This patch makes the station table maintenance safer. Two flags are
maintained:

1) if station is present in driver
2) if station is present in uCode

This will allow us in the future to deal with more stations than the
firmware allows.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds eeprom version display into device/version sysfs file
/sys/class/net/wlanX/devices/version
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NGregory Greenman <gregory.greenman@intel.com>
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch configures uCode to use open loop tx power algorithm
via TX_POWER_DBM (0x98) host command.
Signed-off-by: NGregory Greenman <gregory.greenman@intel.com>
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch sets the rfkill state to RFKILL_STATE_HARD_BLOCKED when the
radio is killed by the hardware switch.
Signed-off-by: NAdel Gadllah <adel.gadllah@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch removes the usage RFKILL_STATE_ON and uses
RFKILL_STATE_UNBLOCKED instead.
Signed-off-by: NAdel Gadllah <adel.gadllah@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NPavel Roskin <proski@gnu.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Provide MAC time, rate, channel, signal and noise.
Signed-off-by: NPavel Roskin <proski@gnu.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Don't try to skip any headers in hostap_80211_header_parse().  We never
use that function for interfaces affected by local->monitor_type.  Both
the master and the AP interface receive 802.11 frames without any
additional headers.
Signed-off-by: NPavel Roskin <proski@gnu.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes the rfkill deps for iwl4965/5000
and removes the input device usage.
Signed-off-by: NAdel Gadllah <adel.gadllah@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Correct typo introduced by "wireless: remove RFKILL_STATE_HARD_BLOCKED
warnings".
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

synchronize_irq() is superfluous when free_irq() call immediately follows it,
because free_irq() also does a synchronize_irq() call of its own.
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Clean up config/burst value arch-specific setup.

* bcrvalue only varied by its big-endian bit
* crvalue only varied for certain types of x86-32 chips

This should make fealnx quite a bit more portable, without any behavior
change.
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

DE_UNALIGNED_16 is always being passed a u16 *, no need to have the
wrapper with two casts in it, just call get_unaligned directly.
Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

We currently don't signal the kernel we that this device can wake
the system.  Call device_init_wakeup() to correct this.
Without this device_can_wakeup and device_may_wakeup will return
incorrect values.
Together with the minimized acpi wakeup patch (6/4 ;)), which will
follow in the next mail, this really makes wake-on-lan work for me
as expected (i.e. "ethtool -s eth0 wol g" is sufficient, no
additional magic needed).
Signed-off-by: NTobias Diedrich <ranma+kernel@tdiedrich.de>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Clean up the following errors and warnings reported by checkpatch.pl:
 + ERROR: Macros with complex values should be enclosed in parenthesis
 + WARNING: __func__ should be used instead of gcc specific __FUNCTION__
 + WARNING: plain inline is preferred over __inline__
 + WARNING: Use #include <linux/io.h> instead of <asm/io.h>
 + WARNING: Use #include <linux/uaccess.h> instead of <asm/uaccess.h>

The changes were verified with by comparing the "objdump -d 8139too.ko"
output which is exactly the same for the old and new version in case of
config CONFIG_8139TOO=m, CONFIG_8139TOO_PIO=n, CONFIG_8139TOO_TUNE_TWISTER=n,
CONFIG_8139TOO_8129=n, CONFIG_8139_OLD_RX_RESET=n.
Software versions used: gcc 4.2.3, objdump 2.18.0.20080103, on elf32-i386.
Signed-off-by: NMárton Németh <nm127@freemail.hu>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Pass buffer length to rndis_command so that rndis_command can read full
response buffer from device instead of max CONTROL_BUFFER_SIZE bytes.
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Fix compile error on sh_eth and remove base address macro.
Signed-off-by: NNobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

The call to e1000_clean_tx_irq in e1000_netpoll can race with the call
to e1000_clean_tx_irq in e1000_clean.  With a small bit of tweaking to
to netpoll_send_skb to simulate a system that was under extreme stress,
I was able to reproduce these concurrent calls.  This can result in
multiple frees to the skbs on the tx ring buffer.

