Some time ago David Woodhouse reported skb_under_panic
when we try to push ethernet header to fragmented ipv6 skbs.
It was fixed for ipv6 by Florian Westphal in
commit 1d325d21 ("ipv6: ip6_fragment: fix headroom tests and skb leak")

However similar problem still exist in ipv4.

It does not trigger skb_under_panic due paranoid check
in ip_finish_output2, however according to Alexey Kuznetsov
current state is abnormal and ip_fragment should be fixed too.
Signed-off-by: NVasily Averin <vvs@virtuozzo.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The function __mlx4_zone_remove_one_entry always returns zero. So
it is not necessary to check it.

Cc: Joe Jin <joe.jin@oracle.com>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Signed-off-by: NZhu Yanjun <yanjun.zhu@oracle.com>
Reviewed-by: NYuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Computing the alignment manually for going from priv to pub is probably
not such a good idea, and in general the assumption that going from priv
to pub is possible trivially could change, so rather than relying on
that, we change things to just store a pointer to pub. This was sugested
by DaveM in [1].

[1] http://www.spinics.net/lists/netdev/msg443992.htmlSigned-off-by: NJason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Abhishek Shah says:

====================
Extend BGMAC driver for Stingray SoC

The patchset extends Broadcom BGMAC driver for Broadcom Stingray SoC.

This patchset is based on Linux-4.12 and tested on NS2 and Stingray.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Specifying IDM register space in DT is not mendatory for SoCs
where firmware takes care of IDM operations. This patch updates
BGMAC driver's DT binding documentation indicating the same.
Signed-off-by: NAbhishek Shah <abhishek.shah@broadcom.com>
Reviewed-by: NRay Jui <ray.jui@broadcom.com>
Reviewed-by: NOza Oza <oza.oza@broadcom.com>
Reviewed-by: NScott Branden <scott.branden@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

IDM operations are usually one time ops and should be done in
firmware itself. Driver is not supposed to touch IDM registers.

However, for some SoCs', driver is performing IDM read/writes.
So this patch masks IDM operations in case firmware is taking
care of IDM operations.
Signed-off-by: NAbhishek Shah <abhishek.shah@broadcom.com>
Reviewed-by: NOza Oza <oza.oza@broadcom.com>
Reviewed-by: NRay Jui <ray.jui@broadcom.com>
Reviewed-by: NScott Branden <scott.branden@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Return type for idm register write callback should be void as 'writel'
API is used for write operation. However, there no need to have 'return'
in this function.
Signed-off-by: NAbhishek Shah <abhishek.shah@broadcom.com>
Reviewed-by: NOza Oza <oza.oza@broadcom.com>
Reviewed-by: NRay Jui <ray.jui@broadcom.com>
Reviewed-by: NScott Branden <scott.branden@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Marcelo noticed an array overflow caused by commit c28445c3
("sctp: add reconf_enable in asoc ep and netns"), in which sctp
would add SCTP_CID_RECONF into extensions when reconf_enable is
set in sctp_make_init and sctp_make_init_ack.

Then now when all ext chunks are set, 4 ext chunk ids can be put
into extensions array while extensions array size is 3. It would
cause a kernel panic because of this overflow.

This patch is to fix it by defining extensions array size is 4 in
both sctp_make_init and sctp_make_init_ack.

Fixes: c28445c3 ("sctp: add reconf_enable in asoc ep and netns")
Signed-off-by: NXin Long <lucien.xin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

gcc reports that the temporary buffer for computing the
string length may be too small here:

drivers/net/ethernet/cavium/liquidio/lio_ethtool.c: In function 'lio_get_eeprom_len':
/drivers/net/ethernet/cavium/liquidio/lio_ethtool.c:345:21: error: 'sprintf' may write a terminating nul past the end of the destination [-Werror=format-overflow=]
  len = sprintf(buf, "boardname:%s serialnum:%s maj:%lld min:%lld\n",
                     ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/cavium/liquidio/lio_ethtool.c:345:6: note: 'sprintf' output between 35 and 167 bytes into a destination of size 128
  len = sprintf(buf, "boardname:%s serialnum:%s maj:%lld min:%lld\n",

