Previously enabled poll(2) support on one edge was never reconfigured when
sysfs polarity change was triggered from kernel, because 'struct device
*dev' shadowed an earlier definition.

Found by sparse, which I should've run much earlier.
Signed-off-by: NJani Nikula <ext-jani.1.nikula@nokia.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

JEDEC eMMC specification version 4.4 (MMCA 4.4) defines Extended CSD
structure versions up to 5.
Signed-off-by: NAdrian Hunter <adrian.hunter@nokia.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The main bug was that 'blk_cleanup_queue()' was called while the block
device could still be in use, for example, because the card was removed
while files were still open.

In addition, to be sure that 'mmc_request()' will get called for all new
requests (so it can error them out), the queue is emptied during cleanup.
This is done after the worker thread is stopped to avoid racing with it.

Finally, it is not a device error for this to be happening, so quiet the
(sometimes very many) error messages.
Signed-off-by: NAdrian Hunter <adrian.hunter@nokia.com>
Cc: <linux-mmc@vger.kernel.org>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

If mmc_blk_set_blksize() fails mmc_blk_probe() the request queue and its
thread have been set up and they need to be shut down properly before
putting the disk.
Signed-off-by: NJarkko Lavinen <jarkko.lavinen@nokia.com>
Signed-off-by: NAdrian Hunter <adrian.hunter@nokia.com>
Cc: <linux-mmc@vger.kernel.org>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

When a card is removed before mmc_blk_probe() has called add_disk(), then
the minor field is uninitialized and has value 0.  This caused
mmc_blk_put() to always release devidx 0 even if 0 was still in use.  Then
the next mmc_blk_probe() used the first free idx of 0, which oopses in
sysfs, since it is used by another card.
Signed-off-by: NAnna Lemehova <EXT-Anna.Lemehova@nokia.com>
Signed-off-by: NAdrian Hunter <adrian.hunter@nokia.com>
Cc: <linux-mmc@vger.kernel.org>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Warning(drivers/base/power/main.c:453): No description found for parameter 'dev'
Warning(drivers/base/power/main.c:453): No description found for parameter 'cb'
Warning(drivers/base/power/main.c:719): No description found for parameter 'dev'
Warning(drivers/base/power/main.c:719): No description found for parameter 'state'
Warning(drivers/base/power/main.c:719): No description found for parameter 'cb'
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Commit cbda12d7 (drm/i915: implement
new pm ops for i915), among other things, removed the .suspend and
.resume pointers from the struct drm_driver object in i915_drv.c,
which broke resume without KMS on my MSI Wind U100.

Fix this by reverting that part of commit cbda12d7.

[ The DRM layer will not use the class-specific suspend/resume functions
  if the driver is marked MODESET-aware, and conversely it will not
  register the PCI device if the drievr isn't so marked, so you always
  end up with _either_ the drm-class suspend/resume _or_ the PCI layer
  PM functionality, never both.  - Linus ]
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Acked-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The mask happens to be the same, but the IH is reading the status, not the
not the control register.
Signed-off-by: NLuca Tettamanti <kronos.it@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

If a NULL value is possible, the dereference should only occur after the
NULL test.

Coverity CID: 13338
Signed-off-by: NDarren Jenkins <darrenrjenkins@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

If a NULL value is possible, the dereference should only occur after the
NULL test.

Coverity CID: 13335
Signed-off-by: NDarren Jenkins <darrenrjenkins@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

If a NULL value is possible, the dereference should only occur after the
NULL test.

Coverity CID: 13334
Signed-off-by: NDarren Jenkins <darrenrjenkins@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

The encoder variable can be NULL in this function so I believe it should
be checked before dereference.

Coverity CID: 13253

[airlied: extremely unlikely to happen]
Signed-off-by: NDarren Jenkins <darrenrjenkins@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Stanse found a memory leak in radeon_master_create. master_priv is not
freed/assigned on all paths. Fix that.
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This always evaluates to true.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NAdam Jackson <ajax@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NAdam Jackson <ajax@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

drm_pci_alloc() has input of address mask for setting pci dma
mask on the device, which should be properly setup by drm driver.
And leave it as a param for drm_pci_alloc() would cause confusion
or mistake would corrupt the correct dma mask setting, as seen on
intel hw which set wrong dma mask for hw status page. So remove
it from drm_pci_alloc() function.
Signed-off-by: NZhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Correct misspelled "CONFIG_IPv6" that was introduced in commit
d14714df ("IB/addr: Fix IPv6 routing lookup").  The config variable
should be all uppercase.
Signed-off-by: NRobert P. J. Day <rpjday@crashcourse.ca>

[ This was my fault when I munged the original patch.  - Roland ]
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

If mlx4_init_port_info() fails, cleanup the initialized ports only.
Signed-off-by: NEli Cohen <eli@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

In mlx4_ib_post_recv(), we should check the queue for overflow using
recv_cq instead of send_cq (current code looks like a copy-and-paste
mistake).
Signed-off-by: NOr Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

As for memfree mthca hardware, ConnectX also requires SRQ WQE scatter
entries to be initialized with the invalid L_Key at SRQ creation time.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

This one reverts 9e3a6d15.
As reported by http://bugzilla.kernel.org/show_bug.cgi?id=14485,
this dump will cause hang problem on some machine. If something
really needs this kind of full registers dump, that could be done
within intel-gpu-tools.

