We don't support 88E6391 anywhere in the code, so remove the unused
mv88e6391_ops structure.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The mv88e6xxx_info structure for the 88E6191 chip was pointing the
mv88e6391_ops definition instead of mv88e6191_ops. Fix this.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The related mv88e6xxx_ops structure was misplaced. Reorder it correctly
to fix this.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The related mv88e6xxx_ops and mv88e6xxx_info structure were misplaced.
Reorder them correctly to fix this.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that DSA has ageing time limits, specify them when registering a
switch so that out-of-range values are handled correctly by the core.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reported-by: NJason Cobham <jcobham@questertangent.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a new operation to disable the DA, SA and VTU priority override.

Setting such limit is not likely to be used soon, so provide a
port_disable_pri_override operation directly. This can be changed later
for port_set_pri_override when we'll need it.

Also remove the now obsolete mv88e6xxx_6320_family helper.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a new operation to disable the limiting of learnt MAC addresses.

Setting such limit is not likely to be used soon, so provide a
port_disable_learn_limit operation directly. This can be changed later
for port_set_learn_limit when we'll need it.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Marvell switch ports can be configured to allow or prevent egress of
frames with an unknown unicast or multicast destination address.

Some switch chips such as 88E6095 and 88E6185 have two disjoint bits in
Port Control Register (0x04) bit 2 "Forward Unknown" (for unicast) and
Port Control 2 Register (0x08) bit 6 "Default Forward" (for multicast).

Other chips such as 88E6085, 88E6123, 88E6352, and 88E6390 have a 2-bit
value in Port Control Register (0x04) bits 3:2 "EgressFloods".

The current code does not fully implement the disjoint bits variant and
assigns incorrect ones to some chip models. Fix that with two
implementation references (6185 and 6352 that I currently have) of a
port_set_egress_floods operation (as named in datasheets).

Old chips such as 88E6060 don't have egress flooding mode, so don't
error out if the operation is not provided.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A switch port mode is defined by the association of its egress mode, its
frame mode and if supported or required, the ether type value.

Pack all this in a mv88e6xxx_set_port_mode function and provide helpers
for the Normal Network mode, the DSA mode, and the Ether Type DSA mode,
as well as an helper to setup a port's mode depending on its nature.

Define PORT_ETH_TYPE_DEFAULT for the 0x9100 reset value of port E Type.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Not all Marvell switch chips support port trunking, which is embedded in
the port vector data for ATU operations.

Rename the portv_trunkid member of the mv88e6xxx_atu_entry structure to
portvec to be more concise and consistent with the different chips.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Rename the _mv88e6xxx_fid_new helper to mv88e6xxx_atu_new to get rid of
the old underscore prefix naming convention and be consistent with the
rest of the chip-wide ATU API.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a fresh documented implementation of the ATU Move operation, and use
it to replace the current ATU Remove operation.

Note that not all Marvell switch chip support the ATU Move operation.
For those supporting it, the number of bits used to mask the destination
port may vary. 6352 and such use 4-bit, while 6390 use 5-bit. Thus add a
new atu_move_port_mask member in the info structure to describe the
presence and variant of ATU Move operation.

Note that the ATU Move operation is not documented in the 6185 datasheet
but the chip does support the operation.

All remaining _mv88e6xxx_atu_* functions are now unused as well as the
MV88E6XXX_FLAG_G1_ATU_FID flag, thus remove them.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a fresh documented implementation of the ATU Flush/Move operation.
Use it to replace the current ATU Flush operation.

_mv88e6xxx_atu_flush_move is still used by the Move operation so keep it
until the Move operation is refactored in a next commit.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add and use a fresh documented implementation of the ATU GetNext.

Since it is not necessary to write the MAC address to iterate from, only
do it once directly in the ATU GetNext operation, if the provided ATU
entry structure is not valid. This makes the user code simpler.