This extends it to 192 bytes, which is certainly enough. As far
as I could tell, there are no other constraints that require a specific
maximum size.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

gcc-7 notices that "-event-%d" could be more than 11 characters long
if we had larger 'vector' numbers:

drivers/net/vmxnet3/vmxnet3_drv.c: In function 'vmxnet3_activate_dev':
drivers/net/vmxnet3/vmxnet3_drv.c:2095:40: error: 'sprintf' may write a terminating nul past the end of the destination [-Werror=format-overflow=]
sprintf(intr->event_msi_vector_name, "%s-event-%d",
                                     ^~~~~~~~~~~~~
drivers/net/vmxnet3/vmxnet3_drv.c:2095:3: note: 'sprintf' output between 9 and 33 bytes into a destination of size 32

The current code is safe, but making the string a little longer
is harmless and lets gcc see that it's ok.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

gcc warns that the temporary buffer might be too small here:

drivers/net/ethernet/cavium/thunder/thunder_bgx.c: In function 'bgx_probe':
drivers/net/ethernet/cavium/thunder/thunder_bgx.c:1020:16: error: '%d' directive writing between 1 and 10 bytes into a region of size between 9 and 11 [-Werror=format-overflow=]
sprintf(str, "BGX%d LMAC%d mode", bgx->bgx_id, lmacid);
             ^~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/cavium/thunder/thunder_bgx.c:1020:16: note: directive argument in the range [0, 2147483647]
drivers/net/ethernet/cavium/thunder/thunder_bgx.c:1020:3: note: 'sprintf' output between 16 and 27 bytes into a destination of size 20

This probably can't happen, but it can't hurt to make it long
enough for the theoretical limit.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

gcc notices that large queue numbers would overflow the queue name
string:

drivers/net/ethernet/broadcom/bnx2x/bnx2x_ethtool.c: In function 'bnx2x_get_strings':
drivers/net/ethernet/broadcom/bnx2x/bnx2x_ethtool.c:3165:25: error: '%d' directive writing between 1 and 10 bytes into a region of size 5 [-Werror=format-overflow=]
drivers/net/ethernet/broadcom/bnx2x/bnx2x_ethtool.c:3165:25: note: directive argument in the range [0, 2147483647]
drivers/net/ethernet/broadcom/bnx2x/bnx2x_ethtool.c:3165:5: note: 'sprintf' output between 2 and 11 bytes into a destination of size 5

There is a hard limit in place that makes the number at most two
digits, so the code is fine. This changes it to use snprintf()
to truncate instead of overflowing, which shuts up that warning.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We get a warning for the port_name string that might be longer than
six characters if we had more than 10 ports:

drivers/net/ethernet/sun/niu.c: In function 'niu_put_parent':
drivers/net/ethernet/sun/niu.c:9563:21: error: '%d' directive writing between 1 and 3 bytes into a region of size 2 [-Werror=format-overflow=]
  sprintf(port_name, "port%d", port);
                     ^~~~~~~~
drivers/net/ethernet/sun/niu.c:9563:21: note: directive argument in the range [0, 255]
drivers/net/ethernet/sun/niu.c:9563:2: note: 'sprintf' output between 6 and 8 bytes into a destination of size 6
  sprintf(port_name, "port%d", port);
  ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/sun/niu.c: In function 'niu_pci_init_one':
drivers/net/ethernet/sun/niu.c:9538:22: error: '%d' directive writing between 1 and 3 bytes into a region of size 2 [-Werror=format-overflow=]
   sprintf(port_name, "port%d", port);
                      ^~~~~~~~
drivers/net/ethernet/sun/niu.c:9538:22: note: directive argument in the range [0, 255]
drivers/net/ethernet/sun/niu.c:9538:3: note: 'sprintf' output between 6 and 8 bytes into a destination of size 6

