We can not allow the worker to run after its fbdev, or even the module,
has been removed.

Fixes: cfe63423 ("drm/fb-helper: Add drm_fb_helper_set_suspend_unlocked()")
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Noralf Trønnes <noralf@tronnes.org>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: dri-devel@lists.freedesktop.org
Cc: <stable@vger.kernel.org> # v4.9+
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170207124956.14954-2-chris@chris-wilson.co.uk

We can not allow the worker to run after its fbdev, or even the module,
has been removed.

Fixes: eaa434de ("drm/fb-helper: Add fb_deferred_io support")
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Noralf Trønnes <noralf@tronnes.org>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: dri-devel@lists.freedesktop.org
Cc: <stable@vger.kernel.org> # v4.7+
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170207124956.14954-1-chris@chris-wilson.co.uk

fix warning:

drivers/gpu/drm/rockchip/cdn-dp-reg.c:632:24: warning:
  'val[1]' may be used uninitialized in this function [-Wmaybe-uninitialized]
  msa_misc = 2 * val[0] + 32 * val[1] +
Signed-off-by: NMark Yao <mark.yao@rock-chips.com>

copy_from_user_inatomic() is actually a local function that returns
-EFAULT or positive values on error.  Otherwise copy_from_user() returns
the number of bytes remaining to be copied.  We want to return -EFAULT
here.

I removed an unlikely() because we just did a copy_from_user()
so I don't think it can possibly make a difference.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NRob Clark <robdclark@gmail.com>

Extend the DSI PHY/PLL drivers to support the DSI 14nm PHY/PLL
found on 8x96.

These are picked up from the downstream driver. The PHY part is similar
to the other DSI PHYs. The PLL driver requires some trickery so that
one DSI PLL can drive both the DSIs (i.e, dual DSI mode).

In the case of dual DSI mode. One DSI instance becomes the clock master,
and other the clock slave. The master PLL's output (Byte and Pixel clock)
is fed to both the DSI hosts/PHYs.

When the DSIs are configured in dual DSI mode, the PHY driver communicates
to the PLL driver using msm_dsi_pll_set_usecase() which instance is the
master and which one is the slave. When setting rate, the master PLL also
configures some of the slave PLL/PHY registers which need to be identical
to the master's for correct dual DSI behaviour.

There are 2 PLL post dividers that should have ideally been modelled as
generic clk_divider clocks, but require some customization for dual DSI.
In particular, when the master PLL's post-diviers are set, the slave PLL's
post-dividers need to be set too. The clk_ops for these use clk_divider's
helper ops and flags internally to prevent redundant code.

Cc: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NArchit Taneja <architt@codeaurora.org>
Signed-off-by: NRob Clark <robdclark@gmail.com>

The 14nm DSI PHY on 8x96 (called PHY v2 downstream) requires a different
set of calculations for computing D-PHY timing params. Create a
timing_calc_v2 func for the newer v2 PHYs.
Signed-off-by: NHai Li <hali@codeaurora.org>
Signed-off-by: NArchit Taneja <architt@codeaurora.org>
Signed-off-by: NRob Clark <robdclark@gmail.com>

Since DSI PHY has been a separate platform device, it should not
depend on the resources in host to be functional. This change is
to trigger PHY operations in manager, instead of host, so that
host and PHY can be completely separated.
Signed-off-by: NHai Li <hali@codeaurora.org>
Signed-off-by: NArchit Taneja <architt@codeaurora.org>
Signed-off-by: NRob Clark <robdclark@gmail.com>

In case of dual DSI, some registers in PHY1 have been programmed
during PLL0 clock's set_rate. The PHY1 reset called by host1 later
will silently reset those PHY1 registers. This change is to reset
and enable both PHYs before any PLL clock operation.

[Originally worked on by Hai Li <hali@codeaurora.org>. Fixed up
by Archit Taneja <architt@codeaurora.org>]
Signed-off-by: NArchit Taneja <architt@codeaurora.org>
Signed-off-by: NRob Clark <robdclark@gmail.com>

For some new types of DSI PHY, more settings depend on
use cases controlled by DSI manager. This change allows
DSI manager to setup PHY with a use case.
Signed-off-by: NHai Li <hali@codeaurora.org>
Signed-off-by: NArchit Taneja <architt@codeaurora.org>
Signed-off-by: NRob Clark <robdclark@gmail.com>

The DSI host is required to configure more timings calculated
in PHY. By introducing a shared structure, this change allows
more timing information passed from PHY to host.
Signed-off-by: NHai Li <hali@codeaurora.org>
Signed-off-by: NArchit Taneja <architt@codeaurora.org>
Signed-off-by: NRob Clark <robdclark@gmail.com>

Create an init() op for dsi_phy which sets up things specific to
a given DSI PHY.