Dropping this call from e1000_netpoll should be fine since we can rely
on the calls in e1000_clean to do what is needed since napi will poll
the hardware just after calling poll_controller.
Signed-off-by: NAndy Gospodarek <andy@greyhouse.net>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

This patch makes igb driver ioport-free.
This corrects behavior in probe function so as not to request ioport
resources as long as they are not really needed.
Signed-off-by: NTaku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

This patch makes e1000e driver ioport-free.
This corrects behavior in probe function so as not to request ioport
resources as long as they are not really needed.
Signed-off-by: NTaku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

We do not want to prolong the situation much longer that e1000
and e1000e support these devices at the same time. As a result,
take out the bandage that was added for the interim period
and remove all the PCI Express device IDs from e1000.
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Signed-off-by: NAndre Haupt <andre@bitwigglers.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

clock is already cpu-endian (see le32_to_cpu slightly before), so
le64_to_cpu doesn't make much sense.
Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This fixes a circular locking dependency in the workqueue handling.
The interface work task uses the mac80211 function
ieee80211_iterate_active_interfaces() which grabs the RTNL lock.

However when the interface is brough down, this happens under the RTNL
lock as well, this causes problems because mac80211 will flush the workqueue
during the ifdown event. This causes mac80211 to wait until the driver has
completed all work which can't finish because it is waiting on the RTNL lock.

This is fixed by moving rt2x00 workqueue tasks on a different workqueue,
this workqueue can be flushed when the ieee80211_hw structure is removed
by the driver (when the driver is unloaded) which does not happen under the
RTNL lock.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

  CC [M]  drivers/net/wireless/b43/rfkill.o
drivers/net/wireless/b43/rfkill.c: In function ‘b43_rfkill_soft_toggle’:
drivers/net/wireless/b43/rfkill.c:90: warning: enumeration value ‘RFKILL_STATE_HARD_BLOCKED’ not handled in switch

  CC [M]  drivers/net/wireless/b43legacy/rfkill.o
drivers/net/wireless/b43legacy/rfkill.c: In function ‘b43legacy_rfkill_soft_toggle’:
drivers/net/wireless/b43legacy/rfkill.c:92: warning: enumeration value ‘RFKILL_STATE_HARD_BLOCKED’ not handled in switch

  CC [M]  drivers/net/wireless/iwlwifi/iwl-rfkill.o
drivers/net/wireless/iwlwifi/iwl-rfkill.c: In function ‘iwl_rfkill_soft_rf_kill’:
drivers/net/wireless/iwlwifi/iwl-rfkill.c:56: warning: enumeration value ‘RFKILL_STATE_HARD_BLOCKED’ not handled in switch

Also handle RFKILL_STATE_{ON,OFF} -> RFKILL_STATE_{UNBLOCKED,SOFT_BLOCKED}
conversion since I'm already here...
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

  CC [M]  drivers/net/wireless/ath5k/base.o
drivers/net/wireless/ath5k/base.c: In function ‘ath5k_tx’:
drivers/net/wireless/ath5k/base.c:2598: warning: unused variable ‘info’
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Small whitespace cleanups for wireless drivers
Signed-off-by: NPavel Machek <pavel@suse.cz>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fix iwlwifi so that it builds cleanly with CONFIG_INPUT=n.
Also free the input device on exit.