While we know that the port number is small, there is no harm in
making the format string two bytes longer to avoid the warning.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

One string we pass into the cs->info buffer might be too long,
as pointed out by gcc:

drivers/isdn/divert/isdn_divert.c: In function 'll_callback':
drivers/isdn/divert/isdn_divert.c:488:22: error: '%d' directive writing between 1 and 3 bytes into a region of size between 1 and 69 [-Werror=format-overflow=]
 sprintf(cs->info, "%d 0x%lx %s %s %s %s 0x%x 0x%x %d %d %s\n",
                   ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/isdn/divert/isdn_divert.c:488:22: note: directive argument in the range [0, 255]
drivers/isdn/divert/isdn_divert.c:488:4: note: 'sprintf' output 25 or more bytes (assuming 129) into a destination of size 90

This is unlikely to actually cause problems, so let's use snprintf
as a simple workaround to shut  up the warning and truncate the
buffer instead.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the interface is not up, then don't try to close it during a
shutdown.  This avoids possible double free of the IRQ, which
can happen during a shutdown.

Fixes: 03eb3eb4 ("net: qcom/emac: add shutdown function")
Signed-off-by: NTimur Tabi <timur@codeaurora.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This change enables the use of SW timestamping on Raspberry PI.

smsc95xx uses the usbnet transmit function usbnet_start_xmit(), which
implements software timestamping. However the SOF_TIMESTAMPING_TX_SOFTWARE
capability was missing and only SOF_TIMESTAMPING_RX_SOFTWARE was announced.
By using ethtool_op_get_ts_info() as get_ts_info() also the
SOF_TIMESTAMPING_TX_SOFTWARE is announced.
Signed-off-by: NPetr Kulhavy <brain@jikos.cz>
Reviewed-by: NWoojung Huh <Woojung.Huh@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make name consistent with other TC event notification routines, such as
tcf_add_notify() and tcf_del_notify()
Signed-off-by: NRoman Mashak <mrv@mojatatu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When PACKET_QDISC_BYPASS is not used, Tx queue selection will be done
before the packet is enqueued, taking into account any mappings set by
a queuing discipline such as mqprio without hardware offloading. This
selection may be affected by a previously saved queue_mapping, either on
the Rx path, or done before the packet reaches the device, as it's
currently the case for AF_PACKET.

In order for queue selection to work as expected when using traffic
control, there can't be another selection done before that point is
reached, so move the call to packet_pick_tx_queue to
packet_direct_xmit, leaving the default xmit path as it was before
PACKET_QDISC_BYPASS was introduced.

A forward declaration of packet_pick_tx_queue() is introduced to avoid
the need to reorder the functions within the file.

Fixes: d346a3fa ("packet: introduce PACKET_QDISC_BYPASS socket option")
Signed-off-by: NIván Briano <ivan.briano@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With 802.1ad support the vlan_ingress code started checking for vlan
protocol mismatch which causes the current tag to be inserted and the
bridge vlan protocol & pvid to be set. The vlan tag insertion changes
the skb mac_header and thus the lookup mac dest pointer which was loaded
prior to calling br_allowed_ingress in br_handle_frame_finish is VLAN_HLEN
bytes off now, pointing to the last two bytes of the destination mac and
the first four of the source mac causing lookups to always fail and
broadcasting all such packets to all ports. Same thing happens for locally
originated packets when passing via br_dev_xmit. So load the dest pointer
after the vlan checks and possible skb change.

Fixes: 8580e211 ("bridge: Prepare for 802.1ad vlan filtering support")
Reported-by: NAnitha Narasimha Murthy <anitha@cumulusnetworks.com>
Signed-off-by: NNikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: NToshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Check ptp_clock_register() return not only for NULL but
also for error pointers, and also nullify adapter->ptp_clock
if ptp_clock_register() fails.