The dsi_phy driver probe expects every DSI version to get a
"dsi_phy_regulator" mmio base. This isn't the case for 8x96.
Creating an init() op will allow us to accommodate such
differences.
Signed-off-by: NArchit Taneja <architt@codeaurora.org>
Signed-off-by: NRob Clark <robdclark@gmail.com>

Add 8x96 DSI data in dsi_cfg. The downstream kernel's dsi_host driver
enables core_mmss_clk. We're seeing some branch clock warnings on
8x96 when enabling this. There doesn't seem to be any negative effect
with not enabling this clock, so use it once we figure out why we
get the warnings.
Signed-off-by: NArchit Taneja <architt@codeaurora.org>
Signed-off-by: NRob Clark <robdclark@gmail.com>

The driver returns an error if a DSI DT node is populated, but no device
is connected to it or if the data-lane map isn't present. Ideally, such
a DSI node shouldn't be probed at all (i.e, its status should be set to
"disabled in DT"), but there isn't any harm in registering the DSI device
even if it doesn't have a bridge/panel connected to it.
Signed-off-by: NArchit Taneja <architt@codeaurora.org>
Signed-off-by: NRob Clark <robdclark@gmail.com>

This code has been more or less picked up from the vc4 and intel
implementations of update_plane() funcs for cursor planes.

The update_plane() func is usually the drm_atomic_helper_update_plane
func that will issue an atomic commit with the plane updates. Such
commits are not intended to be done faster than the vsync rate.

The legacy cursor userspace API, on the other hand, expects the kernel
to handle cursor updates immediately.

Create a fast path in update_plane, which updates the cursor registers
and flushes the configuration. The fast path is taken when there is only
a change in the cursor's position in the crtc, or a change in the
cursor's crop co-ordinates. For anything else, we go via the slow path.

We take the slow path even when the fb changes, and when there is
currently no fb tied to the plane. This should hopefully ensure that we
always take a slow path for every new fb. This in turn should ensure that
the fb is pinned/prepared.
Signed-off-by: NArchit Taneja <architt@codeaurora.org>
Signed-off-by: NRob Clark <robdclark@gmail.com>

In mdp5_plane_atomic_check, we get crtc_state from drm_plane_state.

Later, for cursor planes, we'll populate the update_plane() func that
takes a fast asynchronous path to implement cursor movements. There, we
would need to call a similar atomic_check func to validate the plane
state, but crtc_state would need to be derived differently.

Refactor mdp5_plane_atomic_check to mdp5_plane_atomic_check_with_state
such that the latter takes crtc_state as an argument.

This is similar to what the intel driver has done for async cursor
updates.
Signed-off-by: NArchit Taneja <architt@codeaurora.org>
Signed-off-by: NRob Clark <robdclark@gmail.com>

Register cursor drm_planes. The loop in modeset_init that inits the
planes and crtcs has to be refactored a bit. We first iterate all the
hwpipes to find the cursor planes. Then, we loop again to create
crtcs.

In msm_atomic_wait_for_commit_done, remove the check which bypasses
waiting for vsyncs if state->legacy_cursor_updates is true.

We will later create a fast path for cursor position changes in the
cursor plane's update_plane func that doesn't go via the regular
atomic commit path. For rest of cursor related updates, we will have
to wait for vsyncs, so ignore the legacy_cursor_updates flag.
Signed-off-by: NArchit Taneja <architt@codeaurora.org>
Signed-off-by: NRob Clark <robdclark@gmail.com>

These are various changes added in preparation for cursor planes:

- Add a pipe_cursor block for 8x96 in mdp5_cfg.
- Add a new pipe CAP called MDP_PIPE_CAP_CURSOR. Use this to ensure we
  assign a cursor SSPP for a drm_plane with type DRM_PLANE_TYPE_CURSOR.
- Update mdp5_ctl_blend_mask/ext_blend_mask funcs to incorporate cursor
  SSPPs.
- In mdp5_ctl_blend, iterate through MAX_STAGES instead of stage_cnt,
  we need to do this because we can now have empty stages in between.
- In mdp5_crtc_atomic_check, make sure that the cursor plane has the
  highest zorder, and stage the cursor plane to the maximum stage #
  present on the HW.
- Create drm_crtc_funcs that doesn't try to implement cursors using the
  older LM cursor HW.
- Pass drm_plane_type in mdp5_plane_init instead of a bool telling
  whether plane is primary or not.
Signed-off-by: NArchit Taneja <architt@codeaurora.org>
Signed-off-by: NRob Clark <robdclark@gmail.com>

In MDP5 Layer Mixer HW, the blender output is only the blended color
components (i.e R, G and B, or COLOR0/1/2 in MDP5 HW terminology). This
is fed to the BG input of the next blender. We also need to provide an
alpha (COLOR3) value for the BG input at the next stage.

This is configured via using the REG_MDP5_LM_BLEND_COLOR_OUT register.
For each stage, we can propagate either the BG or FG alpha to the next
stage.

The approach taken by the driver is to propagate FG alpha, if the plane
staged on that blender has an alpha. If it doesn't, we try to propagate
the base layer's alpha.

This is borrowed from downstream MDP5 kernel driver. Without this, we
don't see any cursor plane content.
Signed-off-by: NArchit Taneja <architt@codeaurora.org>
Signed-off-by: NRob Clark <robdclark@gmail.com>

The MDP5 plane's atomic_check ops doesn't perform clipping tests.
This didn't hurt us much in the past, but clipping becomes important
with cursor planes.

Use drm_plane_helper_check_state, the way rockchip/intel/mtk drivers
already do. Use these drivers as reference.

Clipping requires knowledge of the crtc width and height. This requires
us to call drm_atomic_helper_check_modeset before
drm_atomic_helper_check_planes in the driver's atomic_check op, because
check_modetest will populate the mode for the crtc, needed to populate
the clip rectangle.

We update the plane_enabled(state) local helper to use state->visible,
since state->visible and 'state->fb && state->crtc' represent the same
thing.

One issue with the existing code is that we don't have a way to disable
the plane when it's completely clipped out. Until there isn't an update
on the crtc (which would de-stage the plane), we would still see the
plane in its last 'visible' configuration.
Signed-off-by: NArchit Taneja <architt@codeaurora.org>
Signed-off-by: NRob Clark <robdclark@gmail.com>

Use SSPP_NONE in mdp5_plane_pipe() if there is now hwpipe allocated for
the drm_plane. Returning '0' means we are returning VIG0 pipe.

Also, use the mdp5_pipe enum to pass around the stage array. Initialize
the stage to SSPP_NONE by default.

We do the above because 1) Cursor plane has to be staged at the topmost
blender of the LM, which can result in empty stages in between 2) In
the future, when we support multiple LMs per CRTC. We could have stages
which don't have any pipe assigned to them.
Signed-off-by: NArchit Taneja <architt@codeaurora.org>
Signed-off-by: NRob Clark <robdclark@gmail.com>

We currently create CRTCs equaling to the # of Layer Mixer blocks we
have on the MDP5 HW. This number is generally more than the # of encoders
(INTFs) we have in the MDSS HW. The number of encoders connected to
displays on the platform (as described by DT) would be even lesser.

Create only N drm_crtcs, where N is the number of drm_encoders
successfully registered. To do this, we call modeset_init_intf() before
we init the drm_crtcs and drm_planes.

Because of this change, setting encoder->possible_crtcs needs to be moved
from construct_encoder() to a later point when we know how many CRTCs we
have.
Signed-off-by: NArchit Taneja <architt@codeaurora.org>
Signed-off-by: NRob Clark <robdclark@gmail.com>

Count can't be non-zero. Changing to uint will also prevent future
warnings.
Signed-off-by: NArchit Taneja <architt@codeaurora.org>
Signed-off-by: NRob Clark <robdclark@gmail.com>

For the DSI interfaces, the mdp5_kms core creates 2 encoders for video
and command modes.