drivers/built-in.o: In function `iwl_rfkill_unregister':
(.text+0xbf430): undefined reference to `input_unregister_device'
drivers/built-in.o: In function `iwl_rfkill_init':
(.text+0xbf51c): undefined reference to `input_allocate_device'
drivers/built-in.o: In function `iwl_rfkill_init':
(.text+0xbf5bf): undefined reference to `input_register_device'
drivers/built-in.o: In function `iwl_rfkill_init':
(.text+0xbf5e9): undefined reference to `input_free_device'
net/built-in.o: In function `rfkill_disconnect':
rfkill-input.c:(.text+0xe71e1): undefined reference to `input_close_device'
rfkill-input.c:(.text+0xe71e9): undefined reference to `input_unregister_handle'
net/built-in.o: In function `rfkill_connect':
rfkill-input.c:(.text+0xe723e): undefined reference to `input_register_handle'
rfkill-input.c:(.text+0xe724d): undefined reference to `input_open_device'
rfkill-input.c:(.text+0xe725c): undefined reference to `input_unregister_handle'
net/built-in.o: In function `rfkill_handler_init':
rfkill-input.c:(.init.text+0x36ec): undefined reference to `input_register_handler'
net/built-in.o: In function `rfkill_handler_exit':
rfkill-input.c:(.exit.text+0x112c): undefined reference to `input_unregister_handler'
make[1]: *** [.tmp_vmlinux1] Error 1
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This fixes a clobber of the skb that was introduced by the
tx_control->cb conversion patches.
This bug causes a crash when the skb destructor is invoked. That happens
on skb_orphan or skb_kfree.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

During rt2x00usb_disable_radio() all pending urb's should
be killed and not only those from the RX queue.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This change cleans up the ath5k LED code and converts it to use
the standard LED device class along with the rx/tx LED triggers
provided by mac80211.
Signed-off-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When rt2x00queue_alloc_rxskbs() fails rt2x00queue_unitialize()
will be called which will free all rxskb. So we don't need
to do this in the rt2x00queue_alloc_rxskb() function as well.

rt2x00queue_free_skb() unmaps the DMA but doesn't clear the
allocation flag. Since the code is copied from rt2x00queue_unmap_skb()
anyway (and that function does clear the flag) we might as well
use that function directly.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This adds a firmware debugging knob to debugfs.
With this knob it's possible to enable advanced runtime firmware
checks.
For now it only implements one sanity check for the mac-suspend.
In future there'll probably be more.
If CONFIG_B43_DEBUG is disabled, these checks will collapse to nothing.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This adds a simple firmware watchdog for the opensource firmware.
This will check every 15 seconds, if the firmware zeroed out the watchdog
register. The firmware will do this in its eventloop.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This is a rewrite of the DMA API for SSB devices.
This is needed, because the old (non-existing) "API" made too many bad
assumptions on the API of the host-bus (PCI).
This introduces an almost complete SSB-DMA-API that maps to the lowlevel
bus-API based on the bustype.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

dev_close() must be called holding the RTNL.  Compile-tested only.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

dev_close() must be called holding the RTNL.  Compile-tested only.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

s2io has IOMMU overflow checking, but unfortunately it is wrong.

It didn't use the standard macros, which meant that it only worked
on POWER and SPARC because only those define DMA_ERROR_CODE. Convert it to
use the standard macros instead.

I also commented two more bugs in the IOMMU handling. It assumes
that 0 DMA addresses cannot happen, but that's not true in all IOMMU setups.
The information if a buffer has been already mapped needs to be stored
elsewhere.

Didn't fix those because it needs careful checking of the buffer handling
by the maintainers.

Cc: ram.vepa@neterion.com
Cc: santosh.rastapur@neterion.com
Cc: sivakumar.subramani@neterion.com
Cc: sreenivasa.honnur@neterion.com
Signed-off-by: NAndi Kleen <ak@linux.intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

When enabling TSO via ethool on e1000, it is possible to set
NETIF_F_TSO6 on hardware that does not support it.  Setting TSO via
ethtool now matches the settings used when the hardware is probed.
Signed-off-by: NAndy Gospodarek <andy@greyhouse.net>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

The E100 device can't work on current kernel (2.6.26-rc6) and will cause
kernel corruption on intel ixdp4xx.
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>