Cc: Ben Gamari <bgamari.foss@gmail.com>
Signed-off-by: NZhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

For some clocks, the old Ironlake DPLL calculator wold give m/n/p
combinations that didn't match the spreadsheet of what HW validation
tests.  Instead, use the G4X DPLL calculator, which does a better job
at it.

So we use the intel_g4x_find_best_pll to calculate the DPLL for CRT/HDMI/LVDS
on ironlake. At the same time to consider the dpll setting for display port, we
add the display port DPLL limit on ironlake, which will directly use the
function of intel_find_pll_ironlake_dp to get the corresponding dpll setting.
Signed-off-by: NZhao Yakui <yakui.zhao@intel.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

Select the correct BPC for LVDS on Ironlake. If it is 18-bit LVDS panel,
the BPC will be 6. When it is 24-bit LVDS panel, the BPC will 8.
At the same time the BPC will be 8 when the output device is CRT/HDMI/DP.
Signed-off-by: NZhao Yakui <yakui.zhao@intel.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

Make the BPC in FDI rx/transcoder be consistent with that in pipeconf on Ironlake.
Signed-off-by: NZhao Yakui <yakui.zhao@intel.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

Enable/disable the dithering for LVDS based on VBT setting. On the 965/g4x
platform the dithering flag is defined in LVDS register. And on the ironlake
the dithering flag is defined in pipeconf register.
Signed-off-by: NZhao Yakui <yakui.zhao@intel.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

As pinning (allocating and binding GTT memory) does not actually invoke
GPU commands, it is safe, and indeed is attempted, during resumption
from suspension:

  [drm:intel_init_clock_gating] *ERROR* failed to pin power context: -16
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reported-by: NHugh Dickins <hugh.dickins@tiscali.co.uk>
Cc: stable@kernel.org
Signed-off-by: NEric Anholt <eric@anholt.net>

Hugh found an error path where we were attempting to unref a bo without
holding the struct mutex:

  [drm:intel_init_clock_gating] *ERROR* failed to pin power context: -16
  ------------[ cut here ]------------
  WARNING: at drivers/gpu/drm/drm_gem.c:438 drm_gem_object_free+0x20/0x5e()
  Hardware name: ESPRIMO Mobile V5505
  Modules linked in: snd_pcm_oss snd_mixer_oss snd_seq snd_seq_device
  Pid: 3793, comm: s2ram Not tainted 2.6.33-rc2 #4
  Call Trace:
   [<7815298e>] warn_slowpath_common+0x59/0x6b
   [<781529b3>] warn_slowpath_null+0x13/0x18
   [<78317c1a>] ? drm_gem_object_free+0x20/0x5e
   [<78317c1a>] drm_gem_object_free+0x20/0x5e
   [<78317bfa>] ? drm_gem_object_free+0x0/0x5e
   [<7829df11>] kref_put+0x38/0x45
   [<7833a5f0>] intel_init_clock_gating+0x232/0x271
   [<78317bfa>] ? drm_gem_object_free+0x0/0x5e
   [<7832c307>] i915_restore_state+0x21a/0x2b3
   [<7832379d>] i915_resume+0x3c/0xbb
   [<78174fe5>] ? trace_hardirqs_on_caller+0xfc/0x123
   [<7831c756>] ? drm_class_resume+0x0/0x3e
   [<7831c78d>] drm_class_resume+0x37/0x3e
   [<78351e0a>] legacy_resume+0x1e/0x51
   [<78351ece>] device_resume+0x91/0xab
   [<7831c756>] ? drm_class_resume+0x0/0x3e
   [<78352226>] dpm_resume+0x58/0x10f
   [<783522fb>] dpm_resume_end+0x1e/0x2c
   [<78180f80>] suspend_devices_and_enter+0x61/0x84
   [<78180ff8>] enter_state+0x55/0x83
   [<7818091c>] state_store+0x94/0xaa
   [<7829d09e>] kobj_attr_store+0x1e/0x23
   [<782098e0>] sysfs_write_file+0x66/0x99
   [<781cd2f0>] vfs_write+0x8a/0x108
   [<781cd408>] sys_write+0x3c/0x63
   [<78125c10>] sysenter_do_call+0x12/0x36
  ---[ end trace a343537f29950fda ]---