Create only a single encoder per interface. When creating the encoder, set
the interface type to MDP5_INTF_MODE_NONE. It's the bridge (DSI/HDMI/eDP)
driver's responsibility to set a different interface type. It can use the
the kms func op set_encoder_mode to change the mode of operation, which
in turn would configure the interface type for the INTF.

In mdp5_cmd_encoder.c, we remove the redundant code, and make the commmand
mode funcs as helpers that are used in mdp5_encoder.c
Signed-off-by: NArchit Taneja <architt@codeaurora.org>
Signed-off-by: NRob Clark <robdclark@gmail.com>

Rename the mdp5_encoder_* ops for active displays to
mdp5_vid_encoder_* ops.
Signed-off-by: NArchit Taneja <architt@codeaurora.org>
Signed-off-by: NRob Clark <robdclark@gmail.com>

The mdp5 kms driver currently sets up multiple encoders per interface
(INTF), one for each kind of mode of operation it supports.
We create 2 drm_encoders for DSI, one for Video Mode and the other
for Command Mode operation. The reason behind this approach could have
been that we aren't aware of the DSI device's mode of operation when
we create the encoders.

This makes things a bit complicated, since these encoders have to
be further attached to the same DSI bridge. The easier way out is
to create a single encoder, and make the DSI driver set its mode
of operation when we know what the DSI device's mode flags are.

Start with providing a way to set the mdp5_intf_mode using a kms
func that sets the encoder's mode of operation. When constructing
a DSI encoder, we set the mode of operation to Video Mode as
default. When the DSI device is attached to the host, we probe the
DSI mode flags and set the corresponding mode of operation.
Signed-off-by: NArchit Taneja <architt@codeaurora.org>
Signed-off-by: NRob Clark <robdclark@gmail.com>

We currently create 2 encoders for DSI interfaces, one for command
mode and other for video mode operation. This isn't needed as we
can't really use both the encoders at the same time. It also makes
connecting bridges harder.

Switch to creating a single encoder. For now, we assume that the
encoder is configured only in video mode. Later, the same encoder
would be usable in both modes.
Signed-off-by: NArchit Taneja <architt@codeaurora.org>
Signed-off-by: NRob Clark <robdclark@gmail.com>

The commit "drm: bridge: Link encoder and bridge in core code" updated
the drm_bridge_attach() API to also include the drm_encoder pointer
the bridge attaches to.

The func msm_dsi_manager_bridge_init() now relies on the drm_encoder
pointer stored in msm_dsi->encoders to pass the encoder to the bridge
API.

msm_dsi->encoders is unfortunately set after this function is called,
resulting in us passing a NULL pointer to drm_brigde_attach. This
results in an error and the DSI driver probe fails.

Move the initialization of msm_dsi->encoders[] a bit up. Also, don't
try to set the encoder's bridge. That's now managed by the bridge
API.

Cc: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NArchit Taneja <architt@codeaurora.org>
Signed-off-by: NRob Clark <robdclark@gmail.com>

Signed-off-by: NArchit Taneja <architt@codeaurora.org>
Signed-off-by: NRob Clark <robdclark@gmail.com>

Signed-off-by: NArchit Taneja <architt@codeaurora.org>
Signed-off-by: NRob Clark <robdclark@gmail.com>

Define the block in advance so that the generated mdp5.xml.h doesn't
break build.
Signed-off-by: NArchit Taneja <architt@codeaurora.org>
Signed-off-by: NRob Clark <robdclark@gmail.com>

Signed-off-by: NRob Clark <robdclark@gmail.com>

Suggested by Rob Herring.  We still support the old names for
compatibility with downstream android dt files.

Cc: Rob Herring <robh@kernel.org>
Signed-off-by: NRob Clark <robdclark@gmail.com>
Reviewed-by: NEric Anholt <eric@anholt.net>
Acked-by: NRob Herring <robh@kernel.org>

This was never documented or used in upstream dtb.  It is used by
downstream bindings from android device kernels.  But the quirks are
a property of the gpu revision, and as such are redundant to be listed
separately in dt.  Instead, move the quirks to the device table.
Signed-off-by: NRob Clark <robdclark@gmail.com>
Reviewed-by: NEric Anholt <eric@anholt.net>

The original way we determined the gpu version was based on downstream
bindings from android kernel.  A cleaner way is to get the version from
the compatible string.