Also, there is no need to loop when getting a single ATU entry. So
remove the mv88e6xxx_atu_get helper and add a simpler snippet in
mv88e6xxx_port_db_load_purge to lookup a given MAC address.

The _mv88e6xxx_atu_mac_{read,write} are not used anymore thus remove
them. _mv88e6xxx_atu_data_{read,write} are still used so keep them.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

All Marvell switch chips have an ATU accessed using the same Global (1)
register layout. Only the handling of the FID differs as more bits were
necessary to support more and more databases.

Add and use a fresh documented implementation of the ATU Load/Purge.

The static mv88e6xxx_g1_atu_{fid_write,op_wait,op,data_write,mac_write}
functions won't need to be exposed in the end so for the moment keep
their counterparts _mv88e6xxx_atu_{wait,cmd,data_write,mac_write} as is,
since they are still used by other ATU operations.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ATU Learn2All feature allows newly learnt addresses to be spanned on
ports marked as "Message Port", currently all DSA ports.

This commit enables this feature which is necessary and quite convenient
for multi-chip switch fabrics.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

All interconnectable Marvell switch chips have an ATU Learn2All feature
which allows newly learnt addresses to be spanned on ports marked as
"Message Port".

This commit configures the DSA ports as Message Port. Note that this has
no effect until the Learn2All feature is enabled.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move the configuration of the default ageing time in a new
mv88e6xxx_atu_setup function.

That function will be extended later to contain all ATU related
configuration bits.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move the ATU ageing time setter code in a new global1_atu.c file, which
will be extended in future patches to contains all consequent Global (1)
ATU support code.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

mv88e6097 chip requires watchdog_ops to be set.
Signed-off-by: NVolodymyr Bendiuga <volodymyr.bendiuga@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement the ops needed to support the watchdog for the MV88E6390
family.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The switch contains a watchdog looking for issues with the internal
gubbins of the switch. Hook the interrupt the watchdog triggers and
log the value of the control register indicating why the watchdog
fired. The watchdog can only be cleared with a switch reset, which
will destroy the current configuration. Rather than doing this, just
disable the interrupt.

The mv88e6390 family has different watchdog registers. So use an ops
structure, so support for the mv88e6390 family can be added later.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move the remaining port configuration code which varies per device
into port.c, using ops were necessary. This makes
mv88e6xxx_6185_family() and mv88e6xxx_6095_family() unused, so remove
them.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Unlike most ports, ports 9 and 10 of the 6390X family have configurable
PHY modes. Set the mode as part of adjust_link().

Ordering is important, because the SERDES interfaces connected to
ports 9 and 10 can be split and assigned to other ports. The CMODE has
to be correctly set before the SERDES interface on another port can be
configured. Such configuration is likely to be performed in
port_enable() and port_disabled(), called on slave_open() and
slave_close().

The simple case is port 9 and 10 are used for 'CPU' or 'DSA'. In this
case, the CMODE is set via a phy-mode in dsa_cpu_dsa_setup(), which is
called early in the switch setup.

When ports 9 or 10 are used as user ports, and have a fixed-phy, when
the fixed fixed-phy is attached, dsa_slave_adjust_link() is called,
which results in the adjust_link function being called, setting the
cmode. The port_enable() will for other ports will be called much
later.

When ports 9 or 10 are used as user ports and have a real phy attached
which does not use all the available SERDES interface, e.g. a 1Gbps
SGMII, there is currently no mechanism in place to set the CMODE of
the port from software. It must be hoped the stripping resistors are
correct.

At the same time, add a function to get the cmode. This will be needed
when configuring the SERDES interfaces.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The MV88E6390 family uses a different ATU age timer coefficient.
Fix the info structures.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The internal PHYs of the mv88e6390 do not have a model ID. Trap any
calls to the ID register, and if it is zero, return the ID for the
mv88e6390. The Marvell PHY driver can then bind to this ID.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Reviewed-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Marvell 88E6341 device is single-chip, 6-port Ethernet switch with
four integrated 10/100/1000Mbps Ethernet transceivers and one high speed
SerDes interfaces.