It is in fact slightly more insiduous that first appears since we are
attempting to not just free the object without the lock, but are trying
to do the whole bo manipulation without holding the lock.
Reported-by: NHugh Dickins <hugh.dickins@tiscali.co.uk>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Signed-off-by: NEric Anholt <eric@anholt.net>

drivers/gpu/drm/i915/i915_dma.c: In function 'i915_driver_load':
drivers/gpu/drm/i915/i915_dma.c:1114: warning: 'll_base' may be used uninitialized in this function

Partly this is because gcc isn't smart enough.  But `ll_base' does get used
uninitialised in the DRM_DEBUG() call.

Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Eric Anholt <eric@anholt.net>
Cc: Dave Airlie <airlied@linux.ie>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NEric Anholt <eric@anholt.net>

The C99 specification states in section 6.11.5:

The placement of a storage-class specifier other than at the beginning
of the declaration specifiers in a declaration is an obsolescent
feature.
Signed-off-by: NTobias Klauser <tklauser@distanz.ch>
Signed-off-by: NEric Anholt <eric@anholt.net>

This code generally fails to adjust the render clock, and when it does,
it conflicts with some other register settings and can cause problems.

So remove this code altogether.  I'm reworking it now to do the right
thing, but the only bit it will share is the VBT check for whether
reclocking is supported, so I'm leaving that bit.

Reverts most of 652c393a ("add dynamic
clock frequency control"), though for many the regressions showed up
in the later 181a5336 ("Fix render
reclock availability detection").
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NEric Anholt <eric@anholt.net>

We restored RC6 twice on resume, even with modesetting off.  Instead,
only restore it once and skip RC6 initialization entirely in non-KMS mode.
Signed-off-by: NAndy Lutomirski <luto@mit.edu>
Tested-by: NJeff Chua <jeff.chua.linux@gmail.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

This patch adds a new execbuf ioctl, execbuf2, for use by clients that
want to control fence register allocation more finely.  The buffer
passed in to the new ioctl includes a new relocation type to indicate
whether a given object needs a fence register assigned for the command
buffer in question.

Compatibility with the existing execbuf ioctl is implemented in terms
of the new code, preserving the assumption that fence registers are
required for pre-965 rendering commands.
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
[ickle: Remove pre-emptive clear_fence_reg()]
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NKristian Høgsberg <krh@bitplanet.net>
[anholt: Removed dmesg spam]
Signed-off-by: NEric Anholt <eric@anholt.net>

Should fix fdo bug 25741
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Look up primary dac adj values from the table if
there is no bios or bios dac table to reference.

The lookup table may need to be adjusted for certain
families.

Should fix kernel bug 14945.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

if necessary for combios

Some early combios radeon cards don't have a connector
table or dac table in the bios, if they do not, fallback
to the default tables.

Should fix kernel bug 14963.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

nuc900 ethernet driver uses mii_xx_xx serials api, so mii module should be selected.
Signed-off-by: Nlijie <eltshanli@gmail.com>
Acked-by: NWan ZongShun <mcuos.com@gmail.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The Correcteable/Uncorrectable Error Mask Registers are used by PCIe AER
driver which will controls the reporting of individual errors to PCIe RC
via PCIe error messages.

If hardware masks special error reporting to RC, the aer_inject driver
should not inject aer error.
Acked-by: NAndi Kleen <ak@linux.intel.com>
Signed-off-by: NYouquan, Song <youquan.song@intel.com>
Acked-by: NYing, Huang <ying.huang@intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

It turns out that some PCI devices require extra delays when changing
power state from D3 to D0 (and the other way around).  Although this
is against the PCI specification, we can handle it quite easily by
allowing drivers to define arbitrary D3 delays for devices known to
require extra time for switching power states.

Introduce additional field d3_delay in struct pci_dev and use it to
store the value of the device's D0->D3 delay, in miliseconds.  Make
the PCI PM core code use the per-device d3_delay unless
pci_pm_d3_delay is greater (in which case the latter is used).
[This also allows the driver to specify d3_delay shorter than the
 10 ms required by the PCI standard if the device is known to be able
 to handle that.]

Make the sky2 driver set d3_delay to 150 for devices handled by it.

Fixes http://bugzilla.kernel.org/show_bug.cgi?id=14730 which is a
listed regression from 2.6.30.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

In bbc_envctrl_init() we have to unlink the fan and temp instances
from the lists because our caller is going to free up the 'bp' object
if we return an error.

We can't rely upon bbc_envctrl_cleanup() to do this work for us in
this case.
Reported-by: NPatrick Finnegan <pat@computer-refuge.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>