Fixes: 9c33e420 ("cxgb4: Add PTP Hardware Clock (PHC) support")
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current code only support DT method to control xge led.
This patch is the implementation of acpi method to control xge led.
Signed-off-by: NLiuJian <liujian56@huawei.com>
Reviewed-by: NJohn Garry <john.garry@huawei.com>
Reviewed-by: NYunsheng Lin <linyunsheng@huawei.com>
Reviewed-by: NDaode Huang <huangdaode@hisilicon.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When we convert atomic_t to refcount_t, a new kernel warning
on "increment on 0" is introduced in the netpoll code,
zap_completion_queue(). In fact for this special case, we know
the refcount is 0 and we just have to set it to 1 to satisfy
the following dev_kfree_skb_any(), so we can just use
refcount_set(..., 1) instead.

Fixes: 63354797 ("net: convert sk_buff.users from atomic_t to refcount_t")
Reported-by: NDave Jones <davej@codemonkey.org.uk>
Cc: Reshetova, Elena <elena.reshetova@intel.com>
Signed-off-by: NCong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some firmwares in Huawei E3372H devices have been observed to switch back
to NTB 32-bit format after altsetting switch.
This patch implements a driver flag to check for the device settings and
set NTB format to 16-bit again if needed.
The flag has been activated for devices controlled by the huawei_cdc_ncm.c
driver.

V1->V2:
- fixed broken error checks
- some corrections to the commit message
V2->V3:
- variable name changes, to clarify what's happening
- check (and possibly set) the NTB format later in the common bind code path
Signed-off-by: NEnrico Mioso <mrkiko.rs@gmail.com>
Reported-and-tested-by: NChristian Panton <christian@panton.org>
Reviewed-by: NBjørn Mork <bjorn@mork.no>
CC: Bjørn Mork <bjorn@mork.no>
CC: Christian Panton <christian@panton.org>
CC: linux-usb@vger.kernel.org
CC: netdev@vger.kernel.org
CC: Oliver Neukum <oliver@neukum.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

mdio_mux_init parses the child nodes of the MDIO mux. When using
"mdio-mux-mmioreg" the child nodes are describing the register value
that is written to switch between the MDIO busses.

The change which makes the error messages more verbose changed the
parsing of the "reg" property from a simple of_property_read_u32 call
to of_mdio_parse_addr. On a Khadas VIM (based on the Meson GXL SoC,
which uses mdio-mux-mmioreg) this prevents registering the MDIO mux
(because the "reg" values on the MDIO mux child nodes are 0x2009087f
and 0xe40908ff) and leads to the following errors:
  mdio-mux-mmioreg c883455c.eth-phy-mux: /soc/periphs@c8834000/eth-phy-mux/mdio@e40908ff PHY address -469169921 is too large
  mdio-mux-mmioreg c883455c.eth-phy-mux: Error: Failed to find reg for child /soc/periphs@c8834000/eth-phy-mux/mdio@e40908ff
  mdio-mux-mmioreg c883455c.eth-phy-mux: /soc/periphs@c8834000/eth-phy-mux/mdio@2009087f PHY address 537462911 is too large
  mdio-mux-mmioreg c883455c.eth-phy-mux: Error: Failed to find reg for child /soc/periphs@c8834000/eth-phy-mux/mdio@2009087f
  mdio-mux-mmioreg c883455c.eth-phy-mux: Error: No acceptable child buses found
  mdio-mux-mmioreg c883455c.eth-phy-mux: failed to register mdio-mux bus /soc/periphs@c8834000/eth-phy-mux
(as a result of that ethernet is not working, because the PHY which is
connected through the mux' child MDIO bus, which is not being
registered).

Fix this by reverting the change from of_mdio_parse_addr to
of_mdio_parse_addr.

