Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Finally, merge these structures and have a single
HW specific data structure.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

A few variables (bssid, bssidmask, curaid) were duplicated in
struct ath_softc and in ath_hal, remove them.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch removes the useless sc_ prefixes for all variables.
Also, refer to interfaces as VIFs and not as VAPs anymore.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Split the core header files into manageable pieces.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use mac80211's primitives for identifying the frame type,
and cleanup the driver-specific macros.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fixed led device naming for the ath9k driver. Due to the
documentation of the led subsystem/class the naming should be
"devicename:colour:function" while not applying sections
should be left blank.

This should lead to e.g. "ath9k-%s::rx" instead of "ath9k-%s:rx".
Signed-off-by: NDanny Kukawka <dkukawka@suse.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Enable operating mode specific interrupts in ath9k_add_interface instead
of ath9k_start.
Signed-off-by: NVivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes an issue where hw_value_short was not being filled
with the proper ratecode during rate registration, but was being used
in the RX path for decoding the packet rate.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The default chainmask for AR9280 is 3, so handle that when setting
the supported MCS rates. Also, check for the HW supported chainmask
when choosing single/dual stream.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Versioning for ath9k is pointless we have kept it at 0.1
since the initial release so its meaningless. We put more emphasis
on kernel release or dated wireless-testing master tag
as per John's tagging.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch enables low-level driver independent debugging of the TSF and remove the driver specific things of ath5k and ath9k from the debugfs.
Signed-off-by: NAlina Friedrichsen <x-alina@gmx.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

AR9285 based devices support only single stream MCS rates.
This patch fixes a bug where dual stream stream rates were
also being registered.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Now that cfg80211 has its own regulatory infrastructure we can
condense ath9k's regulatory code considerably. We only keep data
we need to provide our own regulatory_hint(), reg_notifier() and
information necessary for calibration.

Atheros hardware supports 12 world regulatory domains, since these
are custom we apply them through the the new wiphy_apply_custom_regulatory().
Although we have 12 we can consolidate these into 5 structures based on
frequency and apply a different set of flags that differentiate them on
a case by case basis through the reg_notifier().

If CRDA is not found our own custom world regulatory domain is applied,
this is identical to cfg80211's except we enable passive scan on most
frequencies.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch implements dynamic power save feature for ath9k.
Signed-off-by: NVivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The TX queue draining routines have confusing names,
rename them approprately and merge ath_drain_txdataq()
with ath_drain_all_txq().
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds the platform_driver itself, and modifies the main driver
to register it.

Changes-licensed-under: ISC
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NImre Kaloz <kaloz@openwrt.org>
Tested-by: NPavel Roskin <proski@gnu.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Now that we have converted all bus specific routines to replaceable, we
can move the PCI specific codes into a separate file.

Changes-licensed-under: ISC
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NImre Kaloz <kaloz@openwrt.org>
Tested-by: NPavel Roskin <proski@gnu.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We have left only some PCI specific cleanup code. We have to convert
them as well.

Changes-licensed-under: ISC
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NImre Kaloz <kaloz@openwrt.org>
Tested-by: NPavel Roskin <proski@gnu.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The PCI specific bus_read_cachesize routine won't work on the AHB bus,
we have to replace it with a suitable one later.

Changes-licensed-under: ISC
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NImre Kaloz <kaloz@openwrt.org>
Tested-by: NPavel Roskin <proski@gnu.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Convert to use bus-agnostic DMA routines to make it usable on AHB bus as well.

Changes-licensed-under: ISC
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NImre Kaloz <kaloz@openwrt.org>
Tested-by: NPavel Roskin <proski@gnu.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Convert 'struct pci_dev' to 'struct device' to make it usable on the AHB
bus as well.

Changes-licensed-under: ISC
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NImre Kaloz <kaloz@openwrt.org>
Tested-by: NPavel Roskin <proski@gnu.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Silence sparse by using a defined value PCI_D3hot instead of a magic
constant in a pci_set_power_state() call.
Signed-off-by: NJouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Configure hardware CCMP for management frame protection and use
software crypto when needed.
Signed-off-by: NJouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Return -EOPNOTSUPP if the algorithm is not supported and -ENOSPC if
there is no room in the key cache. This avoids KERN_ERR printk in
mac80211 for "errors" that are actually expected to happen in normal
operating conditions.
Signed-off-by: NJouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The channel_type really doesn't need to be the only member in
a new structure, so remove the struct. Additionally, remove
the _CONF_CHANGE_HT flag and use _CONF_CHANGE_CHANNEL when the
channel type changes, since that's enough of a change to require
reprogramming the hardware anyway.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The set_key callback now seems rather odd, passing a MAC address
instead of a station struct, and a local address instead of a
vif struct. Change that.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Acked-by: Bob Copeland <me@bobcopeland.com> [ath5k]
Acked-by: Ivo van Doorn <ivdoorn@gmail.com> [rt2x00]
Acked-by: Christian Lamparter <chunkeey@web.de> [p54]
Tested-by: Kalle Valo <kalle.valo@nokia.com> [iwl3945]
Tested-by: Samuel Ortiz <samuel@sortiz.org> [iwl3945]
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When we try to change the channel in ath9k its because
either the configuration indicates we *have* changed
channels or HT configuration has changed. In both cases
we want to do a reset. Either way mac80211 will inform us
when we want to actually change the channel so trust those
calls.

Although in the patch it may seem as I am doing more code
changes I am not, all I am doing is removing the initial
branch conditional and shifting the code to the left.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use shiny new conf_is_ht*() helpers, we can later remove ht.enabled if
desired.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ath9k_hw_iscal_supported() just needs to be aware of your band
and if HT20 is being used so lets abandon our internal channel,
HT appended values and internal mode values and use ieee80211_conf
which already carries this information. This works as calibration
is being done for the currently configured channel.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Lets make the request to get the current noise floor threshold
from the EEPROM band specific as it is band specific, not mode
specific.

This also adds a backpointer on the private channel structure
back to the ieee80211_channel structure as this is now needed during
ath9k_hw_getnf().
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

HW reset calls pass the same variables or structs
which we can obtain easily from ah. Although this also applies
during channel changes as we will keep around the ath9k_channel
passed as an argument for now.

We now also now propagate the hw reset errors down.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ath_setcurmode() is a bit misleading, all we are doing is
caching the rate for the corresponding configuration we
are using.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

No need to cache when we want to use 2Mbit/s for all protection
frames for 802.11g as we can determine that dynamically on
ath_buf_set_rate() itself.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>