It belongs to the Topaz family and unlike the 88E6341 it does not have
a TCAM.
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Reviewed-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Marvell 88E6341 device is single-chip, 6-port Ethernet switch with
four integrated 10/100/1000Mbps Ethernet transceivers and one high speed
SerDes interfaces. It is partially compatible with switches of family
88E6352 and switches of family 88E6390.

This commit adds an initial support for this switch by describing its
capabilities to the driver and introducing a new family.
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Reviewed-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some Marvell ethernet switches have internal ethernet transceivers with
hardcoded phy addresses. These addresses can be greater than the number
of ports or its value might be different than the associated port number.
This is for example the case for MV88E6341 that has 6 ports and internal
Port 1 to Port4 PHYs mapped at SMI addresses from 0x11 to 0x14.

This commits fixes the issue by removing the condition in MDIO callbacks.
Signed-off-by: NRomain Perier <romain.perier@free-electrons.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that DSA exposes the bridge device pointer to which a port belongs,
use it when programming the port based VLANs and thus remove the cache.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Upon reception of the NETDEV_CHANGEUPPER, a leaving port is already
unbridged, so reflect this by assigning the port's bridge_dev pointer to
NULL before calling the port_bridge_leave DSA driver operation.

Now that the bridge_dev pointer is exposed to the drivers, reflecting
the current state of the DSA switch fabric is necessary for the drivers
to adjust their port based VLANs correctly.

Pass the bridge device pointer to the port_bridge_leave operation so
that drivers have all information to re-program their chips properly,
and do not need to cache it anymore.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change the ports[DSA_MAX_PORTS] array of the dsa_switch structure for a
zero-length array, allocated at the same time as the dsa_switch
structure itself. A dsa_switch_alloc() helper is provided for that.

This commit brings no functional change yet since we pass DSA_MAX_PORTS
as the number of ports for the moment. Future patches can update the DSA
drivers separately to support dynamic number of ports.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In preparation for allowing dsa_register_switch() to be supplied with
device/platform data, pass down a struct device pointer instead of a
struct device_node.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The mv88e6390 has multiple MDIO busses. Generalize the parsing of the
device tree to support multiple mdio nodes. The external mdio bus has
a compatible strings to indicate it is external.

Keep a linked list of busses, placing the external mdio bus at the
tail of the list. When within the driver an mdio bus is needed,
e.g. for EEE or SERDES, use the head of the list which should be the
internal bus.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Have the MDIO bus driver code allocate a private structure and make
the chip a member of it. This will allow us to add further members in
the future.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In preparation for supporting multiple MDIO busses, pass the mii_bus
structure to all PHY operations. It will in future then be clear on
which MDIO bus the operation should be performed.

For reads/write from phylib, the mii_bus is readily available. However
some internal code also access the PHY, e.g. for EEE and SERDES. Make
this code use the one and only currently available MDIO bus.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The mv88e6165 family has the internal PHYs mapped directly onto the
SMI register space as the switch. So the registers can be read
directly. Put a wrapper around this, in preparation for changing the
signature in order to support the external MDIO bus of the 6390.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Only the Marvell mv88e6xxx DSA driver made use of the HWMON support in
DSA. The temperature sensor registers are actually in the embedded
PHYs, and the PHY driver now supports it. So remove all HWMON support
from DSA and drivers.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Marvell 6352 chip has a 8-bit address/16-bit data EEPROM access.
The Marvell 6390 chip has a 16-bit address/8-bit data EEPROM access.

This patch implements the 8-bit data EEPROM access in the mv88e6xxx
driver and adds its support to chips of the 6390 family.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that we have properly encapsulated and made drivers utilize exported
functions, we can switch dsa_switch_ops to be a annotated with const.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>