Fixes: 342fa196 ("mdio: mux: make child bus walking more permissive and errors more verbose")
Signed-off-by: NMartin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: NNeil Armstrong <narmstrong@baylibre.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The configure callback of fib_rules_ops can change the refcnt of a
fib rule. For instance, mlxsw takes a refcnt when adding the processing
of the rule to a work queue. Thus the rule refcnt can not be reset to
to 1 afterwards. Move the refcnt setting to after the allocation.

Fixes: 5361e209 ("net: avoid one splat in fib_nl_delrule()")
Signed-off-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NRolf Eike Beer <eb@emlix.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add 0x50a3 and 0x50a4 T5 device id's
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Don't populate array error_code on the stack but make it static. Makes
the object code smaller by almost 250 bytes:

Before:
   text	   data	    bss	    dec	    hex	filename
  10366	    983	      0	  11349	   2c55	net/dccp/input.o

After:
   text	   data	    bss	    dec	    hex	filename
  10161	   1039	      0	  11200	   2bc0	net/dccp/input.o
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Don't populate array glrt_table on the stack but make it static.
Makes the object code a smaller by over 670 bytes:

Before:
   text	   data	    bss	    dec	    hex	filename
 131772	   4733	      0	 136505	  21539	rt2800lib.o

After:
   text	   data	    bss	    dec	    hex	filename
 131043	   4789	      0	 135832	  21298	rt2800lib.o
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Acked-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Don't populate array route_possibilities on the stack but make it
static const.  Makes the object code a little smaller by 85 bytes:

Before:
   text	   data	    bss	    dec	    hex	filename
   9901	   2448	      0	  12349	   303d	dwmac4_core.o

After:
   text	   data	    bss	    dec	    hex	filename
   9760	   2504	      0	  12264	   2fe8	dwmac4_core.o
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Don't populate various tables on the stack but make them static const.
Makes the object code smaller by nearly 200 bytes:

Before:
   text	   data	    bss	    dec	    hex	filename
 113468	  11200	      0	 124668	  1e6fc	bnx2x_ethtool.o

After:
   text	   data	    bss	    dec	    hex	filename
 113129	  11344	      0	 124473	  1e639	bnx2x_ethtool.o
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Acked-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This change fixes following problem

[    1.827940] xgene-enet: probe of 1f210030.ethernet failed with error -2

which leads to a missing ethernet interface (reproducable at least on
Gigabyte MP30-AR0 and APM Mustang systems).

The check for a valid clk resource fails, because DT doesn't provide a
clock for sgenet1. But the driver doesn't use this clk, if the ethernet
port is connected via SGMII. Therefore this patch avoids probing for clk
on SGMII interfaces.

Fixes: 9aea7779 ("drivers: net: xgene: Fix crash on DT systems")
Signed-off-by: NThomas Bogendoerfer <tbogendoerfer@suse.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The bpf_skb_adjust_net() ignores the return value of bpf_skb_net_shrink/grow,
and always return 0, fix it by return 'ret'.
Signed-off-by: NKefeng Wang <wangkefeng.wang@huawei.com>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pull networking fixes from David Miller:

1) Fix 64-bit division in mlx5 IPSEC offload support, from Ilan Tayari
   and Arnd Bergmann.

2) Fix race in statistics gathering in bnxt_en driver, from Michael
   Chan.

3) Can't use a mutex in RCU reader protected section on tap driver, from
   Cong WANG.

4) Fix mdb leak in bridging code, from Eduardo Valentin.

5) Fix free of wrong pointer variable in nfp driver, from Dan Carpenter.

6) Buffer overflow in brcmfmac driver, from Arend van SPriel.