Note that no upstream dtb uses these bindings.  But the code still
supports falling back to the legacy bindings (with a warning), so that
we are still compatible with the gpu dt node from android device
kernels.
Signed-off-by: NRob Clark <robdclark@gmail.com>
Reviewed-by: NEric Anholt <eric@anholt.net>
Acked-by: NRob Herring <robh@kernel.org>

The plan is to use the OPP bindings.  For now, remove the documentation
for qcom,gpu-pwrlevels, and make the driver fall back to a safe low
clock if the node is not present.

Note that no upstream dtb use this node.  For now we keep compatibility
with this node to avoid breaking compatibility with downstream android
dt files.
Signed-off-by: NRob Clark <robdclark@gmail.com>
Reviewed-by: NEric Anholt <eric@anholt.net>
Acked-by: NRob Herring <robh@kernel.org>

With atomic modesetting the hardware will be powered off when the
mode_set function is called.  We should configure the hardware in the
enable function.
Signed-off-by: NChris Zhong <zyw@rock-chips.com>

Sometimes the Dock is disconnected, but cdn_dp_encoder_disable is not
triggered by DRM. For example, unplug the Dock in console mode, and
re-plug it again, the cdn_dp_event_work will try to get the sink count
of Dock, since the DP is still active. But the Dock has been powered
down, it need re-power on, and wait for a while until it is ready to
DPCD communication.
Signed-off-by: NChris Zhong <zyw@rock-chips.com>

We're trying to lock mutex when cdn-dp shutdown, so we need to make
sure the mutex is inited in cdn-dp's probe.
Signed-off-by: NJeffy Chen <jeffy.chen@rock-chips.com>
Reviewed-by: NGuenter Roeck <groeck@chromium.org>
Reviewed-by: NChris Zhong <zyw@rock-chips.com>
Signed-off-by: NChris Zhong <zyw@rock-chips.com>

The cdn_dp_pd_event_work is using drm_helper_hpd_irq_event to update the
connector status, this function is used to update all connectors of
drm_device. Therefore, the detect of other connector will be call, when
cdn_dp_pd_event_work is triggered, every time. It is not necessary, and
it may cause system crash. replace drm_helper_hpd_irq_event with
drm_kms_helper_hotplug_event, only update cdn-dp status.
Signed-off-by: NChris Zhong <zyw@rock-chips.com>
Tested-by: NGuenter Roeck <groeck@chromium.org>
Reviewed-by: NGuenter Roeck <groeck@chromium.org>

If the driver is in suspended mode, the dp block may be disabled, and
chip registers may not be accessible. Yet, the worker may be triggered
in this situation by an extcon event. If that happens, the following crash
will be seen.

cdn-dp fec00000.dp: [drm:cdn_dp_pd_event_work] *ERROR* Enable dp failed -19
cdn-dp fec00000.dp: [drm:cdn_dp_pd_event_work] Connected, not enabled. Enabling cdn
Bad mode in Error handler detected, code 0xbf000002 -- SError
CPU: 1 PID: 10357 Comm: kworker/1:2 Not tainted 4.4.21-05903-ge0514ea #1
Hardware name: Google Kevin (DT)
Workqueue: events cdn_dp_pd_event_work
task: ffffffc0cda67080 ti: ffffffc0b9b80000 task.ti: ffffffc0b9b80000
PC is at cdn_dp_clock_reset+0x30/0xa8
LR is at cdn_dp_enable+0x1e0/0x69c
...
Call trace:
[<ffffffc0005a7e24>] cdn_dp_pd_event_work+0x58/0x3f4
[<ffffffc0002397f0>] process_one_work+0x240/0x424
[<ffffffc00023a28c>] worker_thread+0x2fc/0x424
[<ffffffc00023f5fc>] kthread+0x10c/0x114
[<ffffffc000203dd0>] ret_from_fork+0x10/0x40

Problem is two-fold: The worker should not run while suspended, and the
suspend function should not call cdn_dp_disable() while the worker is
running.
Signed-off-by: NGuenter Roeck <groeck@chromium.org>
Signed-off-by: NSean Paul <seanpaul@chromium.org>
Signed-off-by: NChris Zhong <zyw@rock-chips.com>