls
their set_settings().

All drivers compiled with make allyesconfig on x86_64 have been
updated.
Signed-off-by: NDavid Decotigny <decot@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This makes sure that when a driver calls the ethtool's
get/set_settings() callback of another driver, the data passed to it
is clean. This guarantees that speed_hi will be zeroed correctly if
the called callback doesn't explicitely set it: we are sure we don't
get a corrupted speed from the underlying driver. We also take care of
setting the cmd field appropriately (ETHTOOL_GSET/SSET).

This applies to dev_ethtool_get_settings(), which now makes sure it
sets up that ethtool command parameter correctly before passing it to
drivers. This also means that whoever calls dev_ethtool_get_settings()
does not have to clean the ethtool command parameter. This function
also becomes an exported symbol instead of an inline.

All drivers visible to make allyesconfig under x86_64 have been
updated.
Signed-off-by: NDavid Decotigny <decot@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The 'ep' argument of ethtool_cmd_speed is not altered: advertise it in
protoype. +Indentation fix. Also add comments to advise using the
ethtool_cmd_speed API to get/set the link speed.
Signed-off-by: NDavid Decotigny <decot@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Enable setting speed and auto negotiation parameters for GbE ports.
Hardware do not support half duplex setting currently.

o Update driver version to 5.0.17.
Signed-off-by: NSony Chacko <sony.chacko@qlogic.com>
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o Support ethtool command ETHTOOL_GCHANNELS and ETHTOOL_SCHANNELS.
o Number of rcv rings configuration depend upon number of msix vector.
Signed-off-by: NSucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For backward compatibility, we should retain the module parameters and
sysfs attributes to control the number of peer notifications
(gratuitous ARPs and unsolicited NAs) sent after bonding failover.
Also, it is possible for failover to take place even though the new
active slave does not have link up, and in that case the peer
notification should be deferred until it does.

Change ipv4 and ipv6 so they do not automatically send peer
notifications on bonding failover.

Change the bonding driver to send separate NETDEV_NOTIFY_PEERS
notifications when the link is up, as many times as requested.  Since
it does not directly control which protocols send notifications, make
num_grat_arp and num_unsol_na aliases for a single parameter.  Bump
the bonding version number and update its documentation.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Acked-by: NBrian Haley <brian.haley@hp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pktgen doesn't generate number of frags requested.
Divide packet size by number of frags and fill that in every frags.

Example:
With packet size 1470, it generate only 11 frags. Initial frags
get lenght 706, 353, 177....so on. Last frag get divided by 2.

Now with this fix, each frags will get 78 bytes.
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

module_alloc() and module_free() are available only if CONFIG_MODULES=y
Reported-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that output route lookups update the flow with
destination address selection, we can fetch it from
fl4->daddr instead of rt->rt_dst
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that output route lookups update the flow with
destination address selection, we can fetch it from
fl4->daddr instead of rt->rt_dst
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that output route lookups update the flow with
destination address selection, we can fetch it from
fl4->daddr instead of rt->rt_dst
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that output route lookups update the flow with
destination address selection, we can fetch it from
fl4->daddr instead of rt->rt_dst
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that output route lookups update the flow with
destination address selection, we can fetch it from
fl4->daddr instead of rt->rt_dst
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that output route lookups update the flow with
source address selection, we can fetch it from
fl4->saddr instead of rt->rt_src
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that output route lookups update the flow with
source address selection, we can fetch it from
fl4->saddr instead of rt->rt_src
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that output route lookups update the flow with
source address selection, we can fetch it from
fl4->saddr instead of rt->rt_src
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that output route lookups update the flow with
source address selection, we can fetch it from
fl4->saddr instead of rt->rt_src
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that output route lookups update the flow with
source address et al. selections, the fl4->{saddr,daddr}
assignments here are no longer necessary.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make dst_alloc() and it's users explicitly initialize the entire
entry.

The zero'ing done by kmem_cache_zalloc() was almost entirely
redundant.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now the dst->dev, dev->obsolete, and dst->flags values can
be specified as well.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We don't actually hold the socket lock at this point, so the
rcu_dereference_protected() isn't' correct.  Thanks to Eric
Dumazet for pointing this out.

Thankfully, we're only interested in fetching the faddr value
if srr is enabled, so we can simply make this an RCU sequence
and use plain rcu_dereference().
Reported-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit b9367bf3 ("net: ibmveth: convert to hw_features") accidentally
removed call to ibmveth_set_csum_offload() in ibmveth_probe(). Put the
call back where it was, but with additional error checking provided
by ibmveth_set_features().
Signed-off-by: NMichał Mirosław <mirq-linux@rere.qmqm.pl>
Reported-by: NStephen Rothwell <sfr@canb.auug.org.au>
[sfr: dev -> netdev]
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>