7) ioremap_nocache() return value needs to be checked in smsc911x
   driver, from Alexey Khoroshilov.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (34 commits)
  net: stmmac: revert "support future possible different internal phy mode"
  sfc: don't read beyond unicast address list
  datagram: fix kernel-doc comments
  socket: add documentation for missing elements
  smsc911x: Add check for ioremap_nocache() return code
  brcmfmac: fix possible buffer overflow in brcmf_cfg80211_mgmt_tx()
  net: hns: Bugfix for Tx timeout handling in hns driver
  net: ipmr: ipmr_get_table() returns NULL
  nfp: freeing the wrong variable
  mlxsw: spectrum_switchdev: Check status of memory allocation
  mlxsw: spectrum_switchdev: Remove unused variable
  mlxsw: spectrum_router: Fix use-after-free in route replace
  mlxsw: spectrum_router: Add missing rollback
  samples/bpf: fix a build issue
  bridge: mdb: fix leak on complete_info ptr on fail path
  tap: convert a mutex to a spinlock
  cxgb4: fix BUG() on interrupt deallocating path of ULD
  qed: Fix printk option passed when printing ipv6 addresses
  net: Fix minor code bug in timestamping.txt
  net: stmmac: Make 'alloc_dma_[rt]x_desc_resources()' look even closer
  ...

I made the mistake of upgrading my desktop to the new Fedora 26 that
comes with gcc-7.1.1.

There's nothing wrong per se that I've noticed, but I now have 1500
lines of warnings, mostly from the new format-truncation warning
triggering all over the tree.

We use 'snprintf()' and friends in a lot of places, and often know that
the numbers are fairly small (ie a controller index or similar), but gcc
doesn't know that, and sees an 'int', and thinks that it could be some
huge number.  And then complains when our buffers are not able to fit
the name for the ten millionth controller.

These warnings aren't necessarily bad per se, and we probably want to
look through them subsystem by subsystem, but at least during the merge
window they just mean that I can't even see if somebody is introducing
any *real* problems when I pull.

So warnings disabled for now.
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Pull modules updates from Jessica Yu:
 "Summary of modules changes for the 4.13 merge window:

   - Minor code cleanups

   - Avoid accessing mod struct prior to checking module struct version,
     from Kees

   - Fix racy atomic inc/dec logic of kmod_concurrent_max in kmod, from
     Luis"

* tag 'modules-for-v4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/jeyu/linux:
  module: make the modinfo name const
  kmod: reduce atomic operations on kmod_concurrent and simplify
  module: use list_for_each_entry_rcu() on find_module_all()
  kernel/module.c: suppress warning about unused nowarn variable
  module: Add module name to modinfo
  module: Pass struct load_info into symbol checks

Since internal phy-mode is reserved for non-xMII protocol we cannot use
it with dwmac-sun8i.
Furthermore, all DT patchs which comes with this patch were cleaned, so
the current state is broken.
This reverts commit 1c2fa5f8 ("net: stmmac: support future possible different internal phy mode")

Fixes: 1c2fa5f8 ("net: stmmac: support future possible different internal phy mode")
Signed-off-by: NCorentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If we have more than 32 unicast MAC addresses assigned to an interface
we will read beyond the end of the address table in the driver when
adding filters. The next 256 entries store multicast addresses, so we
will end up attempting to insert duplicate filters, which is mostly
harmless. If we add more than 288 unicast addresses we will then read
past the multicast address table, which is likely to be more exciting.

Fixes: 12fb0da4 ("sfc: clean fallbacks between promisc/normal in efx_ef10_filter_sync_rx_mode")
Signed-off-by: NBert Kenward <bkenward@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Stephen Hemminger says:

====================
minor net kernel-doc fixes

Fix a couple of small errors in kernel-doc for networking
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

An underscore in the kernel-doc comment section has special meaning
and mis-use generates an errors.

./net/core/datagram.c:207: ERROR: Unknown target name: "msg".
./net/core/datagram.c:379: ERROR: Unknown target name: "msg".
./net/core/datagram.c:816: ERROR: Unknown target name: "t".
Signed-off-by: NStephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>